[Problem - rozwiązany] CURRYSMARTER Zigbee Rolladenschalter 6.1 [bramka ZigBee]

Moderator: vajera

LukiSpajder
Posts: 1548
Joined: Tue Aug 18, 2020 2:22 pm
Has thanked: 25 times
Been thanked: 34 times

Post

vajera wrote: Sat Jan 24, 2026 6:00 pm
LukiSpajder wrote: Sat Jan 24, 2026 1:52 pm Proszę o dodanie sterownika rolet firmy CURRYSMARTER Zigbee Rolladenschalter 6.1
Strona producenta :
https://currysmarter.com/product/zigbee ... 8404204e3d

Instrukcja :

https://currysmarter.com/manual/z01supp ... 8404204e3d



Dane do dodania :

Unknown model _TZE284_waa352qv::TS0601, no binding is possible
+BWNU: 1.20.21-24/01/26 - proszę o feedback (w tym również o weryfikację DPs w TCC).
Dodało się bez problemu ale .......

- Odwrotnie działają przyciski w apce przyciski po prawej ,zamknij to otwórz ( przestawienie w cloud nic nie daje )
- przyciski po lewej w apce strzałka do góry otwiera i zaraz zamyka

Teraz dp_id :

cover position -- działa 0% zamkniecie w supla , 100% otwarcie w supla

cover calibration -- wystarczy tylko 0 oznacza włączenie kalibracji

motor reversal -- brak oznak dziania

backlight -- brak oznak działania w tyua jest trzy stany off, słabo, mocno

child lock -- działa :D

Pisze w instrukcji że można zmienić sygnalizację tych diod na panelu że otwarcie pokaże nie zapalone a zamknięta wszystkie świeca, teraz jest odwrotnie. W apce tuya nie mogę tego znaleźć tak jakby nie można zmienić.

Pytanie :

czy zamieszczać to w tym temacie ?
Top
User avatar
vajera
Posts: 7290
Joined: Wed Oct 31, 2018 7:58 am
Location: Biedrusko
Has thanked: 289 times
Been thanked: 161 times

Post

LukiSpajder wrote: Sat Jan 24, 2026 9:09 pm Dodało się bez problemu ale .......

- Odwrotnie działają przyciski w apce przyciski po prawej ,zamknij to otwórz ( przestawienie w cloud nic nie daje )
- przyciski po lewej w apce strzałka do góry otwiera i zaraz zamyka
Spróbuj "odwrotne sterowanie silnikiem" w Cloud?
Teraz dp_id :

cover position -- działa 0% zamkniecie w supla , 100% otwarcie w supla

cover calibration -- wystarczy tylko 0 oznacza włączenie kalibracji

Code: Select all

3,
                    "calibration",
                    tuya.valueConverterBasic.lookup({
                        START: tuya.enum(0),
                        END: tuya.enum(1),
Czyli wysyłasz 0, czekasz X sekund, wysyłasz 1 - tak kalibrujesz.
Bramka Zigbee <=> SUPLA
Więcej informacji tutaj:
https://forum.supla.org/viewforum.php?f=127
FAQ https://forum.supla.org/viewtopic.php?t=17277
Top
LukiSpajder
Posts: 1548
Joined: Tue Aug 18, 2020 2:22 pm
Has thanked: 25 times
Been thanked: 34 times

Post

vajera wrote: Sat Jan 24, 2026 9:17 pm
LukiSpajder wrote: Sat Jan 24, 2026 9:09 pm Dodało się bez problemu ale .......

- Odwrotnie działają przyciski w apce przyciski po prawej ,zamknij to otwórz ( przestawienie w cloud nic nie daje )
- przyciski po lewej w apce strzałka do góry otwiera i zaraz zamyka
Spróbuj "odwrotne sterowanie silnikiem" w Cloud?
żadne z tych ustawień w cloud nie działa

Teraz dp_id :

cover position -- działa 0% zamkniecie w supla , 100% otwarcie w supla

cover calibration -- wystarczy tylko 0 oznacza włączenie kalibracji

Code: Select all

3,
                    "calibration",
                    tuya.valueConverterBasic.lookup({
                        START: tuya.enum(0),
                        END: tuya.enum(1),
Czyli wysyłasz 0, czekasz X sekund, wysyłasz 1 - tak kalibrujesz.


kalibracja odbywa się automatycznie tylko ją wywojujemy chyba ;) nie ma podpięte pod roletę, ale sprawdzę to czy tak jest ( aktualnie robię małe malowanie tam gdzie ma być docelowo zamontowana sterownik i wszystko mam odpięte od rolety , spodobała mi się ta wizualizacji zamknięcia na panelu ;) ) może tam jest detekcja prądu ?
Top
User avatar
vajera
Posts: 7290
Joined: Wed Oct 31, 2018 7:58 am
Location: Biedrusko
Has thanked: 289 times
Been thanked: 161 times

Post

LukiSpajder wrote: Sat Jan 24, 2026 9:30 pm
vajera wrote: Sat Jan 24, 2026 9:17 pm
LukiSpajder wrote: Sat Jan 24, 2026 9:09 pm Dodało się bez problemu ale .......

- Odwrotnie działają przyciski w apce przyciski po prawej ,zamknij to otwórz ( przestawienie w cloud nic nie daje )
- przyciski po lewej w apce strzałka do góry otwiera i zaraz zamyka
Spróbuj "odwrotne sterowanie silnikiem" w Cloud?
żadne z tych ustawień w cloud nie działa

Teraz dp_id :

cover position -- działa 0% zamkniecie w supla , 100% otwarcie w supla

cover calibration -- wystarczy tylko 0 oznacza włączenie kalibracji

Code: Select all

3,
                    "calibration",
                    tuya.valueConverterBasic.lookup({
                        START: tuya.enum(0),
                        END: tuya.enum(1),
Czyli wysyłasz 0, czekasz X sekund, wysyłasz 1 - tak kalibrujesz.


kalibracja odbywa się automatycznie tylko ją wywojujemy chyba ;) nie ma podpięte pod roletę, ale sprawdzę to czy tak jest ( aktualnie robię małe malowanie tam gdzie ma być docelowo zamontowana sterownik i wszystko mam odpięte od rolety , spodobała mi się ta wizualizacji zamknięcia na panelu ;) ) może tam jest detekcja prądu ?
To podłącz żarówkę 😉
Bramka Zigbee <=> SUPLA
Więcej informacji tutaj:
https://forum.supla.org/viewforum.php?f=127
FAQ https://forum.supla.org/viewtopic.php?t=17277
Top
LukiSpajder
Posts: 1548
Joined: Tue Aug 18, 2020 2:22 pm
Has thanked: 25 times
Been thanked: 34 times

Post

vajera wrote: Sat Jan 24, 2026 9:41 pm
LukiSpajder wrote: Sat Jan 24, 2026 9:30 pm
vajera wrote: Sat Jan 24, 2026 9:17 pm
Spróbuj "odwrotne sterowanie silnikiem" w Cloud?
żadne z tych ustawień w cloud nie działa

Teraz dp_id :

cover position -- działa 0% zamkniecie w supla , 100% otwarcie w supla

cover calibration -- wystarczy tylko 0 oznacza włączenie kalibracji

Code: Select all

3,
                    "calibration",
                    tuya.valueConverterBasic.lookup({
                        START: tuya.enum(0),
                        END: tuya.enum(1),
Czyli wysyłasz 0, czekasz X sekund, wysyłasz 1 - tak kalibrujesz.


kalibracja odbywa się automatycznie tylko ją wywojujemy chyba ;) nie ma podpięte pod roletę, ale sprawdzę to czy tak jest ( aktualnie robię małe malowanie tam gdzie ma być docelowo zamontowana sterownik i wszystko mam odpięte od rolety , spodobała mi się ta wizualizacji zamknięcia na panelu ;) ) może tam jest detekcja prądu ?
To podłącz żarówkę 😉
a więc tak jest detekcja jakaś ale działa to tak że jeżeli roleta nie pobiera prądu to wyłącznik zrobi off jeśli cały czas pobiera prąd to działa no stop mimo kalibracji , podepnę to jutro fizycznie pod roletę i zobaczę
Top
LukiSpajder
Posts: 1548
Joined: Tue Aug 18, 2020 2:22 pm
Has thanked: 25 times
Been thanked: 34 times

Post

Kolejne testy

i tak automatyczna kalibracja wysyłamy 0 i się kalibruje ma coś w sobie co monitoruje prąd , powtarza dwa razy procedurę i kalibruje.

Jeśli dojedzie do skrajne pozycji nie wyłączy przekaźnika dopóki krańcówka rolety nie rozłączy obwodu - trzyma go złącznym.
Przy wysłaniu pozycji np. 50 % ustawi roletę i wyłączy ( testy robione na żarówce )

Odnośnie backlight to tu logi jak to przetłumaczyć ;) :

Code: Select all

 [07:53:55][ 38192][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[07:53:55][ 38192][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[07:53:55][ 38193][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[07:53:55][ 38193][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[07:53:55][ 38194][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[07:53:55][ 38194][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0x22
[07:53:55][ 38195][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x66
[07:53:55][ 38195][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[07:53:55][ 38196][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[07:53:55][ 38196][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[07:53:55][ 38197][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x2
[07:53:55][ 38197][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[07:54:14]Send: [53 55 50 4C 41 1B 11 00 00 00 28 00 00 00 10 00 00 00 24 CC 75 69 00 00 00 00 56 52 00 00 00 00 00 00 ]
[07:54:14]Send: [53 55 50 4C 41 ]

Code: Select all

Using 'COM8' as serial port.
Unexpected error: could not open port 'COM8': PermissionError(13, 'Odmowa dostępu.', None, 5)
[08:16:52][442952][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:16:52][442953][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:16:52]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[08:16:52]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:16:52]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 0, rx_time: 0
[08:16:52][442954][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:16:52][442955][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:16:52][442955][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:16:52][442956][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:16:52][442956][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 10 size: 7
[08:16:52][442957][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:16:52][442957][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xDB 
[08:16:52][442957][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:16:52][442958][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:16:52][442958][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:16:52][442959][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:16:52][442959][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:16:52][442959][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:16:52][442960][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:16:52][442961][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:16:52][442961][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:16:52][442962][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:16:52][442963][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:16:52][442963][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:16:52][442964][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:16:52][442964][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:16:52][442965][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0xdb
[08:16:52][442965][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[08:16:52][442965][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:16:52][442966][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:16:52][442966][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:16:52][442968][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x1
[08:16:52][442968][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:16:52][442969][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 1
[08:16:53][443926][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:16:53][443927][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:16:53]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[08:16:53]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:16:53]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 10, rx_time: 0
[08:16:53][443928][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:16:53][443929][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:16:53][443929][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:16:53][443930][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:16:53][443930][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 11 size: 7
[08:16:53][443931][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:16:53][443931][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x1C 
[08:16:53][443931][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x66 
[08:16:53][443932][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:16:53][443932][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:16:53][443932][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:16:53][443933][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x02 
[08:16:53][443933][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:16:53][443934][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:16:53][443934][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:16:53][443935][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:16:53][443936][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:16:53][443936][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:16:53][443937][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:16:53][443937][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:16:53][443938][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:16:53][443938][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0x1c
[08:16:53][443938][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x66
[08:16:53][443939][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:16:53][443939][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:16:53][443940][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:16:53][443940][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x2
[08:16:53][443941][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:17:05]Send: [53 55 50 4C 41 1B 1E 00 00 00 28 00 00 00 10 00 00 00 7F D1 75 69 00 00 00 00 62 53 0D 00 00 00 00 00 ]
[08:17:05]Send: [53 55 50 4C 41 ]
[08:17:05]Recv: [53 55 50 4C 41 1B 1C 00 00 00 32 00 00 00 10 00 00 00 70 C3 75 69 00 00 00 00 70 B7 02 00 00 00 00 00 53 55 50 4C 41 ]
[08:17:14][464406][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:17:14][464407][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:17:14]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0x0000, asdu_length: 15
[08:17:14]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:17:14]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 20, rx_time: 0
[08:17:14][464408][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0x0, command id: 10
[08:17:14][464409][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:17:14][464409][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 1, disable_default_response 0, is_manuf_specific 0
[08:17:14][464410][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:17:14][464410][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 14 size: 12
[08:17:14][464411][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:17:14][464411][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:17:14][464411][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x20 
[08:17:14][464412][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x4E 
[08:17:14][464412][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xE2 
[08:17:14][464412][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xFF 
[08:17:14][464413][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x20 
[08:17:14][464413][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x38 
[08:17:14][464413][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xE4 
[08:17:14][464414][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xFF 
[08:17:14][464414][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x20 
[08:17:14][464414][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:17:14][464415][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:17:14][464415][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0x0, cmd id 0xa
[08:17:14][464416][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:17:14][464416][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:17:14][464417][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x2000) callback
[08:17:14][464418][V][ZigbeeHandlers.cpp:234] zb_attribute_reporting_handler(): Received report from address(0xbb17) src endpoint(1) to dst endpoint(1) cluster(0x0)
[08:17:14][464418][I][ZigbeeGateway.cpp:730] zbReadBasicCluster(): ZCL application version id is "78"
[08:17:14][464419][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x2000) callback
[08:17:14][464419][V][ZigbeeHandlers.cpp:234] zb_attribute_reporting_handler(): Received report from address(0xbb17) src endpoint(1) to dst endpoint(1) cluster(0x0)
[08:17:14][464420][I][ZigbeeGateway.cpp:752] zbReadBasicCluster(): attribute reporting with short address(0xBB17), updating IEEE address
[08:17:14][464421][I][ZigbeeGateway.cpp:756] zbReadBasicCluster(): Basic cluster: attribute(0xFFE2), type (0x20), size (0x01)
[08:17:14][464421][I][z2s_devices_table.cpp:3128] Z2S_onBasicReceive(): A4:C1:38:1C:73:1D:2A:09, short address 0xbb17 endpoint 0x1, attribute id 0xffe2, size 1
[08:17:14][464422][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x2000) callback
[08:17:14][464422][V][ZigbeeHandlers.cpp:234] zb_attribute_reporting_handler(): Received report from address(0xbb17) src endpoint(1) to dst endpoint(1) cluster(0x0)
[08:17:14][464423][I][ZigbeeGateway.cpp:752] zbReadBasicCluster(): attribute reporting with short address(0xBB17), updating IEEE address
[08:17:14][464424][I][ZigbeeGateway.cpp:756] zbReadBasicCluster(): Basic cluster: attribute(0xFFE4), type (0x20), size (0x01)
[08:17:14][464424][I][z2s_devices_table.cpp:3128] Z2S_onBasicReceive(): A4:C1:38:1C:73:1D:2A:09, short address 0xbb17 endpoint 0x1, attribute id 0xffe4, size 1

to odnośnie sterownia które działa teraz odwrotni teraz :

ip_dp 1 ENUM
0 - Stop
1 - zamknij
2 - otwórz

tu logi z ręcznej kalibracji

Code: Select all

Using 'COM8' as serial port.
Unexpected error: could not open port 'COM8': PermissionError(13, 'Odmowa dostępu.', None, 5)
[08:14:52][322710][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:14:52][322711][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:14:52]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[08:14:52]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:14:52]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 0, rx_time: 0
[08:14:52][322713][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:14:52][322713][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:14:52][322714][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:14:52][322714][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:14:52][322715][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 50 size: 7
[08:14:52][322715][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:52][322715][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xCF 
[08:14:52][322716][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:52][322716][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:14:52][322716][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:52][322717][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:52][322717][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:52][322717][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:14:52][322718][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:14:52][322719][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:14:52][322719][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:14:52][322720][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:14:52][322720][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:14:52][322721][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:14:52][322721][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:14:52][322722][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:14:52][322722][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0xcf
[08:14:52][322723][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[08:14:52][322723][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:14:52][322723][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:14:52][322724][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:14:52][322724][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x1
[08:14:52][322725][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:14:52][322726][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 1
[08:14:52][322732][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:14:52][322732][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:14:52]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[08:14:52]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:14:52]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 0, rx_time: 0
[08:14:52][322734][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:14:52][322734][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:14:52][322735][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:14:52][322735][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:14:52][322736][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 51 size: 7
[08:14:52][322736][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:52][322736][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xD0 
[08:14:52][322737][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:52][322737][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:14:52][322737][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:52][322738][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:52][322738][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:52][322738][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:14:52][322739][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:14:52][322740][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:14:52][322740][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:14:52][322742][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:14:52][322742][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:14:52][322743][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:14:52][322743][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:14:52][322743][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:14:52][322744][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0xd0
[08:14:52][322744][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[08:14:52][322745][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:14:52][322745][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:14:52][322746][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:14:52][322746][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x1
[08:14:52][322746][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:14:52][322747][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 1
[08:14:52][322761][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:14:52][322761][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:14:52]APSDE INDICATION - src_addr_mode: 0, cluster_id: 0xef00, asdu_length: 10
[08:14:52]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:14:52]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 0, rx_time: 0
[08:14:52][322763][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:14:52][322764][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:14:52][322764][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:14:52][322765][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:14:52][322765][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 52 size: 7
[08:14:52][322766][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:52][322766][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xD1 
[08:14:52][322766][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:52][322766][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:14:52][322767][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:52][322767][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:52][322768][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:52][322768][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:14:52][322768][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:14:52][322769][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:14:52][322770][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:14:52][322770][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:14:52][322771][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:14:52][322771][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:14:53][322772][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:14:53][322772][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:14:53][322773][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0xd1
[08:14:53][322773][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[08:14:53][322774][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:14:53][322774][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:14:53][322775][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:14:53][322775][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x1
[08:14:53][322776][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:14:53][322776][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 1
[08:14:53][322779][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:14:53][322779][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:14:53]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[08:14:53]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:14:53]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 0, rx_time: 0
[08:14:53][322781][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:14:53][322781][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:14:53][322782][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:14:53][322782][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:14:53][322783][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 53 size: 7
[08:14:53][322783][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:53][322783][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xD2 
[08:14:53][322784][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322784][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:14:53][322785][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:53][322785][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322785][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322786][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:14:53][322786][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:14:53][322787][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:14:53][322788][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:14:53][322788][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:14:53][322789][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:14:53][322789][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:14:53][322790][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:14:53][322790][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:14:53][322791][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0xd2
[08:14:53][322791][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[08:14:53][322792][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:14:53][322792][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:14:53][322793][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:14:53][322793][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x1
[08:14:53][322794][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:14:53][322794][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 1
[08:14:53][322796][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:14:53][322797][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:14:53]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[08:14:53]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:14:53]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 0, rx_time: 0
[08:14:53][322799][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:14:53][322799][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:14:53][322800][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:14:53][322800][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:14:53][322801][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 54 size: 7
[08:14:53][322801][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:53][322801][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xD3 
[08:14:53][322802][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322802][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:14:53][322803][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:53][322803][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322803][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322804][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:14:53][322804][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:14:53][322805][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:14:53][322805][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:14:53][322806][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:14:53][322807][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:14:53][322807][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:14:53][322808][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:14:53][322808][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:14:53][322809][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0xd3
[08:14:53][322809][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[08:14:53][322810][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:14:53][322810][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:14:53][322810][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:14:53][322811][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x1
[08:14:53][322812][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:14:53][322812][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 1
[08:14:53][322814][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:14:53][322815][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:14:53]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[08:14:53]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:14:53]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 0, rx_time: 0
[08:14:53][322817][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:14:53][322817][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:14:53][322818][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:14:53][322818][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:14:53][322819][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 55 size: 7
[08:14:53][322819][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:53][322819][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xD4 
[08:14:53][322820][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322820][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:14:53][322820][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:53][322821][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322821][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322821][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:14:53][322822][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:14:53][322823][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:14:53][322823][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:14:53][322824][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:14:53][322824][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:14:53][322825][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:14:53][322825][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:14:53][322826][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:14:53][322826][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0xd4
[08:14:53][322827][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[08:14:53][322827][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:14:53][322828][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:14:53][322828][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:14:53][322829][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x1
[08:14:53][322829][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:14:53][322830][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 1
[08:14:53][322832][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:14:53][322833][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:14:53]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[08:14:53]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:14:53]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 30, rx_time: 0
[08:14:53][322835][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:14:53][322835][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:14:53][322836][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:14:53][322836][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:14:53][322837][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 56 size: 7
[08:14:53][322837][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:53][322837][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xD5 
[08:14:53][322838][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322838][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:14:53][322838][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:53][322839][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322839][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322839][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:14:53][322840][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:14:53][322841][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:14:53][322841][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:14:53][322842][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:14:53][322843][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:14:53][322844][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:14:53][322844][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:14:53][322844][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:14:53][322845][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0xd5
[08:14:53][322845][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[08:14:53][322846][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:14:53][322846][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:14:53][322847][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:14:53][322847][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x1
[08:14:53][322848][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:14:53][322848][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 1
[08:14:53][322864][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:14:53][322864][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:14:53]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[08:14:53]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:14:53]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 0, rx_time: 0
[08:14:53][322866][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:14:53][322867][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:14:53][322867][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:14:53][322868][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:14:53][322868][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 57 size: 7
[08:14:53][322869][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:53][322869][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xD6 
[08:14:53][322869][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322870][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:14:53][322870][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:53][322870][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322871][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322871][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:14:53][322871][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:14:53][322872][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:14:53][322873][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:14:53][322873][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:14:53][322874][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:14:53][322874][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:14:53][322875][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:14:53][322875][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:14:53][322876][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0xd6
[08:14:53][322876][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[08:14:53][322877][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:14:53][322877][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:14:53][322878][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:14:53][322878][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x1
[08:14:53][322879][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:14:53][322879][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 1
[08:14:53][322882][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:14:53][322882][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:14:53]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[08:14:53]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:14:53]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 30, rx_time: 0
[08:14:53][322884][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:14:53][322884][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:14:53][322885][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:14:53][322885][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:14:53][322886][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 58 size: 7
[08:14:53][322886][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:53][322887][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xD7 
[08:14:53][322887][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322887][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:14:53][322888][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:53][322888][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322888][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:53][322889][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:14:53][322889][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:14:53][322890][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:14:53][322890][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:14:53][322891][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:14:53][322892][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:14:53][322892][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:14:53][322893][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:14:53][322893][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:14:54][322894][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0xd7
[08:14:54][322894][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[08:14:54][322894][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:14:54][322895][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:14:54][322895][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:14:54][322896][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x1
[08:14:54][322896][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:14:54][322897][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 1
[08:14:54][322899][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:14:54][322900][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:14:54]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[08:14:54]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:14:54]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 30, rx_time: 0
[08:14:54][322901][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:14:54][322902][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:14:54][322902][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:14:54][322903][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:14:54][322903][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 59 size: 7
[08:14:54][322904][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:54][322904][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xD8 
[08:14:54][322904][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:54][322905][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:14:54][322905][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:54][322905][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:54][322906][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:54][322906][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:14:54][322907][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:14:54][322907][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:14:54][322908][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:14:54][322909][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:14:54][322909][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:14:54][322910][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:14:54][322910][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:14:54][322911][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:14:54][322911][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0xd8
[08:14:54][322912][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[08:14:54][322912][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:14:54][322913][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:14:54][322913][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:14:54][322913][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x1
[08:14:54][322914][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:14:54][322915][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 1
[08:14:54][322917][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:14:54][322917][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:14:54]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[08:14:54]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:14:54]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 30, rx_time: 0
[08:14:54][322919][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:14:54][322920][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:14:54][322920][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:14:54][322921][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:14:54][322921][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 60 size: 7
[08:14:54][322921][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:54][322922][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xD9 
[08:14:54][322922][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:54][322922][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:14:54][322923][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:54][322923][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:54][322924][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:54][322924][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:14:54][322924][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:14:54][322925][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:14:54][322926][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:14:54][322926][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:14:54][322927][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:14:54][322927][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:14:54][322928][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:14:54][322928][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:14:54][322929][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0xd9
[08:14:54][322929][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[08:14:54][322930][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:14:54][322930][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:14:54][322931][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:14:54][322931][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x1
[08:14:54][322932][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:14:54][322932][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 1
[08:14:54][322935][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[08:14:54][322935][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[08:14:54]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[08:14:54]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[08:14:54]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 30, rx_time: 0
[08:14:54][322937][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[08:14:54][322937][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[08:14:54][322938][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[08:14:54][322938][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[08:14:54][322939][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 61 size: 7
[08:14:54][322939][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:54][322939][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0xDA 
[08:14:54][322940][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:54][322940][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[08:14:54][322940][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[08:14:54][322941][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:54][322941][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[08:14:54][322942][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[08:14:54][322942][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[08:14:54][322943][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[08:14:54][322943][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[08:14:54][322944][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[08:14:54][322945][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[08:14:54][322945][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[08:14:54][322946][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[08:14:54][322946][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[08:14:54][322947][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0xda
[08:14:54][322947][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[08:14:54][322948][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[08:14:54][322948][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[08:14:54][322949][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[08:14:54][322949][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x1
[08:14:54][322950][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[08:14:54][322950][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 1
[08:15:00]Send: [53 55 50 4C 41 1B 19 00 00 00 28 00 00 00 10 00 00 00 02 D1 75 69 00 00 00 00 B8 0C 0D 00 00 00 00 00 ]
[08:15:00]Send: [53 55 50 4C 41 ]
[08:15:00]Recv: [53 55 50 4C 41 1B 17 00 00 00 32 00 00 00 10 00 00 00 F3 C2 75 69 00 00 00 00 A1 2E 02 00 00 00 00 00 53 55 50 4C 41 ]
[08:15:25]Send: [53 55 50 4C 41 1B 1A 00 00 00 28 00 00 00 10 00 00 00 1B D1 75 69 00 00 00 00 A9 18 0D 00 00 00 00 00 ]
[08:15:25]Send: [53 55 50 4C 41 ]
[08:15:25]Recv: [53 55 50 4C 41 1B 18 00 00 00 32 00 00 00 10 00 00 00 0C C3 75 69 00 00 00 00 F0 26 02 00 00 00 00 00 53 55 50 4C 41 ]
[08:15:29][360058][I][Z2S_Gateway.ino:944] loop(): New UTC time 822644128, new local time 822644128
[08:15:29][360059][I][Z2S_Gateway.ino:976] loop(): 
[08:15:29]Local Time Cluster Time status attribute 2
[08:15:29]UTC time attribute 822644128
[08:15:29]local time attribute 822644128
[08:15:29][360061][I][z2s_web_gui.cpp:843] fillMemoryUptimeInformation(): Memory & uptime information <b><i>Flash chip real size:</b></i> 8388608 B <b>| <i>Free Sketch Space:</b></i> 3407872 B<br><b><i>HeapSize:</b></i> 358028 B <b>| <i>FreeHeap:</b></i> 53784 B <b>| <i>MinimalFreeHeap:</b></i> 35568 B <b>| <i>MaxAllocHeap:</b></i> 33780 B<br><b><i>uxTaskGetStackHighWaterMark:</b></i> 2976 B <br><b><i>Total PSRAM:</b></i> 0 B <b>| <i>Free PSRAM:</b></i> 0 B<br><br><b><i>Local time:</i></b> Sun Jan 25 08:15:28 2026
[08:15:29]<b><i>Supla uptime:</i></b> 360 s

logi z automatycznej kalibracji :
logi kalibracja auto.rar
You do not have the required permissions to view the files attached to this post.
Top
User avatar
vajera
Posts: 7290
Joined: Wed Oct 31, 2018 7:58 am
Location: Biedrusko
Has thanked: 289 times
Been thanked: 161 times

Post

LukiSpajder wrote: Sun Jan 25, 2026 7:17 am Odnośnie backlight to tu logi jak to przetłumaczyć ;) :

Code: Select all

...

Code: Select all

...
Wychodzi na, że backlight jest pod DP 102 (0x66), jest typu ENUM8 i przyjmuje wartości 0-2 (1-3?).

Zrób proszę zrzut ekranu z aplikacji Supla (widok rolety) i zaznacz, które przyciski działają prawidłowo a które odwrotnie lub wcale.
Bramka Zigbee <=> SUPLA
Więcej informacji tutaj:
https://forum.supla.org/viewforum.php?f=127
FAQ https://forum.supla.org/viewtopic.php?t=17277
Top
LukiSpajder
Posts: 1548
Joined: Tue Aug 18, 2020 2:22 pm
Has thanked: 25 times
Been thanked: 34 times

Post

vajera wrote: Sun Jan 25, 2026 7:49 am
LukiSpajder wrote: Sun Jan 25, 2026 7:17 am Odnośnie backlight to tu logi jak to przetłumaczyć ;) :

Code: Select all

...

Code: Select all

...
Wychodzi na, że backlight jest pod DP 102 (0x66), jest typu ENUM8 i przyjmuje wartości 0-2 (1-3?).

Zrób proszę zrzut ekranu z aplikacji Supla (widok rolety) i zaznacz, które przyciski działają prawidłowo a które odwrotnie lub wcale.
Ip_dp 102 ENUM - dział i tak
0- mocno
1- słabo
2- off

A to odnośnie sterowania w apce :
You do not have the required permissions to view the files attached to this post.
Top
LukiSpajder
Posts: 1548
Joined: Tue Aug 18, 2020 2:22 pm
Has thanked: 25 times
Been thanked: 34 times

Post

Sterownik po osiągnieciu pozycji pełnego otwarcia/zamknięcia nie wyłączy przekaźnika jeśli dalej odbiornik pobiera prąd czyli nie zadziała krańcówka w rolecie. Po około 5 minutach wyłączy przekaźnik tu logi z takiego wyłączenia. Może coś tam zobaczysz czy można zmienić ten czas ?

Code: Select all

[09:58:12][383234][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[09:58:12][383235][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[09:58:12][383235][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 10
[09:58:12][383235][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[09:58:12][383236][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0x1f
[09:58:12][383236][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x2
[09:58:12][383237][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x2
[09:58:12][383237][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[09:58:12][383238][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x4
[09:58:12][383238][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x0
[09:58:12][383239][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x7] = 0x0
[09:58:12][383239][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x8] = 0x0
[09:58:12][383239][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x9] = 0x0
[09:58:12][383240][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[09:58:12][383241][I][z2s_device_tuya_custom_cluster.cpp:2158] processMoesShadesDriveMotorDataReport(): position = 0



tutaj większy fragment tylko przy zamykaniu, pod koniec logów wyłączyło :

Code: Select all

[10:02:34][645687][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[10:02:34][645688][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x2000) callback
[10:02:34][645688][V][ZigbeeHandlers.cpp:234] zb_attribute_reporting_handler(): Received report from address(0xbb17) src endpoint(1) to dst endpoint(1) cluster(0x0)
[10:02:34][645689][I][ZigbeeGateway.cpp:730] zbReadBasicCluster(): ZCL application version id is "78"
[10:02:34][645690][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x2000) callback
[10:02:34][645690][V][ZigbeeHandlers.cpp:234] zb_attribute_reporting_handler(): Received report from address(0xbb17) src endpoint(1) to dst endpoint(1) cluster(0x0)
[10:02:34][645691][I][ZigbeeGateway.cpp:752] zbReadBasicCluster(): attribute reporting with short address(0xBB17), updating IEEE address
[10:02:34][645691][I][ZigbeeGateway.cpp:756] zbReadBasicCluster(): Basic cluster: attribute(0xFFE2), type (0x20), size (0x01)
[10:02:34][645692][I][z2s_devices_table.cpp:3128] Z2S_onBasicReceive(): A4:C1:38:1C:73:1D:2A:09, short address 0xbb17 endpoint 0x1, attribute id 0xffe2, size 1
[10:02:34][645693][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x2000) callback
[10:02:34][645693][V][ZigbeeHandlers.cpp:234] zb_attribute_reporting_handler(): Received report from address(0xbb17) src endpoint(1) to dst endpoint(1) cluster(0x0)
[10:02:34][645694][I][ZigbeeGateway.cpp:752] zbReadBasicCluster(): attribute reporting with short address(0xBB17), updating IEEE address
[10:02:34][645694][I][ZigbeeGateway.cpp:756] zbReadBasicCluster(): Basic cluster: attribute(0xFFE4), type (0x20), size (0x01)
[10:02:34][645695][I][z2s_devices_table.cpp:3128] Z2S_onBasicReceive(): A4:C1:38:1C:73:1D:2A:09, short address 0xbb17 endpoint 0x1, attribute id 0xffe4, size 1
[10:02:44]Send: [53 55 50 4C 41 1B 46 00 00 00 28 00 00 00 10 00 00 00 41 EA 75 69 00 00 00 00 D7 EA 0D 00 00 00 00 00 ]
[10:02:44]Send: [53 55 50 4C 41 ]
[10:02:44]Recv: [53 55 50 4C 41 1B 25 00 00 00 32 00 00 00 10 00 00 00 32 DC 75 69 00 00 00 00 B3 0B 0C 00 00 00 00 00 53 55 50 4C 41 ]
[10:02:48][660077][I][Z2S_Gateway.ino:944] loop(): New UTC time 822650566, new local time 822650566
[10:02:48][660078][I][Z2S_Gateway.ino:976] loop(): 
[10:02:48]Local Time Cluster Time status attribute 2
[10:02:48]UTC time attribute 822650566
[10:02:48]local time attribute 822650566
[10:02:48][660080][I][z2s_web_gui.cpp:843] fillMemoryUptimeInformation(): Memory & uptime information <b><i>Flash chip real size:</b></i> 8388608 B <b>| <i>Free Sketch Space:</b></i> 3407872 B<br><b><i>HeapSize:</b></i> 358028 B <b>| <i>FreeHeap:</b></i> 56080 B <b>| <i>MinimalFreeHeap:</b></i> 43484 B <b>| <i>MaxAllocHeap:</b></i> 40948 B<br><b><i>uxTaskGetStackHighWaterMark:</b></i> 2912 B <br><b><i>Total PSRAM:</b></i> 0 B <b>| <i>Free PSRAM:</b></i> 0 B<br><br><b><i>Local time:</i></b> Sun Jan 25 10:02:46 2026
[10:02:48]<b><i>Supla uptime:</i></b> 660 s
[10:03:09]Send: [53 55 50 4C 41 1B 47 00 00 00 28 00 00 00 10 00 00 00 5A EA 75 69 00 00 00 00 56 F6 0D 00 00 00 00 00 ]
[10:03:09]Send: [53 55 50 4C 41 ]
[10:03:09]Recv: [53 55 50 4C 41 1B 26 00 00 00 32 00 00 00 10 00 00 00 4B DC 75 69 00 00 00 00 FD E7 0B 00 00 00 00 00 53 55 50 4C 41 ]
[10:03:34]Send: [53 55 50 4C 41 1B 48 00 00 00 28 00 00 00 10 00 00 00 73 EA 75 69 00 00 00 00 CC 01 0E 00 00 00 00 00 ]
[10:03:34]Send: [53 55 50 4C 41 ]
[10:03:34]Recv: [53 55 50 4C 41 1B 27 00 00 00 32 00 00 00 10 00 00 00 64 DC 75 69 00 00 00 00 7E A9 0B 00 00 00 00 00 53 55 50 4C 41 ]
[10:03:48][720084][I][Z2S_Gateway.ino:944] loop(): New UTC time 822650626, new local time 822650626
[10:03:48][720085][I][Z2S_Gateway.ino:976] loop(): 
[10:03:48]Local Time Cluster Time status attribute 2
[10:03:48]UTC time attribute 822650626
[10:03:48]local time attribute 822650626
[10:03:48][720087][I][z2s_web_gui.cpp:843] fillMemoryUptimeInformation(): Memory & uptime information <b><i>Flash chip real size:</b></i> 8388608 B <b>| <i>Free Sketch Space:</b></i> 3407872 B<br><b><i>HeapSize:</b></i> 358028 B <b>| <i>FreeHeap:</b></i> 56080 B <b>| <i>MinimalFreeHeap:</b></i> 43484 B <b>| <i>MaxAllocHeap:</b></i> 40948 B<br><b><i>uxTaskGetStackHighWaterMark:</b></i> 2912 B <br><b><i>Total PSRAM:</b></i> 0 B <b>| <i>Free PSRAM:</b></i> 0 B<br><br><b><i>Local time:</i></b> Sun Jan 25 10:03:46 2026
[10:03:48]<b><i>Supla uptime:</i></b> 720 s
[10:03:59]Send: [53 55 50 4C 41 1B 49 00 00 00 28 00 00 00 10 00 00 00 8C EA 75 69 00 00 00 00 7B 0D 0E 00 00 00 00 00 ]
[10:03:59]Send: [53 55 50 4C 41 ]
[10:03:59]Recv: [53 55 50 4C 41 1B 28 00 00 00 32 00 00 00 10 00 00 00 7D DC 75 69 00 00 00 00 08 6F 0B 00 00 00 00 00 53 55 50 4C 41 ]
[10:04:24]Send: [53 55 50 4C 41 1B 4A 00 00 00 28 00 00 00 10 00 00 00 A5 EA 75 69 00 00 00 00 41 21 0E 00 00 00 00 00 ]
[10:04:24]Send: [53 55 50 4C 41 ]
[10:04:24]Recv: [53 55 50 4C 41 1B 29 00 00 00 32 00 00 00 10 00 00 00 96 DC 75 69 00 00 00 00 66 82 0B 00 00 00 00 00 53 55 50 4C 41 ]
[10:04:44][775892][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[10:04:44][775893][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[10:04:44]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 10
[10:04:44]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[10:04:44]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 10, rx_time: 0
[10:04:44][775894][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[10:04:44][775895][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[10:04:44][775895][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[10:04:44][775896][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[10:04:44][775896][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 14 size: 7
[10:04:44][775897][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[10:04:44][775897][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x36 
[10:04:44][775897][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[10:04:44][775898][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[10:04:44][775898][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[10:04:44][775898][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x01 
[10:04:44][775899][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[10:04:44][775899][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[10:04:44][775900][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[10:04:44][775901][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[10:04:44][775901][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[10:04:44][775902][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[10:04:44][775903][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[10:04:44][775903][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[10:04:44][775904][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 7
[10:04:44][775904][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[10:04:44][775904][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0x36
[10:04:44][775905][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x1
[10:04:44][775905][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x4
[10:04:44][775906][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[10:04:44][775906][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x1
[10:04:44][775907][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x0
[10:04:44][775907][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[10:04:44][775908][I][z2s_device_tuya_custom_cluster.cpp:2129] processMoesShadesDriveMotorDataReport(): state = 0
[10:04:44][776098][D][ZigbeeCore.cpp:504] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[10:04:44][776099][D][ZigbeeCore.cpp:508] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 1, dst_addr_mode: 255
[10:04:44]APSDE INDICATION - src_addr_mode: 23, cluster_id: 0xef00, asdu_length: 13
[10:04:44]APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0xbb17
[10:04:44]APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 10, rx_time: 0
[10:04:44][776101][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0xef00, command id: 1
[10:04:44][776101][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x1, dst endpoint 0x1
[10:04:44][776102][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 0, disable_default_response 1, is_manuf_specific 0
[10:04:44][776102][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[10:04:44][776102][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 15 size: 10
[10:04:44][776103][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[10:04:44][776103][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x37 
[10:04:44][776104][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x02 
[10:04:44][776104][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x02 
[10:04:44][776104][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[10:04:44][776105][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04 
[10:04:44][776105][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[10:04:44][776105][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[10:04:44][776106][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00 
[10:04:44][776106][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x64 
[10:04:44][776106][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0xbb17, 0xbb17, 0x0, 0x0
[10:04:44][776107][I][z2s_devices_table.cpp:4312] Z2S_onCustomCmdReceive(): A4:C1:38:1C:73:1D:2A:09, endpoint 0x1, cluster 0xef00, cmd id 0x1
[10:04:44][776107][I][z2s_devices_table.cpp:4326] Z2S_onCustomCmdReceive(): z2s_channels_table[channel_number_slot].Supla_channel 0x0
[10:04:45][776108][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[10:04:45][776109][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1040) callback
[10:04:45][776109][I][ZigbeeHandlers.cpp:484] zb_cmd_custom_cluster_req_handler(): Receive custom command: 1 from address 0xbb17
[10:04:45][776110][I][ZigbeeHandlers.cpp:485] zb_cmd_custom_cluster_req_handler(): Frame control 0x0
[10:04:45][776110][I][ZigbeeHandlers.cpp:486] zb_cmd_custom_cluster_req_handler(): Payload size: 10
[10:04:45][776111][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x0] = 0x0
[10:04:45][776111][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x1] = 0x37
[10:04:45][776112][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x2] = 0x2
[10:04:45][776112][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x3] = 0x2
[10:04:45][776113][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x4] = 0x0
[10:04:45][776113][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x5] = 0x4
[10:04:45][776114][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x6] = 0x0
[10:04:45][776114][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x7] = 0x0
[10:04:45][776114][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x8] = 0x0
[10:04:45][776115][I][ZigbeeHandlers.cpp:488] zb_cmd_custom_cluster_req_handler(): Payload [0x9] = 0x64
[10:04:45][776115][I][z2s_device_tuya_custom_cluster.cpp:3001] processTuyaCustomCluster(): processing Tuya custom cluster 0xEF00, command id 0x1
[10:04:45][776116][I][z2s_device_tuya_custom_cluster.cpp:2158] processMoesShadesDriveMotorDataReport(): position = 100
[10:04:48][780091][I][Z2S_Gateway.ino:944] loop(): New UTC time 822650686, new local time 822650686
[10:04:48][780092][I][Z2S_Gateway.ino:976] loop(): 
[10:04:48]Local Time Cluster Time status attribute 2
[10:04:48]UTC time attribute 822650686
[10:04:48]local time attribute 822650686
[10:04:48][780094][I][z2s_web_gui.cpp:843] fillMemoryUptimeInformation(): Memory & uptime information <b><i>Flash chip real size:</b></i> 8388608 B <b>| <i>Free Sketch Space:</b></i> 3407872 B<br><b><i>HeapSize:</b></i> 358028 B <b>| <i>FreeHeap:</b></i> 56080 B <b>| <i>MinimalFreeHeap:</b></i> 43484 B <b>| <i>MaxAllocHeap:</b></i> 40948 B<br><b><i>uxTaskGetStackHighWaterMark:</b></i> 2912 B <br><b><i>Total PSRAM:</b></i> 0 B <b>| <i>Free PSRAM:</b></i> 0 B<br><br><b><i>Local time:</i></b> Sun Jan 25 10:04:46 2026
[10:04:48]<b><i>Supla uptime:</i></b> 780 s
[10:04:49]Send: [53 55 50 4C 41 1B 4B 00 00 00 28 00 00 00 10 00 00 00 BE EA 75 69 00 00 00 00 1D 35 0E 00 00 00 00 00 ]
[10:04:49]Send: [53 55 50 4C 41 ]
[10:04:49]Recv: [53 55 50 4C 41 1B 2A 00 00 00 32 00 00 00 10 00 00 00 AF DC 75 69 00 00 00 00 5D 99 0B 00 00 00 00 00 53 55 50 4C 41 ]
[10:04:52]
Serial port closed!


a przy ponownym włączeniu bramki wysyła sygnał zamknij roletę jak bramka startuje
Top
LukiSpajder
Posts: 1548
Joined: Tue Aug 18, 2020 2:22 pm
Has thanked: 25 times
Been thanked: 34 times

Post

Jak będziesz miał czas doszlifować ten sterownik to mam go zamontowanego już fizycznie z roleta . Okazuje się że te przyciski w apce po prawej działają poprawnie góra to góra , dół to dół .
A reszta to tak jak na rzucie ekranu z apki .
Top

Return to “Bramka ZigBee”