Może niezbyt suplowo wygląda, ale działa
Do pełni szczęścia przydałoby się automatyczne generowanie GUID, bo trzeba zmieniać za każdą kompilacją (może użyć odczytanego MAC jako część GUID?)
[PORADNIK] Arduino IDE
Dodałem jeszcze linijkę żeby AP się wyłączyło jak już jest połączony z suplą.
Nie wiem czy w dobrym miejscu ale u mnie działa a jak kliknie się config to sieć się pojjawia
przydałoby się jeszcze ustawić wejście w cobfig po przytrzymaniu przycisku przez 10 s lub 10 kliknięć .
Nie wiem czy w dobrym miejscu ale u mnie działa a jak kliknie się config to sieć się pojjawia
Kod: Zaznacz cały
}
WiFi.softAPdisconnect(true); // wyłączenie rozgłaszania sieci ESP
} else {
Serial.println("failed to mount FS");
}
//end read
//Serial.println(Location_id);
//Serial.println(Location_Pass);
//Serial.println(Supla_server);
char GUID[SUPLA_GUID_SIZE] ={0x1
Ostatnio zmieniony ndz lip 08, 2018 9:19 pm przez wojtas567, łącznie zmieniany 1 raz.
Pozdrawiam
Wojtek
Wojtek
Aby uzyskać 10s wystarczy zamiast
wpisać
Kod: Zaznacz cały
int timeout = 120; // seconds to run for
Kod: Zaznacz cały
int timeout = 10000; // seconds to run for
TEORIA jest wtedy gdy wszystko wiemy i nic nie działa
PRAKTYKA jest wtedy gdy wszystko działa a my nie wiemy dlaczego
My łączymy teorię z praktyką czyli nic nie działa i nikt nie wie dlaczego
PRAKTYKA jest wtedy gdy wszystko działa a my nie wiemy dlaczego
My łączymy teorię z praktyką czyli nic nie działa i nikt nie wie dlaczego
jeśli masz rację
} else {
Serial.println("failed to mount FS");
}
//end read
//Serial.println(Location_id);
//Serial.println(Location_Pass);
//Serial.println(Supla_server);
WiFi.mode(WIFI_STA); // Force to station mode because if device was switched off while in access point mode it will start up next time in access point mode.
-------------
int timeout = 120; // seconds to run for
time this is the open configuration
if you reset AP is still open
} else {
Serial.println("failed to mount FS");
}
//end read
//Serial.println(Location_id);
//Serial.println(Location_Pass);
//Serial.println(Supla_server);
WiFi.mode(WIFI_STA); // Force to station mode because if device was switched off while in access point mode it will start up next time in access point mode.
-------------
int timeout = 120; // seconds to run for
time this is the open configuration
if you reset AP is still open
To chyba jest za mało bo u mnie nie działa , od razu wskakuje w tryb konfig AP.slawek pisze: ↑ndz lip 08, 2018 8:28 pm Aby uzyskać 10s wystarczy zamiastwpisaćKod: Zaznacz cały
int timeout = 120; // seconds to run for
Kod: Zaznacz cały
int timeout = 10000; // seconds to run for
Pozdrawiam
Wojtek
Wojtek
Faktycznie - działa natychmiast...
TEORIA jest wtedy gdy wszystko wiemy i nic nie działa
PRAKTYKA jest wtedy gdy wszystko działa a my nie wiemy dlaczego
My łączymy teorię z praktyką czyli nic nie działa i nikt nie wie dlaczego
PRAKTYKA jest wtedy gdy wszystko działa a my nie wiemy dlaczego
My łączymy teorię z praktyką czyli nic nie działa i nikt nie wie dlaczego
Dodałem do kodu jeszcze termometry i przycisk, ale nie kompiluje mi się. @Slawek, @wojtas567 mozecie zerknąć co jest nie tak?
Wywala mi sekcji void loop () na DynamicJsonBuffer jsonBuffer;
exit status 1
'DynamicJsonBuffer' was not declared in this scope
Wywala mi sekcji void loop () na DynamicJsonBuffer jsonBuffer;
exit status 1
'DynamicJsonBuffer' was not declared in this scope
Kod: Zaznacz cały
#include <FS.h>
#include <ESP8266WiFi.h>
#define SUPLADEVICE_CPP
#include <SuplaDevice.h>
#include <ESP8266WebServer.h>
#include <DNSServer.h>
#include <WiFiManager.h>
#include <ArduinoJson.h>
#include <OneWire.h>
#include <DallasTemperature.h>
int button1 = 0; //wartosc początkowa dla przycisku 1
WiFiClient client;
OneWire oneWire(4); // (D2) - Pin number
DallasTemperature sensors(&oneWire);
DeviceAddress garaz = { 0x28, 0xFF, 0x2E, 0xFB, 0xC1, 0x17, 0x1, 0xD3 }; // odczytany adres 28FF2EFBC11701D3
DeviceAddress zewnatrz = { 0x28, 0xFF, 0xEC, 0xFE, 0xC1, 0x17, 0x1, 0xF3 }; //Odczytany adres 28FFECFEC11701F3
//define your default values here, if there are different values in config.json, they are overwritten.
//length should be max size + 1
char Supla_server[40];
char Location_id[15];
char Location_Pass[20];
byte mac[6];
//flag for saving data
bool shouldSaveConfig = false;
bool initialConfig = false;
#define TRIGGER_PIN D3
int timeout = 120; // szas otwarica config po resecie ESP
int measurePin = A0;
int ledPower = 5;
int samplingTime = 280;
int deltaTime = 40;
int sleepTime = 9680;
float voMeasured = 0;
float calcVoltage = 0;
float dustDensity = 0;
//callback notifying us of the need to save config
void saveConfigCallback () {
Serial.println("Should save config");
shouldSaveConfig = true;
}
void ondemandwifiCallback () {
// The extra parameters to be configured (can be either global or just in the setup)
// After connecting, parameter.getValue() will get you the configured value
// id/name placeholder/prompt default length
WiFiManagerParameter custom_Supla_server("server", "supla server", Supla_server, 40);
WiFiManagerParameter custom_Location_id("ID", "Location_id", Location_id, 15);
WiFiManagerParameter custom_Location_Pass("Password", "Location_Pass", Location_Pass, 20);
//WiFiManager
//Local intialization. Once its business is done, there is no need to keep it around
WiFiManager wifiManager;
//set config save notify callback
wifiManager.setSaveConfigCallback(saveConfigCallback);
//add all your parameters here
wifiManager.addParameter(&custom_Supla_server);
wifiManager.addParameter(&custom_Location_id);
wifiManager.addParameter(&custom_Location_Pass);
//set minimu quality of signal so it ignores AP's under that quality
//defaults to 8%
wifiManager.setMinimumSignalQuality();
// set configportal timeout
wifiManager.setConfigPortalTimeout(timeout);
if (!wifiManager.startConfigPortal("OnDemandAP")) {
Serial.println("failed to connect and hit timeout");
delay(3000);
//reset and try again, or maybe put it to deep sleep
ESP.restart();
delay(5000);
}
//if you get here you have connected to the WiFi
Serial.println("connected...yeey :)");
//read updated parameters
strcpy(Supla_server, custom_Supla_server.getValue());
strcpy(Location_id, custom_Location_id.getValue());
strcpy(Location_Pass, custom_Location_Pass.getValue());
}
// DS18B20 Sensor read implementation
double get_temperature(int channelNumber, double last_val) {
digitalWrite(ledPower,LOW); // power on the LED
delayMicroseconds(samplingTime);
voMeasured = analogRead(measurePin); // read the dust value
delayMicroseconds(deltaTime);
digitalWrite(ledPower,HIGH); // turn the LED off
delayMicroseconds(sleepTime);
// 0 - 5.0V mapped to 0 - 1023 integer values
calcVoltage = voMeasured * (5.0 / 1024);
dustDensity = (0.17 * calcVoltage - 0.1)*1000;
Serial.print("Raw Signal Value (0-1023): ");
Serial.print(voMeasured);
Serial.print(" - Voltage: ");
Serial.print(calcVoltage);
Serial.print(" - Dust Density [ug/m3]: ");
Serial.println(dustDensity);
double t = -275;
if ( sensors.getDeviceCount() > 0 )
{
sensors.requestTemperatures();
switch(channelNumber)
{
case 0:
t = sensors.getTempC(garaz);
break;
case 1:
t = sensors.getTempC(zewnatrz);
break;
};
};
return t;
}
void setup() {
Serial.begin(115200);
//sensors.begin();
pinMode (16, INPUT_PULLUP); //ustawiamy Pin 16 (D0) na przycisk
// Init DS18B20 library
sensors.begin();
// Set temperature callback
SuplaDevice.setTemperatureCallback(&get_temperature);
pinMode(TRIGGER_PIN, INPUT);
if (WiFi.SSID()==""){
//Serial.println("We haven't got any access point credentials, so get them now");
initialConfig = true;
}
//read configuration from FS json
Serial.println("mounting FS...");
if (SPIFFS.begin()) {
Serial.println("mounted file system");
if (SPIFFS.exists("/config.json")) {
//file exists, reading and loading
Serial.println("reading config file");
File configFile = SPIFFS.open("/config.json", "r");
if (configFile) {
Serial.println("opened config file");
size_t size = configFile.size();
// Allocate a buffer to store contents of the file.
std::unique_ptr<char[]> buf(new char[size]);
configFile.readBytes(buf.get(), size);
DynamicJsonBuffer jsonBuffer;
JsonObject& json = jsonBuffer.parseObject(buf.get());
json.printTo(Serial);
if (json.success()) {
// Serial.println("\nparsed json");
strcpy(Supla_server, json["Supla_server"]);
strcpy(Location_id, json["Location_id"]);
strcpy(Location_Pass, json["Location_Pass"]);
} else {
Serial.println("failed to load json config");
}
}
}
WiFi.softAPdisconnect(true); // wyłączenie rozglaszania Wifi ESP po połaczeniu do lokalnego WIFI
} else {
Serial.println("failed to mount FS");
}
//end read
//Serial.println(Location_id);
//Serial.println(Location_Pass);
//Serial.println(Supla_server);
delay(10);
char GUID[SUPLA_GUID_SIZE] ={0x53,0x9C,0x2D,0x21,0x2F,0xB2,0xB9,0x40,0x71,0xAD,0xA8,0xCD,0x39,0xC7,0x34,0x4D};
// with GUID that you can retrieve from https://www.supla.org/arduino/get-guid.
WiFi.macAddress(mac);
// CHANNEL0 - Thermometer DS18B20
SuplaDevice.addDS18B20Thermometer();
// CHANNEL1 - Thermometer DS18B20
SuplaDevice.addDS18B20Thermometer();
// CHANNEL2 - RELAY
SuplaDevice.addRelay(D5, true);
// CHANNEL3 - RELAY
SuplaDevice.addRelay(D6, true);
// CHANNEL4 - RELAY
SuplaDevice.addRelay(D7, true);
// CHANNEL5 - Opening sensor (Normal Open)
SuplaDevice.addSensorNO(A0); // A0 - Pin number where the sensor is connected
// Call SuplaDevice.addSensorNO(A0, true) with an extra "true" parameter
// to enable the internal pull-up resistor
// CHANNEL6 - DHT22 Sensor
// SuplaDevice.addDHT11();
// SuplaDevice.addAM2302();
// SuplaDevice.addDHT22();
int LocationID = atoi(Location_id);
SuplaDevice.begin(GUID, // Global Unique Identifier
mac, // Ethernet MAC address
Supla_server, // SUPLA server address
LocationID, // Location ID
Location_Pass); // Location Password
}
void loop() {
// is configuration portal requested?
if ( digitalRead(TRIGGER_PIN) == LOW|| (initialConfig)) {
ondemandwifiCallback () ;
initialConfig = false;
}
//save the custom parameters to FS
if (shouldSaveConfig) {
Serial.println("saving config");
DynamicJsonBuffer jsonBuffer;
JsonObject& json = jsonBuffer.createObject();
json["Supla_server"] = Supla_server;
json["Location_id"] = Location_id;
json["Location_Pass"] = Location_Pass;
File configFile = SPIFFS.open("/config.json", "w");
if (!configFile) {
Serial.println("failed to open config file for writing");
}
json.prettyPrintTo(Serial);
json.printTo(configFile);
configFile.close();
Serial.println("config saved");
shouldSaveConfig = false;
//end save
}
if (WiFi.status() != WL_CONNECTED)
{
WiFi_up();
}
SuplaDevice.iterate();
TSD_SuplaChannelNewValue przycisk1; //ustaw nazwe dla przycisku
przycisk1.SenderID = 0; // Powiadom clouda, że załączasz recznie. W przypadku siłowników ma być 0
przycisk1.ChannelNumber = 4; // nr kanału przekaźnika
przycisk1.DurationMS = 0; //czas wlaczenia
button1 = digitalRead(16);
if(digitalRead(16)==LOW){ // tu dodajemy jeszcze raz zeby nie pstrykalo samo czyli przerwa i ponowne zapytanie
delay(100);
if(digitalRead(16)==LOW){
przycisk1.value[0] = !przycisk1.value[0];
SuplaDevice.channelSetValue(&przycisk1);
while(digitalRead(16)==LOW);
delay(20);
}
}}
}
// Supla.org ethernet layer
int supla_arduino_tcp_read(void *buf, int count) {
_supla_int_t size = client.available();
if ( size > 0 ) {
if ( size > count ) size = count;
return client.read((uint8_t *)buf, size);
};
return -1;
};
int supla_arduino_tcp_write(void *buf, int count) {
return client.write((const uint8_t *)buf, count);
};
bool supla_arduino_svr_connect(const char *server, int port) {
return client.connect(server, 2015);
}
bool supla_arduino_svr_connected(void) {
return client.connected();
}
void supla_arduino_svr_disconnect(void) {
client.stop();
}
void supla_arduino_eth_setup(uint8_t mac[6], IPAddress *ip) {
WiFi_up();
}
SuplaDeviceCallbacks supla_arduino_get_callbacks(void) {
SuplaDeviceCallbacks cb;
cb.tcp_read = &supla_arduino_tcp_read;
cb.tcp_write = &supla_arduino_tcp_write;
cb.eth_setup = &supla_arduino_eth_setup;
cb.svr_connected = &supla_arduino_svr_connected;
cb.svr_connect = &supla_arduino_svr_connect;
cb.svr_disconnect = &supla_arduino_svr_disconnect;
cb.get_temperature = &get_temperature;
cb.get_temperature_and_humidity = NULL;
cb.get_rgbw_value = NULL;
cb.set_rgbw_value = NULL;
return cb;
}
void WiFi_up() // Procedimiento de conexión para redes WiFi
{
Serial.print("Conexión a la red ");
// Serial.println(ssid);
WiFi.begin(); // Intentar conectarse a la red
for (int x = 60; x > 0; x--)
{
if (WiFi.status() == WL_CONNECTED)
{
break;
}
else
{
Serial.print(".");
delay(500);
}
}
if (WiFi.status() == WL_CONNECTED)
{
Serial.println("");
Serial.println("Conexión hecha");
Serial.println("Adres IP: ");
Serial.print(WiFi.localIP());
Serial.print(" / ");
Serial.println(WiFi.subnetMask());
Serial.print("puerta: ");
Serial.println(WiFi.gatewayIP());
long rssi = WiFi.RSSI();
Serial.print("Fuerza de la señal (RSSI): ");
Serial.print(rssi);
Serial.println(" dBm");
}
else
{
Serial.println("");
Serial.println("La conexión no pudo hacerse");
}
}
brakuje Ci biblioteki <ArduinoJson.h>
poprawiłem też termometry bo miałeś za dużo kodu chyba, że będziesz używał czujnika pyłu ale to i tak by nie działał jeszcze.
Kod: Zaznacz cały
#include <FS.h>
#include <ESP8266WiFi.h>
#define SUPLADEVICE_CPP
#include <SuplaDevice.h>
#include <ESP8266WebServer.h>
#include <DNSServer.h>
#include <WiFiManager.h>
#include <ArduinoJson.h>
#include <OneWire.h>
#include <DallasTemperature.h>
int button1 = 0; //wartosc początkowa dla przycisku 1
WiFiClient client;
OneWire oneWire(4); // (D2) - Pin number
DallasTemperature sensors(&oneWire);
DeviceAddress garaz = { 0x28, 0xFF, 0x2E, 0xFB, 0xC1, 0x17, 0x1, 0xD3 }; // odczytany adres 28FF2EFBC11701D3
DeviceAddress zewnatrz = { 0x28, 0xFF, 0xEC, 0xFE, 0xC1, 0x17, 0x1, 0xF3 }; //Odczytany adres 28FFECFEC11701F3
//define your default values here, if there are different values in config.json, they are overwritten.
//length should be max size + 1
char Supla_server[40];
char Location_id[15];
char Location_Pass[20];
byte mac[6];
//flag for saving data
bool shouldSaveConfig = false;
bool initialConfig = false;
#define TRIGGER_PIN D3
int timeout = 120; // szas otwarica config po resecie ESP
//callback notifying us of the need to save config
void saveConfigCallback () {
Serial.println("Should save config");
shouldSaveConfig = true;
}
void ondemandwifiCallback () {
// The extra parameters to be configured (can be either global or just in the setup)
// After connecting, parameter.getValue() will get you the configured value
// id/name placeholder/prompt default length
WiFiManagerParameter custom_Supla_server("server", "supla server", Supla_server, 40);
WiFiManagerParameter custom_Location_id("ID", "Location_id", Location_id, 15);
WiFiManagerParameter custom_Location_Pass("Password", "Location_Pass", Location_Pass, 20);
//WiFiManager
//Local intialization. Once its business is done, there is no need to keep it around
WiFiManager wifiManager;
//set config save notify callback
wifiManager.setSaveConfigCallback(saveConfigCallback);
//add all your parameters here
wifiManager.addParameter(&custom_Supla_server);
wifiManager.addParameter(&custom_Location_id);
wifiManager.addParameter(&custom_Location_Pass);
//set minimu quality of signal so it ignores AP's under that quality
//defaults to 8%
wifiManager.setMinimumSignalQuality();
// set configportal timeout
wifiManager.setConfigPortalTimeout(timeout);
if (!wifiManager.startConfigPortal("SuplaAP")) {
Serial.println("failed to connect and hit timeout");
delay(3000);
//reset and try again, or maybe put it to deep sleep
ESP.restart();
delay(5000);
}
//if you get here you have connected to the WiFi
Serial.println("connected...yeey :)");
//read updated parameters
strcpy(Supla_server, custom_Supla_server.getValue());
strcpy(Location_id, custom_Location_id.getValue());
strcpy(Location_Pass, custom_Location_Pass.getValue());
}
// DS18B20 Sensor read implementation
double get_temperature(int channelNumber, double last_val) {
double t = -275;
if ( sensors.getDeviceCount() > 0 )
{
sensors.requestTemperatures();
switch(channelNumber)
{
case 0:
t = sensors.getTempC(garaz);
break;
case 1:
t = sensors.getTempC(zewnatrz);
break;
};
};
return t;
}
void setup() {
Serial.begin(115200);
pinMode (16, INPUT_PULLUP); //ustawiamy Pin 16 (D0) na przycisk
// Init DS18B20 library
sensors.begin();
// Set temperature callback
SuplaDevice.setTemperatureCallback(&get_temperature);
pinMode(TRIGGER_PIN, INPUT);
if (WiFi.SSID()==""){
//Serial.println("We haven't got any access point credentials, so get them now");
initialConfig = true;
}
//read configuration from FS json
Serial.println("mounting FS...");
if (SPIFFS.begin()) {
Serial.println("mounted file system");
if (SPIFFS.exists("/config.json")) {
//file exists, reading and loading
Serial.println("reading config file");
File configFile = SPIFFS.open("/config.json", "r");
if (configFile) {
Serial.println("opened config file");
size_t size = configFile.size();
// Allocate a buffer to store contents of the file.
std::unique_ptr<char[]> buf(new char[size]);
configFile.readBytes(buf.get(), size);
DynamicJsonBuffer jsonBuffer;
JsonObject& json = jsonBuffer.parseObject(buf.get());
json.printTo(Serial);
if (json.success()) {
// Serial.println("\nparsed json");
strcpy(Supla_server, json["Supla_server"]);
strcpy(Location_id, json["Location_id"]);
strcpy(Location_Pass, json["Location_Pass"]);
} else {
Serial.println("failed to load json config");
}
}
}
WiFi.softAPdisconnect(true); // wyłączenie rozglaszania Wifi ESP po połaczeniu do lokalnego WIFI
} else {
Serial.println("failed to mount FS");
}
//end read
//Serial.println(Location_id);
//Serial.println(Location_Pass);
//Serial.println(Supla_server);
delay(10);
char GUID[SUPLA_GUID_SIZE] ={0x53,0x9C,0x2D,0x21,0x2F,0xB2,0xB9,0x40,0x71,0xAD,0xA8,0xCD,0x39,0xC7,0x34,0x4D};
// with GUID that you can retrieve from https://www.supla.org/arduino/get-guid.
WiFi.macAddress(mac);
// CHANNEL0 - Thermometer DS18B20
SuplaDevice.addDS18B20Thermometer();
// CHANNEL1 - Thermometer DS18B20
SuplaDevice.addDS18B20Thermometer();
// CHANNEL2 - RELAY
SuplaDevice.addRelay(D5, true);
// CHANNEL3 - RELAY
SuplaDevice.addRelay(D6, true);
// CHANNEL4 - RELAY
SuplaDevice.addRelay(D7, true);
// CHANNEL5 - Opening sensor (Normal Open)
SuplaDevice.addSensorNO(A0); // A0 - Pin number where the sensor is connected
// Call SuplaDevice.addSensorNO(A0, true) with an extra "true" parameter
// to enable the internal pull-up resistor
// CHANNEL6 - DHT22 Sensor
// SuplaDevice.addDHT11();
// SuplaDevice.addAM2302();
// SuplaDevice.addDHT22();
int LocationID = atoi(Location_id);
SuplaDevice.begin(GUID, // Global Unique Identifier
mac, // Ethernet MAC address
Supla_server, // SUPLA server address
LocationID, // Location ID
Location_Pass); // Location Password
}
void loop() {
// is configuration portal requested?
if ( digitalRead(TRIGGER_PIN) == LOW|| (initialConfig)) {
ondemandwifiCallback () ;
initialConfig = false;
}
//save the custom parameters to FS
if (shouldSaveConfig) {
Serial.println("saving config");
DynamicJsonBuffer jsonBuffer;
JsonObject& json = jsonBuffer.createObject();
json["Supla_server"] = Supla_server;
json["Location_id"] = Location_id;
json["Location_Pass"] = Location_Pass;
File configFile = SPIFFS.open("/config.json", "w");
if (!configFile) {
Serial.println("failed to open config file for writing");
}
json.prettyPrintTo(Serial);
json.printTo(configFile);
configFile.close();
Serial.println("config saved");
shouldSaveConfig = false;
//end save
}
if (WiFi.status() != WL_CONNECTED)
{
WiFi_up();
}
SuplaDevice.iterate();
TSD_SuplaChannelNewValue przycisk1; //ustaw nazwe dla przycisku
przycisk1.SenderID = 0; // Powiadom clouda, że załączasz recznie. W przypadku siłowników ma być 0
przycisk1.ChannelNumber = 4; // nr kanału przekaźnika
przycisk1.DurationMS = 0; //czas wlaczenia
button1 = digitalRead(16);
if(digitalRead(16)==LOW){ // tu dodajemy jeszcze raz zeby nie pstrykalo samo czyli przerwa i ponowne zapytanie
delay(100);
if(digitalRead(16)==LOW){
przycisk1.value[0] = !przycisk1.value[0];
SuplaDevice.channelSetValue(&przycisk1);
while(digitalRead(16)==LOW);
delay(20);
}
}
}
// Supla.org ethernet layer
int supla_arduino_tcp_read(void *buf, int count) {
_supla_int_t size = client.available();
if ( size > 0 ) {
if ( size > count ) size = count;
return client.read((uint8_t *)buf, size);
};
return -1;
};
int supla_arduino_tcp_write(void *buf, int count) {
return client.write((const uint8_t *)buf, count);
};
bool supla_arduino_svr_connect(const char *server, int port) {
return client.connect(server, 2015);
}
bool supla_arduino_svr_connected(void) {
return client.connected();
}
void supla_arduino_svr_disconnect(void) {
client.stop();
}
void supla_arduino_eth_setup(uint8_t mac[6], IPAddress *ip) {
WiFi_up();
}
SuplaDeviceCallbacks supla_arduino_get_callbacks(void) {
SuplaDeviceCallbacks cb;
cb.tcp_read = &supla_arduino_tcp_read;
cb.tcp_write = &supla_arduino_tcp_write;
cb.eth_setup = &supla_arduino_eth_setup;
cb.svr_connected = &supla_arduino_svr_connected;
cb.svr_connect = &supla_arduino_svr_connect;
cb.svr_disconnect = &supla_arduino_svr_disconnect;
cb.get_temperature = &get_temperature;
cb.get_temperature_and_humidity = NULL;
cb.get_rgbw_value = NULL;
cb.set_rgbw_value = NULL;
return cb;
}
void WiFi_up() // Procedimiento de conexión para redes WiFi
{
Serial.print("Conexión a la red ");
// Serial.println(ssid);
WiFi.begin(); // Intentar conectarse a la red
for (int x = 60; x > 0; x--)
{
if (WiFi.status() == WL_CONNECTED)
{
break;
}
else
{
Serial.print(".");
delay(500);
}
}
if (WiFi.status() == WL_CONNECTED)
{
Serial.println("");
Serial.println("Conexión hecha");
Serial.println("Adres IP: ");
Serial.print(WiFi.localIP());
Serial.print(" / ");
Serial.println(WiFi.subnetMask());
Serial.print("puerta: ");
Serial.println(WiFi.gatewayIP());
long rssi = WiFi.RSSI();
Serial.print("Fuerza de la señal (RSSI): ");
Serial.print(rssi);
Serial.println(" dBm");
}
else
{
Serial.println("");
Serial.println("La conexión no pudo hacerse");
}
}
Pozdrawiam
Wojtek
Wojtek