Sonoff Basic + Arduino

Post Reply
Asica10
Posts: 52
Joined: Thu Feb 28, 2019 8:12 pm

Wed Jul 24, 2019 6:37 pm

Witam.


Próbuje wgrać do Sonoffa Basic kod za pomocą Arduino IDE i mam problem ktorego nie potrafie przeskoczyć.

Wgrywanie softu dla Wemosa czy Esp01 za pomocą Arduino IDE działa jak należy, a z Sonoffem Basic mam problem.

Sciągnołem najnowsze biblioteki i wykorzystałem najprostszy gotowy przykład dokładając swoje dane sieci by sprawdzić czy zadziała (program się wgrywa ale nie łączy się ESP do routera, a co do piero do supli)

Code: Select all

/**
 * Supla.org NodeMCU WiFi minimal example
 * Author: Programistyk - Kamil Kaminski <kamil@programistyk.pl>
 * 
 * This example shows how to configure SuplaDevice for building for NodeMCU within Arduino IDE
 */


#include <srpc.h>
#include <log.h>
#include <eh.h>
#include <proto.h>
#include <IEEE754tools.h>
// We define our own ethernet layer
#define SUPLADEVICE_CPP
#include <SuplaDevice.h>
#include <lck.h>

#include <WiFiClient.h>
#include <ESP8266WiFiType.h>
#include <ESP8266WiFi.h>
#include <ESP8266WiFiScan.h>
#include <ESP8266WiFiMulti.h>
#include <WiFiServer.h>
#include <ESP8266WiFiGeneric.h>
#include <WiFiClientSecure.h>
#include <ESP8266WiFiAP.h>
#include <ESP8266WiFiSTA.h>
#include <WiFiUdp.h>

WiFiClient client;

// Setup Supla connection
const char* ssid     = "xxx";
const char* password = "xxx";

void setup() {
  Serial.begin(115200);
  delay(10);

  // Replace the falowing GUID
  char GUID[SUPLA_GUID_SIZE] = {0xCB,0xB4,0x93,0x22,0xC9,0xE8,0xF6,0xB6,0xB7,0xA5,0x3E,0x9F,0xFB,0x4B,0x7A,0xEF};
  // with GUID that you can retrieve from https://www.supla.org/arduino/get-guid

  // Ethernet MAC address
  uint8_t mac[6] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00};

  /*
   * Having your device already registered at cloud.supla.org,
   * you want to change CHANNEL sequence or remove any of them,
   * then you must also remove the device itself from cloud.supla.org.
   * Otherwise you will get "Channel conflict!" error.
   */
    
  // CHANNEL0 - RELAY
  SuplaDevice.addRelay(10, true);           // 44 - Pin number where the relay is connected      
                                      // Call SuplaDevice.addRelay(44, true) with an extra "true" parameter 
                                      // to enable "port value inversion"
                                      // where HIGH == LOW, and LOW == HIGH   

  // CHANNEL1 - RELAY
 // SuplaDevice.addRelay(45, true);           // 45 - Pin number where the relay is connected   

  // CHANNEL3 - TWO RELAYS (Roller shutter operation)
  //SuplaDevice.addRollerShutterRelays(46,     // 46 - Pin number where the 1st relay is connected   
//                                     47, true);    // 47 - Pin number where the 2nd relay is connected  

  // CHANNEL4 - Opening sensor (Normal Open)
  //SuplaDevice.addSensorNO(A0); // A0 - Pin number where the sensor is connected
                               // Call SuplaDevice.addSensorNO(A0, true) with an extra "true" parameter
                               // to enable the internal pull-up resistor


  // CHANNEL5 - Opening sensor (Normal Open)
  //SuplaDevice.addSensorNO(A1); // A1 - Pin number where the sensor is connected


  // CHANNEL6 - DHT22 Sensor
  // SuplaDevice.addDHT11();
  // SuplaDevice.addAM2302();
  // SuplaDevice.addDHT22();

  SuplaDevice.begin(GUID,              // Global Unique Identifier 
                    mac,               // Ethernet MAC address
                    "svr12.supla.org",  // SUPLA server address
                    0,                 // Location ID 
                    "xx");               // Location Password

}

void loop() {
  SuplaDevice.iterate();
}

// Supla.org ethernet layer
    int supla_arduino_tcp_read(void *buf, int count) {
        _supla_int_t size = client.available();
       
        if ( size > 0 ) {
            if ( size > count ) size = count;
            return client.read((uint8_t *)buf, size);
        };
    
        return -1;
    };
    
    int supla_arduino_tcp_write(void *buf, int count) {
        return client.write((const uint8_t *)buf, count);
    };
    
    bool supla_arduino_svr_connect(const char *server, int port) {
          return client.connect(server, 2015);
    }
    
    bool supla_arduino_svr_connected(void) {
          return client.connected();
    }
    
    void supla_arduino_svr_disconnect(void) {
         client.stop();
    }
    
    void supla_arduino_eth_setup(uint8_t mac[6], IPAddress *ip) {

       // Serial.println("WiFi init");
        WiFi.begin(ssid, password);

        while (WiFi.status() != WL_CONNECTED) {
            delay(500);
        //    Serial.print(".");
        }

        //Serial.print("\nlocalIP: ");
        //Serial.println(WiFi.localIP());
        //Serial.print("subnetMask: ");
        //Serial.println(WiFi.subnetMask());
        //Serial.print("gatewayIP: ");
        //Serial.println(WiFi.gatewayIP());
    }

SuplaDeviceCallbacks supla_arduino_get_callbacks(void) {
          SuplaDeviceCallbacks cb;
          
          cb.tcp_read = &supla_arduino_tcp_read;
          cb.tcp_write = &supla_arduino_tcp_write;
          cb.eth_setup = &supla_arduino_eth_setup;
          cb.svr_connected = &supla_arduino_svr_connected;
          cb.svr_connect = &supla_arduino_svr_connect;
          cb.svr_disconnect = &supla_arduino_svr_disconnect;
          cb.get_temperature = NULL;
          cb.get_temperature_and_humidity = NULL;
          cb.get_rgbw_value = NULL;
          cb.set_rgbw_value = NULL;
          
          return cb;
}

Ustawienia w Arduino mam takie:

Image


Dodam że SonOff jesr sprawny ponieważ ogotwe binarki działają bez problemu




Prosze Was o pomoc.
vajera
Posts: 179
Joined: Wed Oct 31, 2018 7:58 am

Wed Jul 24, 2019 6:48 pm

A co masz na porcie szeregowym?
Patryk
Posts: 448
Joined: Mon Jan 07, 2019 7:51 pm

Wed Jul 24, 2019 8:36 pm

Asica10 wrote:
Wed Jul 24, 2019 6:37 pm
Witam.


Próbuje wgrać do Sonoffa Basic kod za pomocą Arduino IDE i mam problem ktorego nie potrafie przeskoczyć.

Wgrywanie softu dla Wemosa czy Esp01 za pomocą Arduino IDE działa jak należy, a z Sonoffem Basic mam problem.

Sciągnołem najnowsze biblioteki i wykorzystałem najprostszy gotowy przykład dokładając swoje dane sieci by sprawdzić czy zadziała (program się wgrywa ale nie łączy się ESP do routera, a co do piero do supli)

Code: Select all

/**
 * Supla.org NodeMCU WiFi minimal example
 * Author: Programistyk - Kamil Kaminski <kamil@programistyk.pl>
 * 
 * This example shows how to configure SuplaDevice for building for NodeMCU within Arduino IDE
 */


#include <srpc.h>
#include <log.h>
#include <eh.h>
#include <proto.h>
#include <IEEE754tools.h>
// We define our own ethernet layer
#define SUPLADEVICE_CPP
#include <SuplaDevice.h>
#include <lck.h>

#include <WiFiClient.h>
#include <ESP8266WiFiType.h>
#include <ESP8266WiFi.h>
#include <ESP8266WiFiScan.h>
#include <ESP8266WiFiMulti.h>
#include <WiFiServer.h>
#include <ESP8266WiFiGeneric.h>
#include <WiFiClientSecure.h>
#include <ESP8266WiFiAP.h>
#include <ESP8266WiFiSTA.h>
#include <WiFiUdp.h>

WiFiClient client;

// Setup Supla connection
const char* ssid     = "xxx";
const char* password = "xxx";

void setup() {
  Serial.begin(115200);
  delay(10);

  // Replace the falowing GUID
  char GUID[SUPLA_GUID_SIZE] = {0xCB,0xB4,0x93,0x22,0xC9,0xE8,0xF6,0xB6,0xB7,0xA5,0x3E,0x9F,0xFB,0x4B,0x7A,0xEF};
  // with GUID that you can retrieve from https://www.supla.org/arduino/get-guid

  // Ethernet MAC address
  uint8_t mac[6] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00};

  /*
   * Having your device already registered at cloud.supla.org,
   * you want to change CHANNEL sequence or remove any of them,
   * then you must also remove the device itself from cloud.supla.org.
   * Otherwise you will get "Channel conflict!" error.
   */
    
  // CHANNEL0 - RELAY
  SuplaDevice.addRelay(10, true);           // 44 - Pin number where the relay is connected      
                                      // Call SuplaDevice.addRelay(44, true) with an extra "true" parameter 
                                      // to enable "port value inversion"
                                      // where HIGH == LOW, and LOW == HIGH   

  // CHANNEL1 - RELAY
 // SuplaDevice.addRelay(45, true);           // 45 - Pin number where the relay is connected   

  // CHANNEL3 - TWO RELAYS (Roller shutter operation)
  //SuplaDevice.addRollerShutterRelays(46,     // 46 - Pin number where the 1st relay is connected   
//                                     47, true);    // 47 - Pin number where the 2nd relay is connected  

  // CHANNEL4 - Opening sensor (Normal Open)
  //SuplaDevice.addSensorNO(A0); // A0 - Pin number where the sensor is connected
                               // Call SuplaDevice.addSensorNO(A0, true) with an extra "true" parameter
                               // to enable the internal pull-up resistor


  // CHANNEL5 - Opening sensor (Normal Open)
  //SuplaDevice.addSensorNO(A1); // A1 - Pin number where the sensor is connected


  // CHANNEL6 - DHT22 Sensor
  // SuplaDevice.addDHT11();
  // SuplaDevice.addAM2302();
  // SuplaDevice.addDHT22();

  SuplaDevice.begin(GUID,              // Global Unique Identifier 
                    mac,               // Ethernet MAC address
                    "svr12.supla.org",  // SUPLA server address
                    0,                 // Location ID 
                    "xx");               // Location Password

}

void loop() {
  SuplaDevice.iterate();
}

// Supla.org ethernet layer
    int supla_arduino_tcp_read(void *buf, int count) {
        _supla_int_t size = client.available();
       
        if ( size > 0 ) {
            if ( size > count ) size = count;
            return client.read((uint8_t *)buf, size);
        };
    
        return -1;
    };
    
    int supla_arduino_tcp_write(void *buf, int count) {
        return client.write((const uint8_t *)buf, count);
    };
    
    bool supla_arduino_svr_connect(const char *server, int port) {
          return client.connect(server, 2015);
    }
    
    bool supla_arduino_svr_connected(void) {
          return client.connected();
    }
    
    void supla_arduino_svr_disconnect(void) {
         client.stop();
    }
    
    void supla_arduino_eth_setup(uint8_t mac[6], IPAddress *ip) {

       // Serial.println("WiFi init");
        WiFi.begin(ssid, password);

        while (WiFi.status() != WL_CONNECTED) {
            delay(500);
        //    Serial.print(".");
        }

        //Serial.print("\nlocalIP: ");
        //Serial.println(WiFi.localIP());
        //Serial.print("subnetMask: ");
        //Serial.println(WiFi.subnetMask());
        //Serial.print("gatewayIP: ");
        //Serial.println(WiFi.gatewayIP());
    }

SuplaDeviceCallbacks supla_arduino_get_callbacks(void) {
          SuplaDeviceCallbacks cb;
          
          cb.tcp_read = &supla_arduino_tcp_read;
          cb.tcp_write = &supla_arduino_tcp_write;
          cb.eth_setup = &supla_arduino_eth_setup;
          cb.svr_connected = &supla_arduino_svr_connected;
          cb.svr_connect = &supla_arduino_svr_connect;
          cb.svr_disconnect = &supla_arduino_svr_disconnect;
          cb.get_temperature = NULL;
          cb.get_temperature_and_humidity = NULL;
          cb.get_rgbw_value = NULL;
          cb.set_rgbw_value = NULL;
          
          return cb;
}

Ustawienia w Arduino mam takie:

Image


Dodam że SonOff jesr sprawny ponieważ ogotwe binarki działają bez problemu




Prosze Was o pomoc.
Obecne  sonoff-y basic mają ESP8285, a widzę, że próbujesz wgrać to do ESP8266.
Zobacz:
viewtopic.php?p=44308#p44308
Asica10
Posts: 52
Joined: Thu Feb 28, 2019 8:12 pm

Thu Jul 25, 2019 4:40 am

Moj sonoff jest na 8266. Znalazłem rozwiązanie w ustawiniach Arduino powinno być: Crystal Frequency 26MHz. Po zmianie tego parametru wszystko sie wgrywa bez problemu.
Post Reply