Can i use this?
https://allegro.pl/oferta/modul-czujnik ... 0175030423
Supla universal IR emitter for 8 codes
- klimasstudio
- Posts: 1115
- Joined: Wed Aug 28, 2019 9:35 pm
- Location: localhost
- Contact:
Więc chodź OSUPLUJE Ci dom
Druk 3D - > https://klimastech.eu.org/druk-3d
Druk 3D - > https://klimastech.eu.org/druk-3d
you can't use that.klimasstudio wrote: ↑Sat Nov 13, 2021 12:28 pm Can i use this?
https://allegro.pl/oferta/modul-czujnik ... 0175030423
You need an IR receiver such as "TL1838" and an IR Led diode for the transmitter.
- klimasstudio
- Posts: 1115
- Joined: Wed Aug 28, 2019 9:35 pm
- Location: localhost
- Contact:
Ok i know. Parts from screen plus IR 940nm transmitancję diode from pilot.
Więc chodź OSUPLUJE Ci dom
Druk 3D - > https://klimastech.eu.org/druk-3d
Druk 3D - > https://klimastech.eu.org/druk-3d
something like this https://en-forum.supla.org/viewtopic.php?p=83319#p83319
As i understand,that software works on the devices connected to same device and not on other devices that can be linked through direct link.elmaya wrote: ↑Wed Nov 17, 2021 5:24 pmsomething like this https://en-forum.supla.org/viewtopic.php?p=83319#p83319
- klimasstudio
- Posts: 1115
- Joined: Wed Aug 28, 2019 9:35 pm
- Location: localhost
- Contact:
I have a problem with the operation of the board. The page takes a long time to load, half or not at all. Resetting the board causes it to lose WIFI settings.
Więc chodź OSUPLUJE Ci dom
Druk 3D - > https://klimastech.eu.org/druk-3d
Druk 3D - > https://klimastech.eu.org/druk-3d
have you used the version of this post? https://en-forum.supla.org/viewtopic.php?p=90457#p90457klimasstudio wrote: ↑Fri Nov 19, 2021 2:10 pm I have a problem with the operation of the board. The page takes a long time to load, half or not at all. Resetting the board causes it to lose WIFI settings.
- klimasstudio
- Posts: 1115
- Joined: Wed Aug 28, 2019 9:35 pm
- Location: localhost
- Contact:
I use version from 1st post. I want recive codes from pilot and send codes to tv/amp reciver. Want use only diodes to tx and rx codeselmaya wrote: ↑Fri Nov 19, 2021 2:23 pmhave you used the version of this post? https://en-forum.supla.org/viewtopic.php?p=90457#p90457klimasstudio wrote: ↑Fri Nov 19, 2021 2:10 pm I have a problem with the operation of the board. The page takes a long time to load, half or not at all. Resetting the board causes it to lose WIFI settings.
Więc chodź OSUPLUJE Ci dom
Druk 3D - > https://klimastech.eu.org/druk-3d
Druk 3D - > https://klimastech.eu.org/druk-3d
- klimasstudio
- Posts: 1115
- Joined: Wed Aug 28, 2019 9:35 pm
- Location: localhost
- Contact:
I testet this:
https://en-forum.supla.org/viewtopic.php?p=66208#p66208
and this...
https://en-forum.supla.org/viewtopic.php?p=66412#p66412
and have same problems. I try flashing with others programs and modes and have same results
https://en-forum.supla.org/viewtopic.php?p=66208#p66208
and this...
https://en-forum.supla.org/viewtopic.php?p=66412#p66412
and have same problems. I try flashing with others programs and modes and have same results
Więc chodź OSUPLUJE Ci dom
Druk 3D - > https://klimastech.eu.org/druk-3d
Druk 3D - > https://klimastech.eu.org/druk-3d