Próbuję przejść z Ethernet Shield na ENC28J60 niestety bezskutecznie
Elektrycznie wszystko raczej dobrze podłączone bo z debug-ów widzę że pobiera adres IP, jednak na tym się kończy.
Nie mogę w żaden sposób podłączyć się do serwera. Poniżej mój kod, a w zasadzie to gotowy przykład. Dokładnie ten sam kod z podłączoną biblioteką dla Shield-a działa poprawnie. Rejestruje się na serwerze. Za każdym razem usuwałem urządzenie z serwera.
Kod: Zaznacz cały
/*
Copyright (C) AC SOFTWARE SP. Z O.O.
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
as published by the Free Software Foundation; either version 2
of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
*/
#include <UIPEthernet.h>
#include <SuplaDevice.h>
/*
* This example requires UIPEthernet library installed.
* https://github.com/ntruchsess/arduino_uip
*/
void setup() {
Serial.begin(9600);
// Replace the falowing GUID
char GUID[SUPLA_GUID_SIZE] = {};
// with GUID that you can retrieve from https://www.supla.org/arduino/get-guid
// Ethernet MAC address
uint8_t mac[6] = {0x00, 0x01, 0x02, 0x03, 0x04, 0x05};
/*
* Having your device already registered at cloud.supla.org,
* you want to change CHANNEL sequence or remove any of them,
* then you must also remove the device itself from cloud.supla.org.
* Otherwise you will get "Channel conflict!" error.
*/
// CHANNEL0 - RELAY
SuplaDevice.addRelay(44); // 44 - Pin number where the relay is connected
// Call SuplaDevice.addRelay(44, true) with an extra "true" parameter
// to enable "port value inversion"
// where HIGH == LOW, and LOW == HIGH
// CHANNEL1 - RELAY
SuplaDevice.addRelay(45); // 45 - Pin number where the relay is connected
// CHANNEL3 - TWO RELAYS (Roller shutter operation)
SuplaDevice.addRollerShutterRelays(46, // 46 - Pin number where the 1st relay is connected
47); // 47 - Pin number where the 2nd relay is connected
// CHANNEL4 - Opening sensor (Normal Open)
SuplaDevice.addSensorNO(A0); // A0 - Pin number where the sensor is connected
// Call SuplaDevice.addSensorNO(A0, true) with an extra "true" parameter
// to enable the internal pull-up resistor
// CHANNEL5 - Opening sensor (Normal Open)
SuplaDevice.addSensorNO(A1); // A1 - Pin number where the sensor is connected
/*
* SuplaDevice Initialization.
* Server address, LocationID and LocationPassword are available at https://cloud.supla.org
* If you do not have an account, you can create it at https://cloud.supla.org/account/create
* SUPLA and SUPLA CLOUD are free of charge
*
*/
SuplaDevice.begin(GUID, // Global Unique Identifier
mac, // Ethernet MAC address
"svr11.supla.org", // SUPLA server address
xxx, // Location ID
"yyyy"); // Location Password
}
void loop() {
SuplaDevice.iterate();
}