SONOFF

gaurav
Posts: 82
Joined: Mon May 08, 2017 9:49 am

Re: SONOFF

Post by gaurav » Mon May 14, 2018 12:14 pm

Can anybody tell me?

User avatar
pzygmunt
Posts: 3861
Joined: Tue Jan 19, 2016 9:26 am
Location: Paczków
Contact:

Re: SONOFF

Post by pzygmunt » Mon May 14, 2018 12:25 pm

GPIO 15 should be pulled down to the GND.
You should properly set/init this port on boot.

gaurav
Posts: 82
Joined: Mon May 08, 2017 9:49 am

Re: SONOFF

Post by gaurav » Tue May 15, 2018 10:03 am

I've connected GPIO15 to GND via 10K resistor.
Problem is same.

User avatar
pzygmunt
Posts: 3861
Joined: Tue Jan 19, 2016 9:26 am
Location: Paczków
Contact:

Re: SONOFF

Post by pzygmunt » Tue May 15, 2018 10:08 am

"You should properly set/init this port on boot."

gaurav
Posts: 82
Joined: Mon May 08, 2017 9:49 am

Re: SONOFF

Post by gaurav » Mon May 28, 2018 1:26 pm

I am trying to flash Sonoff Socket firmware in Sonoff Basic R2 module. Flashing shows success but there is no ssid broadcast no led blinking and garbage values on putty Baudrate used on putty 74880 and 115200.

config

boot file address 0x00000
sonoff socket firmware 0x01000
esp_int 0xFC000
flash size 1 MB
baud rate 115200
SPI speed 40MHz
SPI Mode DOUT

USB to TTL device used "PL2303" and "arduino uno as USB to TTL".

Tools used to flash "Nodemcu firmware programmer" and "ESP flash download tool". What could be the problem? Am I missing anything?

gaurav
Posts: 82
Joined: Mon May 08, 2017 9:49 am

Re: SONOFF

Post by gaurav » Tue May 29, 2018 8:59 am

Can anyone help me. I am pressing the GPIO 0 button before powering up the Sonoff Basic R2 to enter it into flash mode. Never had this problem earlier.

User avatar
pzygmunt
Posts: 3861
Joined: Tue Jan 19, 2016 9:26 am
Location: Paczków
Contact:

Re: SONOFF

Post by pzygmunt » Tue May 29, 2018 12:45 pm

Connect Putty.
Turn on the device and check logs.

gaurav
Posts: 82
Joined: Mon May 08, 2017 9:49 am

Re: SONOFF

Post by gaurav » Tue May 29, 2018 1:23 pm

I connected to putty with two baudrates 74880 and 115200.
Attachments
putty.png
putty with baudrate 115200
putty.png (15.78 KiB) Viewed 196 times
putty(74880).png
putty with baudrate 74880
putty(74880).png (52.8 KiB) Viewed 196 times

User avatar
pzygmunt
Posts: 3861
Joined: Tue Jan 19, 2016 9:26 am
Location: Paczków
Contact:

Re: SONOFF

Post by pzygmunt » Tue May 29, 2018 1:29 pm

Connect USB GND with GND on BOARD

gaurav
Posts: 82
Joined: Mon May 08, 2017 9:49 am

Re: SONOFF

Post by gaurav » Tue May 29, 2018 1:31 pm

usb gnd is connected to the board.

Post Reply