Przyciski, guziki, kontrolery scen - zgłoszenia, uwagi, pomysły [bramka ZigBee]

Lector · Post Wed Aug 06, 2025 7:20 pm

vajera wrote: Wed Aug 06, 2025 5:18 pm
Lector wrote: Wed Aug 06, 2025 12:37 pm
vajera wrote: Wed Aug 06, 2025 9:41 am

Dobra, chyba znalazłem rozwiązanie - wypróbuj 0.8.78-06/08/2025.
W Last binding result
Code: Select all
Unknown model LUMI::lumi.sensor_86sw1, no binding is possible
Bingo!

Ale nie dodaje

jakby co.

Zibi_007 · Post Wed Aug 06, 2025 7:28 pm

Lector wrote: Wed Aug 06, 2025 7:20 pm
vajera wrote: Wed Aug 06, 2025 5:18 pm
Lector wrote: Wed Aug 06, 2025 12:37 pm
W Last binding result
Code: Select all
Unknown model LUMI::lumi.sensor_86sw1, no binding is possible
Bingo!
Ale nie dodaje jakby co.

Doda, jak @vajera wrzuci do bazy +BWNU

vajera · Post Wed Aug 06, 2025 7:31 pm

Lector wrote: Wed Aug 06, 2025 7:20 pm
vajera wrote: Wed Aug 06, 2025 5:18 pm
Lector wrote: Wed Aug 06, 2025 12:37 pm
W Last binding result
Code: Select all
Unknown model LUMI::lumi.sensor_86sw1, no binding is possible
Bingo!
Ale nie dodaje jakby co.

Żeby bramka dodała urządzenie musi wiedzieć, jak się z nim komunikować. Do tego potrzebna jest przede wszystkim prawidłowa identyfikacja urządzenia - ten etap mamy już zaliczony. Teraz musisz dać mi chwilę czasu, bo ten przycisk wymaga nowego kodu.

vajera · Post Wed Aug 06, 2025 8:37 pm

Lector wrote: Wed Aug 06, 2025 7:20 pm Ale nie dodaje jakby co.

+BWNU 0.8.79-06/08/2025 - mniej więcej za 20 minut.

Jeżeli będzie działać to poproszę o info, jeżeli nie to o logi. Chociaż po namyśle logi tak czy inaczej mógłbyś podesłać

Lector · Post Thu Aug 07, 2025 8:33 am

vajera wrote: Wed Aug 06, 2025 8:37 pm
Lector wrote: Wed Aug 06, 2025 7:20 pm Ale nie dodaje jakby co.
+BWNU 0.8.79-06/08/2025 - mniej więcej za 20 minut.

Jeżeli będzie działać to poproszę o info, jeżeli nie to o logi. Chociaż po namyśle logi tak czy inaczej mógłbyś podesłać

Kanał SiNGLE się dodał.

Code: Select all

[10:30:03]Send: [53 55 50 4C 41 ]
[10:30:03][  2599][I][Z2S_Gateway.ino:1447] loop(): Starting Zigbee subsystem
[10:30:03][  2600][D][ZigbeeCore.cpp:167] zigbeeInit(): Initialize Zigbee stack
[10:30:03][  2603][D][ZigbeeCore.cpp:174] zigbeeInit(): Register all Zigbee EPs in list
[10:30:03][  2609][I][ZigbeeCore.cpp:182] zigbeeInit(): List of registered Zigbee EPs:
[10:30:03][  2610][I][ZigbeeCore.cpp:184] zigbeeInit(): Device type: Home Gateway, Endpoint: 1, Device ID: 0x0050
[10:30:03][  2616][V][ZigbeeCore.cpp:415] esp_zb_app_signal_handler(): ZDO signal: ZDO Config Ready (0x17), status: ESP_FAIL
[10:30:03][  2616][I][ZigbeeCore.cpp:276] esp_zb_app_signal_handler(): Zigbee stack initialized
[10:30:03][  2621][I][ZigbeeCore.cpp:391] esp_zb_app_signal_handler(): Network(0x7196) closed, devices joining not allowed.
[10:30:03][  2623][I][ZigbeeCore.cpp:282] esp_zb_app_signal_handler(): Device started up in non factory-reset mode
[10:30:03][  2623][I][ZigbeeCore.cpp:295] esp_zb_app_signal_handler(): Device rebooted
[10:30:03][  2624][I][ZigbeeCore.cpp:299] esp_zb_app_signal_handler(): Opening network for joining for 180 seconds
[10:30:03][  2625][D][ZigbeeCore.cpp:542] searchBindings(): Requesting binding table for address 0x0000
[10:30:03][  2627][D][ZigbeeCore.cpp:482] bindingTableCb(): Binding table callback for address 0x0000 with status 0
[10:30:03][  2627][D][ZigbeeCore.cpp:485] bindingTableCb(): Binding table info: total 1, index 0, count 1
[10:30:03][  2627][D][ZigbeeCore.cpp:495] bindingTableCb(): Binding table record: src_endp 1, dst_endp 1, cluster_id 0x0006, dst_addr_mode 3
[10:30:03][  2628][I][z2s_devices_table.cpp:1753] Z2S_onBTCBoundDevice(): BTC bound device(0x1d65) on endpoint(0x1), cluster id(0x6)
[10:30:03][  2629][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xffffffff
[10:30:03][  2629][I][z2s_devices_table.cpp:144] Z2S_findChannelNumberNextSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xffffffff
[10:30:03][  2630][I][ZigbeeGateway.cpp:1046] addBoundDevice(): New Zigbee device unit registered - IEEE address 0:15:8d:0:1:83:1a:f2, short address 0x1d65, model id 0x5610, last seen (ms) 0
[10:30:03][  2631][D][ZigbeeCore.cpp:512] bindingTableCb(): Device bound to EP 1 -> device endpoint: 216, short addr: 0x4084, ieee addr: 40:81:9D:B8:40:81:9D:B8
[10:30:03][  2631][D][ZigbeeCore.cpp:533] bindingTableCb(): Filling bounded devices finished
[10:30:03]- Telnet: [  2632][V][NetworkServer.h:41] NetworkServer(): NetworkServer::NetworkServer(port=23, ...)
[10:30:03]Telnet running
[10:30:03][  2634][I][z2s_web_gui.cpp:452] fillGatewayGeneralnformation(): Device information <b><i>Supla firmware:</i></b> SDK 25.07-dev<br><br><b><i>Supla GUID:</i></b> 132F5B881BD62FC2D6CEC8785992793F<br><br><b><i>Z2S Gateway version:</i></b> 0.8.79-06/08/2025<br><br>
[10:30:03][  2637][I][z2s_web_gui.cpp:470] fillMemoryUptimeInformation(): Memory & uptime information <b><i>Flash chip real size:</b></i> 4194304 B <b>| <i>Free Sketch Space:</b></i> 2621440 B<br><b><i>Free Heap:</b></i> 146052 B <b>| <i>Minimal Free Heap:</b></i> 143012 B <b>| <i>HeapSize:</b></i> 359516 B <b>| <i>MaxAllocHeap:</b></i> 120820 B<br><br><b><i>Local time:</i></b> Thu Aug  7 10:30:02 2025
[10:30:03]<b><i>Supla uptime:</i></b> 2 s
[10:30:03]Recv: [53 55 50 4C 41 17 02 00 00 00 AD 02 00 00 1C 00 00 00 01 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 01 00 01 53 55 50 4C 41 ]
[10:30:03]Received new device config
[10:30:03]Processing AutomaticTimeSync config
[10:30:03]Sending device config result OK (1)
[10:30:03]Send: [53 55 50 4C 41 17 04 00 00 00 B7 02 00 00 0A 00 00 00 01 00 00 00 00 00 00 00 00 00 ]
[10:30:03]Send: [53 55 50 4C 41 ]
[10:30:03]Relay[110] updating timer value: remainingTime=0 state=0
[10:30:03]SRPC sending: remaining time 0, channel 110, state 0
[10:30:03]Send: [53 55 50 4C 41 17 05 00 00 00 69 00 00 00 E3 00 00 00 6E 32 DD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
[10:30:03]Send: [53 55 50 4C 41 ]
[10:30:03]Recv: [53 55 50 4C 41 17 03 00 00 00 AA 02 00 00 08 00 00 00 00 82 00 00 00 00 00 00 53 55 50 4C 41 ]
[10:30:03]Channel[0] Received SetChannelConfig: fnc 130, config type 0, config size 0
[10:30:03]Channel[0] handleChannelConfig, func 130, configtype 0, configsize 0
[10:30:03]Relay[0] applyChannelConfig, func 130, configtype 0, configsize 0
[10:30:03]ConfigTypesBitmap: Set config type 5 to 0
[10:30:03]Channel[0] ConfigType 0 SetChannelConfigNeeded
[10:30:03]ConfigTypesBitmap: Set config type 0 to 0
[10:30:03]Channel[0] Sending SetChannelConfigResult OK (1)
[10:30:03]Send: [53 55 50 4C 41 17 06 00 00 00 B4 02 00 00 03 00 00 00 01 00 00 ]
[10:30:03]Send: [53 55 50 4C 41 ]
[10:30:03]Relay[0] updating timer value: remainingTime=0 state=0
[10:30:03]SRPC sending: remaining time 0, channel 0, state 0
[10:30:03]Send: [53 55 50 4C 41 17 07 00 00 00 69 00 00 00 E3 00 00 00 00 32 DD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
[10:30:03]Send: [53 55 50 4C 41 ]
[10:30:03]Recv: [53 55 50 4C 41 17 04 00 00 00 AB 02 00 00 01 00 00 00 00 53 55 50 4C 41 ]
[10:30:03]Channel[0] Received ChannelConfigFinished
[10:30:03]Channel[0] some config is missing on server... (rcv: 0x1 != used: 0x2)
[10:30:03]Send: [53 55 50 4C 41 17 08 00 00 00 80 02 00 00 1F 00 00 00 6E 3D 76 69 17 00 00 00 49 41 53 20 5A 4F 4E 45 20 4E 4F 54 49 46 49 43 41 54 49 4F 4E 53 00 ]
[10:30:03]Send: [53 55 50 4C 41 ]
[10:30:03]Recv: [53 55 50 4C 41 17 05 00 00 00 AA 02 00 00 32 00 00 00 6E 82 00 00 00 00 2A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 53 55 50 4C 41 ]
[10:30:03]Channel[110] Received SetChannelConfig: fnc 130, config type 0, config size 42
[10:30:03]Channel[110] handleChannelConfig, func 130, configtype 0, configsize 42
[10:30:03]Relay[110] applyChannelConfig, func 130, configtype 0, configsize 42
[10:30:03]ConfigTypesBitmap: Set config type 5 to 0
[10:30:03]Relay[110] OvercurrentMaxAllowed: 0, OvercurrentThreshold: 0
[10:30:03]Channel[110] ConfigType 0 applied
[10:30:03]ConfigTypesBitmap: Set config type 0 to 1
[10:30:03]Channel[110] Sending SetChannelConfigResult OK (1)
[10:30:03]Send: [53 55 50 4C 41 17 09 00 00 00 B4 02 00 00 03 00 00 00 01 00 6E ]
[10:30:03]Send: [53 55 50 4C 41 ]
[10:30:03]Send: [53 55 50 4C 41 17 0A 00 00 00 80 02 00 00 0F 00 00 00 00 82 00 00 07 00 00 00 53 49 4E 47 4C 45 00 ]
[10:30:03]Send: [53 55 50 4C 41 ]
[10:30:03]Recv: [53 55 50 4C 41 17 06 00 00 00 AB 02 00 00 01 00 00 00 6E 53 55 50 4C 41 ]
[10:30:03]Channel[110] Received ChannelConfigFinished
[10:30:03]ConfigTypesBitmap: Set all to 0x2
[10:30:03]Relay[0] fill channel config for power switch functions (or ext for staircase)
[10:30:03]Send: [53 55 50 4C 41 17 0B 00 00 00 A9 02 00 00 32 00 00 00 00 82 00 00 00 00 2A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
[10:30:03]Send: [53 55 50 4C 41 ]
[10:30:03]Channel[0] SetChannelConfig send, func 130, type 0
[10:30:03]Recv: [53 55 50 4C 41 17 07 00 00 00 DC 00 00 00 03 00 00 00 1E 0A F0 53 55 50 4C 41 ]
[10:30:03]Activity timeout set to 30 s
[10:30:03]Recv: [53 55 50 4C 41 17 08 00 00 00 EA 01 00 00 1A 00 00 00 E9 07 08 07 05 0A 1E 03 0E 00 00 00 45 75 72 6F 70 65 2F 57 61 72 73 61 77 00 53 55 50 4C 41 ]
[10:30:03]Clock: current time: 2025-08-07 10:30:02
[10:30:03]Clock: time diff (system-new): -1 s
[10:30:03]Clock: new time: 2025-08-07 10:30:03
[10:30:03]Recv: [53 55 50 4C 41 17 09 00 00 00 8A 02 00 00 20 00 00 00 6E 3D 76 69 1A 17 00 00 00 49 41 53 20 5A 4F 4E 45 20 4E 4F 54 49 46 49 43 41 54 49 4F 4E 53 00 53 55 50 4C 41 ]
[10:30:03]Channel[110] Receieved setChannelCaptionResult
[10:30:03]Recv: [53 55 50 4C 41 17 0A 00 00 00 8A 02 00 00 10 00 00 00 00 82 00 00 03 07 00 00 00 53 49 4E 47 4C 45 00 53 55 50 4C 41 ]
[10:30:03]Channel[0] Receieved setChannelCaptionResult
[10:30:03]Recv: [53 55 50 4C 41 17 0B 00 00 00 B3 02 00 00 03 00 00 00 01 00 00 53 55 50 4C 41 ]
[10:30:03]Channel[0] Set channel config succeeded (1) for config type 0
[10:30:03]ConfigTypesBitmap: Set config type 0 to 1
[10:30:03]Recv: [53 55 50 4C 41 17 0C 00 00 00 AA 02 00 00 32 00 00 00 00 82 00 00 00 00 2A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 53 55 50 4C 41 ]
[10:30:03]Channel[0] Received SetChannelConfig: fnc 130, config type 0, config size 42
[10:30:03]Channel[0] handleChannelConfig, func 130, configtype 0, configsize 42
[10:30:03]Relay[0] applyChannelConfig, func 130, configtype 0, configsize 42
[10:30:03]ConfigTypesBitmap: Set config type 5 to 0
[10:30:03]Relay[0] OvercurrentMaxAllowed: 0, OvercurrentThreshold: 0
[10:30:03]Channel[0] ConfigType 0 applied
[10:30:03]ConfigTypesBitmap: Set config type 0 to 1
[10:30:03]Channel[0] Sending SetChannelConfigResult OK (1)
[10:30:03]Send: [53 55 50 4C 41 17 0C 00 00 00 B4 02 00 00 03 00 00 00 01 00 00 ]
[10:30:03]Send: [53 55 50 4C 41 ]
[10:30:03][  3095][I][ZigbeeCore.cpp:388] esp_zb_app_signal_handler(): Network(0x7196) is open for 180 seconds
[10:30:04][  3539][V][esp32-hal-rmt.c:306] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[10:30:04][  3539][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Asked to Loop: NO, LoopCancel: NO
[10:30:08]LittleFsConfig: writing to file "/supla-dev.cfg"
[10:30:08]LittleFsConfig: writing to file "/supla-dev.cfg.bak"
[10:30:10][ 10001][I][Z2S_Gateway.ino:1544] loop(): Device on endpoint(0x1), short address(0x1d65), model id(0x5610), cluster id(0x6), rejoined(NO)
[10:30:10][ 10001][I][Z2S_Gateway.ino:1546] loop(): Gateway version: 0.8.79-06/08/2025
[10:30:10][ 10002][I][Z2S_Gateway.ino:1576] loop(): getZbgDeviceUnitLastSeenMs 0, current millis 10002
[10:30:10][ 10002][I][Z2S_Gateway.ino:1577] loop(): Memory information: Flash chip real size:4194304 B, Free Sketch Space:2621440 B, Free Heap:103800, Minimal Free Heap:73392 B, HeapSize:359516 B, MaxAllocHeap:83956 B, Supla uptime:10 s
[10:30:11]PowerCycle: timeout, counter reset to 0
[10:30:12]LittleFsConfig: writing to file "/supla-dev.cfg"
[10:30:12]LittleFsConfig: writing to file "/supla-dev.cfg.bak"

Ale nie zmienia stanu.

Code: Select all

[10:30:28]Send: [53 55 50 4C 41 17 0D 00 00 00 28 00 00 00 10 00 00 00 44 80 94 68 00 00 00 00 89 EF 03 00 00 00 00 00 ]
[10:30:28]Send: [53 55 50 4C 41 ]
[10:30:28]Recv: [53 55 50 4C 41 17 0D 00 00 00 32 00 00 00 10 00 00 00 24 64 94 68 00 00 00 00 32 57 0B 00 00 00 00 00 53 55 50 4C 41 ]
[10:30:50][ 49942][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[10:30:50][ 49943][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[10:30:50][ 49944][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report ON
[10:30:50][ 49944][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x1
[10:30:50][ 49945][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[10:30:50][ 49945][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[10:30:50][ 49946][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[10:30:50][ 49946][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[10:30:50][ 49947][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[10:30:50][ 49947][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[10:30:50][ 49948][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[10:30:50][ 49948][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[10:30:50][ 49949][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[10:30:50][ 49950][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report OFF
[10:30:50][ 49950][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x0
[10:30:50][ 49950][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[10:30:50][ 49951][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[10:30:50][ 49952][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[10:30:50][ 49952][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[10:30:50][ 49953][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[10:30:50][ 49954][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[10:30:50][ 49954][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[10:30:53]Send: [53 55 50 4C 41 17 0E 00 00 00 28 00 00 00 10 00 00 00 5D 80 94 68 00 00 00 00 45 FF 03 00 00 00 00 00 ]
[10:30:53]Send: [53 55 50 4C 41 ]
[10:30:53]Recv: [53 55 50 4C 41 17 0E 00 00 00 32 00 00 00 10 00 00 00 3D 64 94 68 00 00 00 00 DA 09 0B 00 00 00 00 00 53 55 50 4C 41 ]
[10:31:00][ 60001][I][Z2S_Gateway.ino:1477] loop(): New UTC time 807877860, new local time 807877860
[10:31:00][ 60002][I][Z2S_Gateway.ino:1491] loop(): Local Time Cluster UTC time attribute 807877860, local time attribute 807877860
[10:31:00][ 60003][I][z2s_web_gui.cpp:470] fillMemoryUptimeInformation(): Memory & uptime information <b><i>Flash chip real size:</b></i> 4194304 B <b>| <i>Free Sketch Space:</b></i> 2621440 B<br><b><i>Free Heap:</b></i> 103976 B <b>| <i>Minimal Free Heap:</b></i> 73392 B <b>| <i>HeapSize:</b></i> 359516 B <b>| <i>MaxAllocHeap:</b></i> 83956 B<br><br><b><i>Local time:</i></b> Thu Aug  7 10:31:00 2025
[10:31:00]<b><i>Supla uptime:</i></b> 60 s
[10:31:08][ 67785][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[10:31:08][ 67786][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[10:31:08][ 67786][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report ON
[10:31:08][ 67787][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x1
[10:31:08][ 67787][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[10:31:08][ 67788][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[10:31:08][ 67788][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[10:31:08][ 67789][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[10:31:08][ 67790][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[10:31:08][ 67790][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[10:31:08][ 67791][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[10:31:08][ 67791][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[10:31:08][ 67792][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[10:31:08][ 67793][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report OFF
[10:31:08][ 67793][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x0
[10:31:08][ 67793][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[10:31:08][ 67794][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[10:31:08][ 67795][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[10:31:08][ 67795][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[10:31:08][ 67796][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[10:31:08][ 67796][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[10:31:08][ 67797][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[10:31:15][ 74311][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[10:31:15][ 74311][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[10:31:15][ 74312][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report ON
[10:31:15][ 74312][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x1
[10:31:15][ 74313][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[10:31:15][ 74313][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[10:31:15][ 74314][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[10:31:15][ 74315][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[10:31:15][ 74315][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[10:31:15][ 74316][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[10:31:15][ 74316][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[10:31:15][ 74317][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[10:31:15][ 74317][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[10:31:15][ 74318][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report OFF
[10:31:15][ 74319][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x0
[10:31:15][ 74319][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[10:31:15][ 74320][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[10:31:15][ 74320][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[10:31:15][ 74321][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[10:31:15][ 74321][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[10:31:15][ 74322][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[10:31:15][ 74322][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[10:31:18][ 77486][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[10:31:18][ 77486][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[10:31:18][ 77487][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report ON
[10:31:18][ 77488][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x1
[10:31:18][ 77488][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[10:31:18][ 77489][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[10:31:18][ 77489][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[10:31:18][ 77490][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[10:31:18][ 77490][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[10:31:18][ 77491][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[10:31:18][ 77492][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[10:31:18][ 77492][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[10:31:18][ 77493][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[10:31:18][ 77493][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report OFF
[10:31:18][ 77494][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x0
[10:31:18][ 77494][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[10:31:18][ 77495][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[10:31:18][ 77495][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[10:31:18][ 77496][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[10:31:18][ 77496][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[10:31:18][ 77497][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[10:31:18][ 77498][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[10:31:18]Send: [53 55 50 4C 41 17 0F 00 00 00 28 00 00 00 10 00 00 00 76 80 94 68 00 00 00 00 A7 12 04 00 00 00 00 00 ]
[10:31:18]Send: [53 55 50 4C 41 ]
[10:31:18]Recv: [53 55 50 4C 41 17 0F 00 00 00 32 00 00 00 10 00 00 00 56 64 94 68 00 00 00 00 6C FA 0A 00 00 00 00 00 53 55 50 4C 41 ]
[10:31:43]Send: [53 55 50 4C 41 17 10 00 00 00 28 00 00 00 10 00 00 00 8F 80 94 68 00 00 00 00 D2 27 04 00 00 00 00 00 ]
[10:31:43]Send: [53 55 50 4C 41 ]
[10:31:43]Recv: [53 55 50 4C 41 17 10 00 00 00 32 00 00 00 10 00 00 00 6F 64 94 68 00 00 00 00 76 BA 0B 00 00 00 00 00 53 55 50 4C 41 ]
[10:31:57][116568][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[10:31:57][116568][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[10:31:57][116569][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report ON
[10:31:57][116569][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x1
[10:31:57][116570][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[10:31:57][116570][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[10:31:57][116571][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[10:31:57][116571][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[10:31:57][116572][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[10:31:57][116572][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[10:31:57][116573][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[10:31:57][116573][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[10:31:57][116574][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[10:31:57][116575][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report OFF
[10:31:57][116575][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x0
[10:31:57][116575][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[10:31:57][116576][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[10:31:57][116577][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[10:31:57][116577][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[10:31:57][116578][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[10:31:57][116578][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[10:31:57][116579][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[10:32:00][120006][I][Z2S_Gateway.ino:1477] loop(): New UTC time 807877920, new local time 807877920
[10:32:00][120007][I][Z2S_Gateway.ino:1491] loop(): Local Time Cluster UTC time attribute 807877920, local time attribute 807877920
[10:32:00][120008][I][z2s_web_gui.cpp:470] fillMemoryUptimeInformation(): Memory & uptime information <b><i>Flash chip real size:</b></i> 4194304 B <b>| <i>Free Sketch Space:</b></i> 2621440 B<br><b><i>Free Heap:</b></i> 104112 B <b>| <i>Minimal Free Heap:</b></i> 73392 B <b>| <i>HeapSize:</b></i> 359516 B <b>| <i>MaxAllocHeap:</b></i> 83956 B<br><br><b><i>Local time:</i></b> Thu Aug  7 10:32:00 2025
[10:32:00]<b><i>Supla uptime:</i></b> 120 s

W cloud nie ma zakładki "Wyzwalacze akcji".

Czy wnowczych wersjach już też będzie, bo testowałe tą co podałeś.

vajera · Post Thu Aug 07, 2025 9:03 am

Lector wrote: Thu Aug 07, 2025 8:33 am Kanał SiNGLE się dodał.
Ale nie zmienia stanu.

Mógłbyś wrzucić logi z naciskania przycisku, tzn. z taką informacją, w której sekundzie naciskasz przycisk i jakie logi bezpośrednio po tym lecą?

W cloud nie ma zakładki "Wyzwalacze akcji".

Czy wnowczych wersjach już też będzie, bo testowałe tą co podałeś.

Nie do końca rozumiem, o czym piszesz?

Lector · Post Thu Aug 07, 2025 9:35 am

vajera wrote: Thu Aug 07, 2025 9:03 am
Lector wrote: Thu Aug 07, 2025 8:33 am Kanał SiNGLE się dodał.
Ale nie zmienia stanu.

Mógłbyś wrzucić logi z naciskania przycisku, tzn. z taką informacją, w której sekundzie naciskasz przycisk i jakie logi bezpośrednio po tym lecą?
W cloud nie ma zakładki "Wyzwalacze akcji".

Czy wnowczych wersjach już też będzie, bo testowałe tą co podałeś.
Nie do końca rozumiem, o czym piszesz?

Tu log jak wduszam klawisz:

Code: Select all

[11:34:17][ 74851][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[11:34:17][ 74851][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[11:34:17][ 74852][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report ON
[11:34:17][ 74852][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x1
[11:34:17][ 74853][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[11:34:17][ 74854][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[11:34:17][ 74854][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[11:34:17][ 74855][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[11:34:17][ 74855][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[11:34:17][ 74856][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[11:34:17][ 74856][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[11:34:17][ 74857][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[11:34:17][ 74857][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[11:34:17][ 74858][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report OFF
[11:34:17][ 74858][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x0
[11:34:17][ 74859][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[11:34:17][ 74859][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[11:34:17][ 74860][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[11:34:17][ 74861][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[11:34:17][ 74861][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[11:34:17][ 74862][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[11:34:17][ 74862][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[11:34:20]Send: [53 55 50 4C 41 17 0C 00 00 00 28 00 00 00 10 00 00 00 3A 8F 94 68 00 00 00 00 86 A3 0E 00 00 00 00 00 ]
[11:34:20]Send: [53 55 50 4C 41 ]
[11:34:20]Recv: [53 55 50 4C 41 17 0C 00 00 00 32 00 00 00 10 00 00 00 1C 73 94 68 00 00 00 00 89 9C 01 00 00 00 00 00 53 55 50 4C 41 ]

Chodziło mi czy w kolejnej wersji też jest, bo pojawiła się już nowsza niż 0.8.79-06/08/2025.

vajera · Post Thu Aug 07, 2025 9:55 am

Lector wrote: Thu Aug 07, 2025 9:35 am

vajera wrote: Thu Aug 07, 2025 9:03 am
Lector wrote: Thu Aug 07, 2025 8:33 am Kanał SiNGLE się dodał.
Ale nie zmienia stanu.

Mógłbyś wrzucić logi z naciskania przycisku, tzn. z taką informacją, w której sekundzie naciskasz przycisk i jakie logi bezpośrednio po tym lecą?
W cloud nie ma zakładki "Wyzwalacze akcji".

Czy wnowczych wersjach już też będzie, bo testowałe tą co podałeś.
Nie do końca rozumiem, o czym piszesz?

Tu log jak wduszam klawisz:

Code: Select all

[11:34:17][ 74851][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[11:34:17][ 74851][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[11:34:17][ 74852][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report ON
[11:34:17][ 74852][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x1
[11:34:17][ 74853][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[11:34:17][ 74854][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[11:34:17][ 74854][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[11:34:17][ 74855][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[11:34:17][ 74855][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[11:34:17][ 74856][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[11:34:17][ 74856][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[11:34:17][ 74857][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[11:34:17][ 74857][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[11:34:17][ 74858][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report OFF
[11:34:17][ 74858][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x0
[11:34:17][ 74859][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[11:34:17][ 74859][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[11:34:17][ 74860][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[11:34:17][ 74861][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[11:34:17][ 74861][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[11:34:17][ 74862][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[11:34:17][ 74862][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[11:34:20]Send: [53 55 50 4C 41 17 0C 00 00 00 28 00 00 00 10 00 00 00 3A 8F 94 68 00 00 00 00 86 A3 0E 00 00 00 00 00 ]
[11:34:20]Send: [53 55 50 4C 41 ]
[11:34:20]Recv: [53 55 50 4C 41 17 0C 00 00 00 32 00 00 00 10 00 00 00 1C 73 94 68 00 00 00 00 89 9C 01 00 00 00 00 00 53 55 50 4C 41 ]

Chodziło mi czy w kolejnej wersji też jest, bo pojawiła się już nowsza niż 0.8.79-06/08/2025.

To jest log z pojedynczego kliknięcia, tak? On w teorii ma tylko jedną akcję, ale zobacz jeszcze logi z dwukliku i dłuższego przytrzymania przycisku?

Lector · Post Thu Aug 07, 2025 10:09 am

vajera wrote: Thu Aug 07, 2025 9:55 am To jest log z pojedynczego kliknięcia, tak? On w teorii ma tylko jedną akcję, ale zobacz jeszcze logi z dwukliku i dłuższego przytrzymania przycisku?

Tu długie przytrzymanie:

Code: Select all

[12:01:07][1684869][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[12:01:07][1684869][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[12:01:07][1684870][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report ON
[12:01:07][1684870][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x1
[12:01:07][1684871][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[12:01:07][1684872][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[12:01:07][1684872][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[12:01:07][1684873][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[12:01:07][1684874][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[12:01:07][1684874][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[12:01:07][1684875][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[12:01:07][1684875][I][ZigbeeHandlers.cpp:37] zb_action_handler(): Receive Zigbee action(0x2000) callback
[12:01:07][1684876][V][ZigbeeHandlers.cpp:133] zb_attribute_reporting_handler(): Received report from address(0x1d65) src endpoint(1) to dst endpoint(1) cluster(0x6)
[12:01:07][1684876][I][ZigbeeGateway.cpp:723] zbAttributeReporting(): on/off report OFF
[12:01:07][1684877][I][z2s_devices_table.cpp:1131] Z2S_onOnOffReceive(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, state 0x0
[12:01:07][1684877][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xb54
[12:01:07][1684878][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x3e8
[12:01:07][1684878][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfa0
[12:01:07][1684879][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfaa
[12:01:07][1684880][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0x1b58
[12:01:07][1684880][I][z2s_devices_table.cpp:121] Z2S_findChannelNumberSlot(): 0:15:8d:0:1:83:1a:f2, endpoint 0x1, channel type 0xfb4
[12:01:07][1684881][E][z2s_devices_table.cpp:43] no_channel_found_error_func(): No channel found for address 0:15:8d:0:1:83:1a:f2
[12:01:14][1691647][I][ZigbeeCore.cpp:406] esp_zb_app_signal_handler(): Joined device is leaving network (short: 0x1d65), rejoin (NO)

Klawisz mi się rozparował, po ponownym sparowaniu nie widzę logów.

Z tego co pamiętam jak to działało pod Xiaomi to był jeden klik, klawisz podwójny miał lewy klik, prawy klik i klik oba klawisze.

vajera · Post Thu Aug 07, 2025 3:09 pm

Lector wrote: Thu Aug 07, 2025 9:35 am ...

Wypróbuj 08.83-07/08/2025 - wystarczy upgrade/OTA.