krycha88 pisze: ↑pt sty 27, 2023 2:28 pm
bokk pisze: ↑pt sty 27, 2023 1:54 pm
A jaki parametr ustawić dla warunkowania dla stanu gpio dla krańcówek. Dałem 2 warunki: warunek 1, przekaźnik 1, sensor krańcówka 1, stan gpio załącz ??, warunek 2, przekaźnik 1, sensor krańcówka 2, stan gpio wyłącz ??,
Pokaż co wyświetla się na uart przy starcie ESP.
Czy o to chodzi (2-8 wykasowałem)
> log
ets Jan 8 2013,rst cause:2, boot mode:(3,7)
load 0x4010f000, len 3460, room 16
tail 4
chksum 0xcc
load 0x3fff20b8, len 40, room 4
tail 4
chksum 0xc9
csum 0xc9
v0008e760
~ld
Config read
Key: 0 Value: 퓮 '* [
Key: 1 Value: 0 }謨BLHhMM,
Key: 2 Value: xx
Key: 3 Value: xx
Key: 4 Value: xx
Key: 5 Value: xx
Key: 6 Value: xx
Key: 7 Value: xx
Key: 8 Value: xx
Key: 9 Value: 1
Key: 10 Value:
Key: 11 Value: 2
Key: 12 Value:
Key: 13 Value:
Key: 14 Value:
Key: 15 Value:
Key: 16 Value:
Key: 17 Value:
Key: 18 Value:
Key: 19 Value:
Key: 20 Value:
Key: 21 Value: 1
Key: 22 Value:
Key: 23 Value:
Key: 24 Value: ,,,,,,,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 25 Value:
Key: 26 Value: ,,0,,,,,,,,,,,,,,,1,,,,,,,,,,,,,,,,,
Key: 27 Value:
Key: 28 Value:
Key: 29 Value: 1,1,0,,2,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 30 Value:
Key: 31 Value:
Key: 32 Value:
Key: 33 Value:
Key: 34 Value:
Key: 35 Value:
Key: 36 Value: 2,3,,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 37 Value:
Key: 38 Value: 1,3,,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 39 Value:
Key: 40 Value:
Key: 41 Value:
Key: 42 Value:
Key: 43 Value:
Key: 44 Value:
Key: 45 Value:
Key: 46 Value:
Key: 47 Value:
Key: 48 Value:
Key: 49 Value: 21,21,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 50 Value: 10,10,,,,,,,,,,,,
Key: 51 Value: ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 52 Value: ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 53 Value:
Key: 54 Value:
Key: 55 Value:
Key: 56 Value:
Key: 57 Value:
Key: 58 Value: 1
Key: 59 Value: 0
Key: 60 Value:
Key: 61 Value:
Key: 62 Value:
Key: 63 Value:
Key: 64 Value: 0,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 65 Value:
Key: 66 Value:
Key: 67 Value:
Key: 68 Value:
Key: 69 Value:
Key: 70 Value:
Key: 71 Value:
Key: 72 Value:
Key: 73 Value:
Key: 74 Value:
Key: 75 Value:
Key: 76 Value:
Key: 77 Value:
Key: 78 Value:
Key: 79 Value:
Key: 80 Value: 0
Key: 81 Value:
Key: 82 Value:
Key: 83 Value:
Key: 84 Value:
Key: 85 Value:
Key: 86 Value: 0,0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 87 Value: 0,0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 88 Value: 2
addConditionsElement:functionClient: 0, nrClient: 0, functionSensor: 21, nrSensor : 0
addConditionsElement:functionClient: 0, nrClient: 0, functionSensor: 21, nrSensor : 1
addConditionsExecutive: functionClient: 0, nrClient: 0
addConditionsExecutive: functionClient: 0, nrClient: 0
addConditionsSensor: functionSensor: 21, nrSensor : 0
addConditionsSensor: functionSensor: 21, nrSensor : 1
Supla - starting initialization
Storage initialization
readStorage: 8; Read: [53 55 50 4C 41 1 0 1 ]
Storage: Number of sections 1
Reading section: 0
readStorage: 7; Read: [3 5 0 24 0 24 0 ]
Section type: 3; size: 5
CRC1 36, CRC2 36, CRC calc 36
Config storage not configured
Validating storage state section with current device configuration
Storage state section validation completed. Loading elements state...
readStorage: 4; Read: [0 0 0 0 ]
Relay[0]: restored durationMs: 0
readStorage: 1; Read: [0 ]
Relay[0]: restored relay state: OFF
Relay[0] turn OFF (duration 0 ms)
**** Digital write[0], gpio: 5; value 1
Relay[0] turn OFF (duration 0 ms)
**** Digital write[0], gpio: 5; value 1
Channel(1) value changed to 1
Channel(2) value changed to 1
Initializing network layer
Network AP/hostname: WEMOS-D1-MINI-58BF25DA058E
Using Supla protocol version 16
Current status: [5] SuplaDevice initialized
Enter normal mode
WiFi: establishing connection with SSID: "Wireless"
Connected BSSID: 54:AF:97:E0:08:20
local IP: 192.168.1.142
subnetMask: 255.255.255.0
gatewayIP: 192.168.1.1
Signal strength (RSSI): -44 dBm
IMPROV
IMPROVhttp://192.168.1.142
Establishing NOT encrypted connection with: svr12.supla.org (port: 2015)
Connected to Supla Server
Current status: [10] Register in progress
Device registered (activity timeout 120 s, server version: 19, server min version: 1)
Current status: [17] Registered and ready
Changing activity timeout to 30
Activity timeout set to 30 s