Kod: Zaznacz cały
/*
Copyright (C) AC SOFTWARE SP. Z O.O.
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
as published by the Free Software Foundation; either version 2
of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
*/
#include <SuplaDevice.h>
#include <supla/control/relay.h>
#include <supla/control/sequence_button.h>
// Choose proper network interface for your card:
#ifdef ARDUINO_ARCH_AVR
// Arduino Mega with EthernetShield W5100:
#include <supla/network/ethernet_shield.h>
// Ethernet MAC address
uint8_t mac[6] = {0x00, 0x01, 0x02, 0x03, 0x04, 0x05};
Supla::EthernetShield ethernet(mac);
// Arduino Mega with ENC28J60:
// #include <supla/network/ENC28J60.h>
// Supla::ENC28J60 ethernet(mac);
#elif defined(ARDUINO_ARCH_ESP8266) || defined(ARDUINO_ARCH_ESP32)
// ESP8266 and ESP32 based board:
#include <supla/network/esp_wifi.h>
Supla::ESPWifi wifi("your_wifi_ssid", "your_wifi_password");
#endif
void setup() {
Serial.begin(115200);
// Replace the falowing GUID with value that you can retrieve from https://www.supla.org/arduino/get-guid
char GUID[SUPLA_GUID_SIZE] = {0x3E,0x0D,0xF4,0x1C,0xE3,0x0E,0x45,0x0B,0xC6,0x28,0x8C,0xAD,0xB4,0xFA,0xAA,0x88};
// Replace the following AUTHKEY with value that you can retrieve from: https://www.supla.org/arduino/get-authkey
char AUTHKEY[SUPLA_AUTHKEY_SIZE] = {0x3E,0x8E,0xF8,0x12,0x06,0xF2,0x0F,0xD8,0xB2,0xE5,0x69,0xF4,0x70,0x4B,0x78,0x05};
/*
* Having your device already registered at cloud.supla.org,
* you want to change CHANNEL sequence or remove any of them,
* then you must also remove the device itself from cloud.supla.org.
* Otherwise you will get "Channel conflict!" error.
*/
auto secretRelay = new Supla::Control::Relay(30, false); // Low level trigger relay on pin 30
auto alarmRelay = new Supla::Control::Relay(31, false); // Low level trigger relay on pin 31
auto seqButton = new Supla::Control::SequenceButton(28, true, true); // Button on pin 28 with internal pullUp
// and LOW is considered as "pressed" state
// Sequence of lenghts [ms] of button being presset, released, pressed, released, etc.
// Aplication will print on Serial recorded sequence, so use it to record your rhythm and put it here
uint16_t sequence[30] = {90, 590, 90, 140, 90, 290, 90, 230, 90, 140, 90};
seqButton->setSequence(sequence);
seqButton->setMargin(0.5); // we allow +- 50% deviation of state length compared to matching sequence
// Button will trigger secretRelay when correct rhythm will be detected or alarmRelay otherwise
seqButton->addAction(Supla::TURN_ON, secretRelay, Supla::ON_SEQUENCE_MATCH);
seqButton->addAction(Supla::TURN_ON, alarmRelay, Supla::ON_SEQUENCE_DOESNT_MATCH);
/*
* SuplaDevice Initialization.
* Server address is available at https://cloud.supla.org
* If you do not have an account, you can create it at https://cloud.supla.org/account/create
* SUPLA and SUPLA CLOUD are free of charge
*
*/
SuplaDevice.begin(GUID, // Global Unique Identifier
"192.168.1.6", // SUPLA server address
"pi@raspberrypi", // Email address used to login to Supla Cloud
AUTHKEY); // Authorization key
}
void loop() {
SuplaDevice.iterate();
}