Najczęstsze pytania i odpowiedzi [bramka ZigBee]

Moderator: vajera

djack2017
Posts: 784
Joined: Mon Nov 27, 2017 7:36 am
Been thanked: 1 time

Post

vajera wrote: Sun Jul 26, 2026 7:27 pm
djack2017 wrote: Fri Jul 24, 2026 8:24 am Sytuacja wygląda tak:
1. serwer prywatny supli w wersji 25.12.02
2. jak wgram starszy firmware do bramki i wyłączę w konfiguracji kontrolę certyfikatu to bramka w supli się zarejestruje
3. jak wgram najnowszy firmware do bramki i wyłączę w konfiguracji kontrolę certyfikatu to bramka w supli się nie zarejestruje
Jak wygląda sytuacja w przypadku włączenia weryfikacji certyfikatu?
Jesteś w stanie ustalić numer ostatniej działającej wersji?
Ja używam starej wersji:
Image2.png
Do niej dorobiłem obsługę serwera zabbix. Ta wersja obsługuje interesujące mnie sterowniki: termometr sonoff, miernik shelly 4 oraz zawór podlewania sonoff. Wgrłem nowy software z ciekawości bo nie wiem czy ta wersja, którą mam obsługuje czujnik deszczu (ale w sumie nie jest to takie ważne). Nie chcę wciąż ściągać nowych plików oprogramowania bramki i je modyfikować pod kątem zabbixa. A zapewne @vajera nie byłby zainteresowany "pull requestem" (choć dodatkowa funkcjonalność nie koliduje z jego kodem).
NIe jestem w stanie ustalić ostatniej działającej wersji bo skoro działa ta, której używam, to nie mam potrzeby aktualizacji (także z powodów j/w).
You do not have the required permissions to view the files attached to this post.
__________________________________________________________
Specjalizowane oprogramowanie do sterowników Sonoff, Gosund, Blitzwolf, Shelly i innych:
https://djack.com.pl/modules.php?name=Downloads&d_op=viewdownload&cid=54
Top
djack2017
Posts: 784
Joined: Mon Nov 27, 2017 7:36 am
Been thanked: 1 time

Post

lesny8 wrote: Sun Jul 26, 2026 9:13 pm Problem nie leży zatem w bramce Z2S a w Twoj wersji serwera Supli. @vajera ostatnio dodawał np. wsparcie dla kanałów CCT i RGB+CCT, a to pewnie jest dostępne w nowszej wersji proto. Zgaduję, bo nie sprawdzałem.
Ja nie jestem zwolennikiem ciągłych aktualizacji, jeśli wersja, którą mam, pracuje poprawnie. Byłoby to "sztuką dla sztuki". Jak będę potrzebował czegoś nowego, czego nie ma obecna moja wersja, to się nad tym pochylę. Z resztą @vajera jest dosyć "płodny" i nowe wersje pojawiają się praktycznie "co chwilę".
__________________________________________________________
Specjalizowane oprogramowanie do sterowników Sonoff, Gosund, Blitzwolf, Shelly i innych:
https://djack.com.pl/modules.php?name=Downloads&d_op=viewdownload&cid=54
Top
User avatar
uchnast.michal
Posts: 1334
Joined: Tue Jun 04, 2019 11:37 am
Has thanked: 7 times

Post

adamigo wrote: Thu Mar 05, 2026 9:56 pm
Dodatkowo Korzysta ktoś z Was z gniazdka z licznikiem Ikea Inspelning.

Gniazdko działa bez zarzutu niestety nie widzę żadnych danych z licznika, miał ktoś podobną sytuację ?
Korzystam, to moje gniazdko testowe, ono powinno reagować na polecenie configure-reporting, chociaż z tego, co pamiętam, to chyba raportowało out of the box?
Problemem było 0 w timings panel. Może warto z automatu wstawić liczbę większą niż 0 by działało od strzała ?

Dodatkowe pytanie jakie masz ustawione u siebie odświeżanie ?
Dzisiaj kupiłem dwa z pomiarem energii ale bramka nie znajduje.
Wersja Z2S-1.5.148-31/07/26
Top
User avatar
vajera
Posts: 7303
Joined: Wed Oct 31, 2018 7:58 am
Location: Biedrusko
Has thanked: 293 times
Been thanked: 162 times

Post

uchnast.michal wrote: Sat Aug 22, 2026 5:15 pm Dzisiaj kupiłem dwa z pomiarem energii ale bramka nie znajduje.
Wersja Z2S-1.5.148-31/07/26
Jaki masz komunikat w GUI w polu Last binding result?
Bramka Zigbee <=> SUPLA
Więcej informacji tutaj:
https://forum.supla.org/viewforum.php?f=127
FAQ https://forum.supla.org/viewtopic.php?t=17277
Top
User avatar
uchnast.michal
Posts: 1334
Joined: Tue Jun 04, 2019 11:37 am
Has thanked: 7 times

Post

Piewsze z 2 było uszkodzone, spróbowałem drugie i ładnie się dodało.
PS
W Last binding result nie mam nic tylko ...

Dziękuję za pomoc.
Top
User avatar
vajera
Posts: 7303
Joined: Wed Oct 31, 2018 7:58 am
Location: Biedrusko
Has thanked: 293 times
Been thanked: 162 times

Post

uchnast.michal wrote: Sat Aug 22, 2026 6:57 pm Piewsze z 2 było uszkodzone, spróbowałem drugie i ładnie się dodało.
Może spróbuj to pierwsze zresetować do ustawień fabrycznych? Chyba, że jest fizycznie uszkodzone?
PS
W Last binding result nie mam nic tylko ...
Tam zasadniczo będzie tylko rezultat nieudanego parowania, tzn. dane nierozpoznanego urządzenia.
Dziękuję za pomoc.
Di niente.
Bramka Zigbee <=> SUPLA
Więcej informacji tutaj:
https://forum.supla.org/viewforum.php?f=127
FAQ https://forum.supla.org/viewtopic.php?t=17277
Top
Kwicol
Posts: 121
Joined: Sun Jan 03, 2021 3:08 pm

Post

Witam.
C6 8M po wgraniu full-a zaświeca się zielona i zaczyna migać szybko biała ale nie rozgłasza sieci do konfiguracji?Flash czyszczony i wgrywany blank 8mega nie pomaga.Spotkał się ktoś z taki problemem ?
Pozdrawiam.

Code: Select all

=========== After Setup End =============
                                         LittleFsConfig: writing to file "/supla                                                                                                             -dev.cfg"
LittleFsConfig: writing to file "/supla-dev.cfg.bak"
Reset requested. Reset device
[  4938][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  4939][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  4939][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
LittleFsConfig: writing to file "/supla-dev.cfg"
LittleFsConfig: writing to file "/supla-dev.cfg.bak"
[  5056][V][AP.cpp:112] _onApEvent(): AP Stopped
[  5057][V][AP.cpp:108] _onApEvent(): AP Started
[  5057][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 131 - AP_STOP
[  5058][V][AP.cpp:88] _onApArduinoEvent(): Arduino AP Event: 131 - AP_STOP
[  5058][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 130 - AP_START
[  5059][V][AP.cpp:88] _onApArduinoEvent(): Arduino AP Event: 130 - AP_START
[  5059][V][AP.cpp:112] _onApEvent(): AP Stopped
[  5060][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 131 - AP_STOP
[  5060][V][AP.cpp:88] _onApArduinoEvent(): Arduino AP Event: 131 - AP_STOP
[  5064][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 100 - WIFI_OFF
[  5064][V][NetworkInterface.cpp:264] destroyNetif(): Unregistered event handler
[  5065][E][STA.cpp:530] disconnect(): STA disconnect failed! 0x3001: ESP_ERR_WIFI_NOT_INIT
Resetting in 0.5s...
See you soon!
ESP-ROM:esp32c6-20220919
Build:Sep 19 2022
rst:0xc (SW_CPU),boot:0xc (SPI_FAST_FLASH_BOOT)
Saved PC:0x4001975a
SPIWP:0xee
mode:DIO, clock div:2
load:0x40875730,len:0x12e0
load:0x4086b910,len:0xdc8
load:0x4086e610,len:0x3180
entry 0x4086b910
[     1][V][ZigbeeEP.cpp:22] ZigbeeEP(): Endpoint: 1
[     9][V][NetworkServer.h:41] NetworkServer(): NetworkServer::NetworkServer(port=23, ...)
[    17][V][NetworkServer.h:41] NetworkServer(): NetworkServer::NetworkServer(port=1234, ...)
[    40][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type USB_DM (38) successfully set to 0x420b2dde
[    52][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 12 successfully set to type USB_DM (38) with bus 0x40820828
[    62][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type USB_DP (39) successfully set to 0x420b2dde
[    74][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 13 successfully set to type USB_DP (39) with bus 0x40820828
=========== Before Setup Start ===========
                                          Chip Info:
                                                    ------------------------------------------
                                                                                                Model             : ESP32-C6
                                                                                                                              Package           : 0
                                                                                                                                                     Revision          : 0.02
                                                                                                                                                                               Cores             : 1
         CPU Frequency     : 160 MHz
                                      XTAL Frequency    : 40 MHz
                                                                  Features Bitfield : 0x00000052
                                                                                                  Embedded Flash    : No
                                                                                                                          Embedded PSRAM    : No
                                                                                                                                                  2.4GHz WiFi       : Yes
                                                                                                                                                                           Classic BT        : No
      BT Low Energy     : Yes
                               IEEE 802.15.4     : Yes
                                                      ------------------------------------------
                                                                                                INTERNAL Memory Info:
                                                                                                                     ------------------------------------------
                                                                                                                                                                 Total Size        :   358268 B ( 349.9 KB)
                Free Bytes        :   302212 B ( 295.1 KB)
                                                            Allocated Bytes   :    42736 B (  41.7 KB)
                                                                                                        Minimum Free Bytes:   302212 B ( 295.1 KB)
                                                                                                                                                    Largest Free Block:   286708 B ( 280.0 KB)
 ------------------------------------------
                                           Flash Info:
                                                      ------------------------------------------
                                                                                                  Chip Size         :  8388608 B (8 MB)
                                                                                                                                         Block Size        :    65536 B (  64.0 KB)
                                                                                                                                                                                     Sector Size       :     4096 B (   4.0 KB)
                                    Page Size         :      256 B (   0.2 KB)
                                                                                Bus Speed         : 80 MHz
                                                                                                            Flash Frequency   : 80 MHz (source: 80 MHz, divider: 1)
                                                                                                                                                                     Bus Mode          : QIO
                                                                                                                                                                                            ------------------------------------------
                                         Partitions Info:
                                                         ------------------------------------------
                                                                                                                   nvs : addr: 0x00009000, size:    20.0 KB, type: DATA, subtype: NVS
                                                                                                                                                                                                 otadata : addr: 0x0000E000, size:     8.0 KB, type: DATA, subtype: OTA
                                                                                         app0 : addr: 0x00010000, size:  3328.0 KB, type:  APP, subtype: OTA_0
                                                                                                                                                                             app1 : addr: 0x00350000, size:  3328.0 KB, type:  APP, subtype: OTA_1
                                                                  spiffs : addr: 0x00690000, size:  1384.0 KB, type: DATA, subtype: SPIFFS
                                                                                                                                                   zb_storage : addr: 0x007EA000, size:    16.0 KB, type: DATA, subtype: FAT
                                            zb_fct : addr: 0x007EE000, size:     4.0 KB, type: DATA, subtype: FAT
                                                                                                                              rcp_fw : addr: 0x007EF000, size:     4.0 KB, type: DATA, subtype: SPIFFS
                    coredump : addr: 0x007F0000, size:    64.0 KB, type: DATA, subtype: COREDUMP
                                                                                                ------------------------------------------
                                                                                                                                          Software Info:
                                                                                                                                                        ------------------------------------------
       Compile Date/Time : Sep  2 2026 14:28:15
                                                 Compile Host OS   : linux
                                                                            ESP-IDF Version   : v5.5.2-249-gf56bea3d1f
                                                                                                                        Arduino Version   : 3.3.6
                                                                                                                                                 ------------------------------------------
                                                                                                                                                                                           Board Info:
         ------------------------------------------
                                                     Arduino Board     : ESP32C6_DEV
                                                                                      Arduino Variant   : esp32c6
                                                                                                                   Arduino FQBN      : esp32:esp32:esp32c6:PartitionScheme=zigbee_zczr_8MB,ZigbeeMode=zczr,FlashSize=8M,CDCOnBoot=cdc,DebugLevel=verbose
                                                           ============ Before Setup End ============
                                                                                                     [   197][V][esp32-hal-periman.c:251] perimanClearBusDeinit(): Deinit function for type UART_RX (2) cleared
[   197][V][esp32-hal-periman.c:251] perimanClearBusDeinit(): Deinit function for type UART_TX (3) cleared
[   198][V][esp32-hal-periman.c:251] perimanClearBusDeinit(): Deinit function for type UART_CTS (4) cleared
[   198][V][esp32-hal-periman.c:251] perimanClearBusDeinit(): Deinit function for type UART_RTS (5) cleared
[   199][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 17 successfully set to type UART_RX (2) with bus 0x40817058
[   200][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x420b9038
[   200][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 16 successfully set to type UART_TX (3) with bus 0x40817058
[   201][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x420b8efe
[   201][I][Z2S_Gateway.ino:507] setup(): setup start
[   202][I][z2s_devices_table.cpp:12733] printSizeOfClasses():
Relay 136 - VirtualRelay 144 - Z2S_VirtualRelay 200
HvacBase 1032 - HvacBaseEE 1040 - Z2S_trv_interface 212
VirtualSceneSwitch 168
Z2S_GPM 224
IPAddress 28
NetworkServer 44
NetworkClient 52
ZigbeeGateway 256
Supla::Action 4
Supla::Event 4
[   230][I][Z2S_Gateway.ino:538] setup(): Sanity check time 27
[   230][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type GPIO (1) successfully set to 0x420b6154
[   231][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 9 successfully set to type GPIO (1) with bus 0xa
[   232][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type GPIO (1) successfully set to 0x420b6154
[   232][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 3 successfully set to type GPIO (1) with bus 0x4
[   233][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type GPIO (1) successfully set to 0x420b6154
[   233][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 14 successfully set to type GPIO (1) with bus 0xf
Storage initialization
EEPROM: Read 8 bytes [53 55 50 4C 41 01 00 01 ] (offset 0)
Storage: Number of sections 1
Reading section: 0
EEPROM: Read 7 bytes [03 06 00 08 95 08 95 ] (offset 8)
Section type: 3; size: 6
storedCRC 38152, CRC calc 38152
LittleFsConfig: file "/supla-dev.cfg" size 210
LittleFsConfig: initializing storage from file...
LittleFsConfig: init result success
LittleFsConfig: writing to file "/supla-dev.cfg"
LittleFsConfig: writing to file "/supla-dev.cfg.bak"
Channel[110] initial caption set to 'Gateway sensors notifications'
Channel[110]: setDefaultFunction: 130
Button[0] setHoldTime: 2000
Button[0] setMulticlickTime: 500
Button[0]::configureAsConfigButton
Button[0] setHoldTime: 5000
Button[0] setMulticlickTime: 300
Listing directory: /
                      FILE: supla-dev.cfg.bak  SIZE: 210 LAST WRITE: 1970-01-01 00:00:06
                                                                                          FILE: supla-dev.cfg  SIZE: 210 LAST WRITE: 1970-01-01 00:00:06
                                                                                                                                                          FILE: version.dat  SIZE: 25 LAST WRITE: 1970-01-01 00:00:02
                          DIR : z2s_gatewayLAST WRITE: 1969-12-31 23:59:59
                                                                          Listing directory: /z2s_gateway
                                                                                                           FILE: actions_index_table.z2s  SIZE: 32 LAST WRITE: 1970-01-01 00:00:06
                                                                                                                                                                                    FILE: channels_table_v2.bak  SIZE: 15360 LAST WRITE: 1970-01-01 00:00:03
                                                                 FILE: channels_table_v2.z2s  SIZE: 15360 LAST WRITE: 1970-01-01 00:00:03
                                                                                                                                           FILE: pushover_messages_index_table.z2s  SIZE: 32 LAST WRITE: 1970-01-01 00:00:06
                                 FILE: zb_devices_table_v2.bak  SIZE: 3840 LAST WRITE: 1970-01-01 00:00:03
                                                                                                            FILE: zb_devices_table_v2.z2s  SIZE: 3840 LAST WRITE: 1970-01-01 00:00:03
                                                                                                                                                                                     Listing directory: /
              FILE: supla-dev.cfg.bak  SIZE: 210 LAST WRITE: 1970-01-01 00:00:06
                                                                                  FILE: supla-dev.cfg  SIZE: 210 LAST WRITE: 1970-01-01 00:00:06
                                                                                                                                                  FILE: version.dat  SIZE: 25 LAST WRITE: 1970-01-01 00:00:07
                  DIR : z2s_gatewayLAST WRITE: 1969-12-31 23:59:59
                                                                  Listing directory: /z2s_gateway
                                                                                                   FILE: actions_index_table.z2s  SIZE: 32 LAST WRITE: 1970-01-01 00:00:06
                                                                                                                                                                            FILE: channels_table_v2.bak  SIZE: 15360 LAST WRITE: 1970-01-01 00:00:03
                                                         FILE: channels_table_v2.z2s  SIZE: 15360 LAST WRITE: 1970-01-01 00:00:03
                                                                                                                                   FILE: pushover_messages_index_table.z2s  SIZE: 32 LAST WRITE: 1970-01-01 00:00:06
                         FILE: zb_devices_table_v2.bak  SIZE: 3840 LAST WRITE: 1970-01-01 00:00:03
                                                                                                    FILE: zb_devices_table_v2.z2s  SIZE: 3840 LAST WRITE: 1970-01-01 00:00:03
                                                                                                                                                                             [   498][E][z2s_little_fs.cpp:246] Z2S_getFileSize(): Z2S LittleFs: failed to open file "/zigbee_ota/zigbee_ota_file.ota"
[   499][I][Z2S_Gateway.ino:639] setup(): OTA file size 0
[   501][E][z2s_little_fs.cpp:163] Z2S_loadBufferFromFile(): Z2S LittleFs: failed to open file "/zigbee_ota/zigbee_ota_file.ota" for read
[   502][I][Z2S_Gateway.ino:645] setup():
upgrade_file_id = 0xFFFFFFFF, header_version = 0xFFFF, header_length = 65535
field_control = 0, manufacturer_id = 0x0000, image_type = 0x7058
file_version = 0x00004081, stack_version = 0, image_size = 0

[   503][W][LittleFS.cpp:59] begin(): LittleFS Already Mounted!
[   509][I][z2s_devices_table.cpp:1720] Z2S_loadZbDevicesTable():
Z2S_getZbDevicesTableSize 3840
sizeof(z2s_zb_devices_table) 3840
sizeof(z2s_zb_device_params_t) 120

[   510][W][LittleFS.cpp:59] begin(): LittleFS Already Mounted!
[   519][I][z2s_devices_table.cpp:1977] Z2S_loadZbDevicesTable(): Zigbee devices table load success!
[   520][W][LittleFS.cpp:59] begin(): LittleFS Already Mounted!
[   526][I][z2s_devices_table.cpp:752] Z2S_loadChannelsTable(): Z2S_getChannelsTableSize 15360, sizeof(z2s_channels_table) 15360, sizeof(z2s_device_params_t) 120, sizeof(bool)1
[   527][W][LittleFS.cpp:59] begin(): LittleFS Already Mounted!
[   538][I][z2s_devices_table.cpp:976] Z2S_loadChannelsTable(): Channels table load success!
[   539][I][z2s_devices_table.cpp:2276] Z2S_initSuplaChannels(): initSuplaChannels starting
[   539][I][Z2S_common.h:377] setZ2SChannelUID(): _z2s_channel_uid 0x00000000
[   539][I][Z2S_common.h:314] listCores(): Core ptr 0x408340F4, Element ptr 0x408340E4, name GATEWAY EVENTS,
short address 0x0000, channel #4294967295, sub id 0

[   540][W][LittleFS.cpp:59] begin(): LittleFS Already Mounted!
[   549][I][Z2Scommon.cpp:112] Z2S_loadIndexTable(): Index table (pushover_messages_index_table.z2s) load SUCCESS!
[   549][I][z2s_devices_table.cpp:3008] Z2S_initPushoverMessages(): Pushover messages index table loaded, messages count = 0
[   550][I][Z2S_Gateway.ino:695] setup(): Z2S_REBUILD_CHANNELS_ON_START not configured - turning off
[   550][I][Z2S_local_action_handlers.cpp:354] handleAction(): &&&&&&&&&&&&&&&&&&&&&&&&&& event 16418, action 0
[   551][I][Z2S_local_action_handlers.cpp:354] handleAction(): &&&&&&&&&&&&&&&&&&&&&&&&&& event 16433, action 0
[   551][W][LittleFS.cpp:59] begin(): LittleFS Already Mounted!
[   560][I][Z2Scommon.cpp:112] Z2S_loadIndexTable(): Index table (actions_index_table.z2s) load SUCCESS!
[   560][I][z2s_devices_table.cpp:2720] Z2S_initSuplaActions(): actions number: 0
[   561][I][Z2S_Gateway.ino:360] enableZ2SNotifications(): enabling Zigbee Gateway notifications
[   561][D][ZigbeeCore.cpp:100] addEndpoint(): Endpoint: 1, Device ID: 0x0050
[   562][I][Z2S_Gateway.ino:742] setup(): Z2S_ENABLE_GUI_ON_START_V2 = 1
[   562][I][Z2S_Gateway.ino:759] setup(): Z2S_FORCE_CONFIG_ON_START = 1
[   563][I][Z2S_Gateway.ino:773] setup(): Z2S_GUI_ON_START_DELAY_V2 = 10 s
[   563][I][Z2S_Gateway.ino:789] setup(): Z2S_AUTO_CONNECTION_RESET_TIMEOUT = 0 s
[   563][I][Z2S_Gateway.ino:809] setup(): Z2S_GATEWAY_MDNS_LOCAL_NAME not configured - using default
[   564][I][Z2S_Gateway.ino:821] setup(): Z2S_USE_NEW_AT_MODEL not configured - turning on
SD: initial mode: Start in cfg mode (legacy, deprected)
[   564][I][Z2S_Gateway.ino:857] setup(): starting Supla WebServer
[   565][V][NetworkServer.h:41] NetworkServer(): NetworkServer::NetworkServer(port=80, ...)
[   565][V][WebServer.cpp:49] WebServer(): WebServer::Webserver(port=80)

 *** Supla - starting initialization (platform 0)
SD: add flag DEVICE_CONFIG_SUPPORTED
SD: add flag CALCFG_RESTART_DEVICE

 *** Supla - Config initalization
SD: add flag CALCFG_ENTER_CFG_MODE
SD: add flag CALCFG_FACTORY_RESET_SUPPORTED
Automatic firmware update is disabled
Device mode: 0
Config incomplete: missing Wi-Fi SSID
LAST STATE ADDED: Missing Wi-Fi SSID
Config incomplete: missing Wi-Fi password
LAST STATE ADDED: Missing Wi-Fi password
Config incomplete: missing server
Config incomplete: missing email
Security level: Supla CA

 *** Supla - Config load for elements
SD: add flag CALCFG_IDENTIFY_DEVICE
RemoteDeviceConfig: Registering field 0x000000001
RemoteDeviceConfig: Registering field 0x000000010
Clock: automaticTimeSync: 1
Channel[110] function missing. Using SW defaults
Button[0] don't load config
PowerCycle: 1 (enabled)
 *** Supla - Config load for elements done

 *** Supla - Load state storage
Validating storage state section with current device configuration
Storage state section validation successful
EEPROM: Read 1 bytes [6E ] (offset 15)
EEPROM: Read 4 bytes [00 00 00 00 ] (offset 16)
EEPROM: Read 1 bytes [00 ] (offset 20)
Relay[110] restored relay state: OFF
Relay[110] restored remaining countdown timer durationMs: 0
 *** Supla - Load state storage done

 *** Supla - Init elements
[   570][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[   571][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_TX (10) successfully set to 0x420b7af6
[   571][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_RX (11) successfully set to 0x420b7af6
[   572][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 8 successfully set to type RMT_TX (10) with bus 0x408371bc
[   574][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[   574][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[   575][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type GPIO (1) successfully set to 0x420b6154
[   576][V][esp32-hal-rmt.c:142] _rmtDetachBus(): Detaching RMT GPIO Bus
[   576][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 8 successfully set to type INIT (0) with bus 0x0
[   577][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 8 successfully set to type GPIO (1) with bus 0x9
Relay[110] turn OFF (duration 0 ms)
Relay[110] init done, storedTurnOnDurationMs 0
Button[0]: Initialized: pin 9, pullUp 1, activeHigh 0, state 1
 *** Supla - Init elements done

Config incomplete: deviceMode = CONFIG
LAST STATE ADDED: Missing server address
[   578][I][Z2S_Gateway.ino:168] supla_callback_bridge(): event(0x23), action(0x4010)
[   579][I][Z2S_Gateway.ino:202] supla_callback_bridge(): Supla device status changed to 3
[   579][I][Z2S_local_action_handlers.cpp:354] handleAction(): &&&&&&&&&&&&&&&&&&&&&&&&&& event 35, action 24576
Current status: [3] Missing server address
LAST STATE ADDED: Missing email address
[   580][I][Z2S_Gateway.ino:168] supla_callback_bridge(): event(0x23), action(0x4010)
[   581][I][Z2S_Gateway.ino:202] supla_callback_bridge(): Supla device status changed to 32
[   581][I][Z2S_local_action_handlers.cpp:354] handleAction(): &&&&&&&&&&&&&&&&&&&&&&&&&& event 35, action 24576
Current status: [32] Missing email address
GUID: DB5E59711B9665437EDE90D310115B07
Device name: Zigbee <=> Supla Gateway
Device software version: Z2S-1.5.164-02/09/26
 *** Supla - Initializing network layer
[Wi-Fi] Network AP/hostname: SUPLA-ZIGBEE-GATE-588C81305A0C
Using Supla protocol version 28
[   582][I][Z2S_Gateway.ino:168] supla_callback_bridge(): event(0x23), action(0x4010)
[   583][I][Z2S_Gateway.ino:202] supla_callback_bridge(): Supla device status changed to 5
[   583][I][Z2S_local_action_handlers.cpp:354] handleAction(): &&&&&&&&&&&&&&&&&&&&&&&&&& event 16393, action 0
[   584][I][Z2S_local_action_handlers.cpp:354] handleAction(): &&&&&&&&&&&&&&&&&&&&&&&&&& event 35, action 24576
Current status: [5] SuplaDevice initialized
Config incomplete: deviceMode = CONFIG
Wi-Fi SSID missing
[Wi-Fi] setConfigMode
WiFi: enter config mode with SSID: "SUPLA-ZIGBEE-GATE-588C81305A0C"
[   593][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 101 - WIFI_READY
[   686][V][AP.cpp:108] _onApEvent(): AP Started
[   687][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 130 - AP_START
[   687][V][AP.cpp:88] _onApArduinoEvent(): Arduino AP Event: 130 - AP_START
[   697][V][AP.cpp:112] _onApEvent(): AP Stopped
[   698][V][AP.cpp:108] _onApEvent(): AP Started
[   698][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 131 - AP_STOP
[   698][V][AP.cpp:88] _onApArduinoEvent(): Arduino AP Event: 131 - AP_STOP
[   699][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 130 - AP_START
[   699][V][AP.cpp:88] _onApArduinoEvent(): Arduino AP Event: 130 - AP_START
Starting local web server
LAST STATE ADDED: Config mode
[   701][I][Z2S_Gateway.ino:168] supla_callback_bridge(): event(0x23), action(0x4010)
[   701][I][Z2S_Gateway.ino:202] supla_callback_bridge(): Supla device status changed to 40
[   702][I][Z2S_local_action_handlers.cpp:354] handleAction(): &&&&&&&&&&&&&&&&&&&&&&&&&& event 35, action 24576
Current status: [40] Config mode
 *** Supla - Initialization done

 *** Self-test ***
TEST: ManufacturerID is 0
TEST failed: ProductID is empty
TEST failed: missing public RSA key
TEST failed: automatic firmware update is disabled
TEST failed: config encryption is disabled
TEST failed: invalid certificates format
TEST failed: security log is disabled
TEST failed: initial mode is set to config mode
 *** Self-test done ***
[   703][E][esp32-hal-misc.c:165] disableCore0WDT(): Failed to remove Core 0 IDLE task from WDT
E (2241) task_wdt: delete_entry(240): task not found
                                                    E (2242) task_wdt: delete_entry(240): task not found
                                                                                                        =========== After Setup Start ============
                                                                                                                                                  INTERNAL Memory Info:
                                                                                                                                                                       ------------------------------------------
                      Total Size        :   358268 B ( 349.9 KB)
                                                                  Free Bytes        :   242652 B ( 237.0 KB)
                                                                                                              Allocated Bytes   :    97632 B (  95.3 KB)
                                                                                                                                                          Minimum Free Bytes:   242040 B ( 236.4 KB)
         Largest Free Block:   225268 B ( 220.0 KB)
                                                   ------------------------------------------
                                                                                             GPIO Info:
                                                                                                       ------------------------------------------
                                                                                                                                                   GPIO : BUS_TYPE[bus/unit][chan]
                                                                                                                                                                                    --------------------------------------
                                    3 : GPIO
                                                 8 : GPIO
                                                              9 : GPIO
                                                                          12 : USB_DM
                                                                                         13 : USB_DP
                                                                                                        14 : GPIO
                                                                                                                     16 : UART_TX[0]
                                                                                                                                        17 : UART_RX[0]
                                                                                                                                                       ============ After Setup End =============
    [   728][W][LittleFS.cpp:59] begin(): LittleFS Already Mounted!
LittleFsConfig: writing to file "/supla-dev.cfg"
LittleFsConfig: writing to file "/supla-dev.cfg.bak"
Wi-Fi SSID missing
[Wi-Fi] setConfigMode
WiFi: resetting WiFi connection
[   748][E][STA.cpp:530] disconnect(): STA disconnect failed! 0xffffffff: ESP_FAIL
WiFi: enter config mode with SSID: "SUPLA-ZIGBEE-GATE-588C81305A0C"
Current status: [40] Config mode
LittleFsConfig: writing to file "/supla-dev.cfg"
[   756][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[   756][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_TX (10) successfully set to 0x420b7af6
[   757][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_RX (11) successfully set to 0x420b7af6
[   757][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 8 successfully set to type INIT (0) with bus 0x0
[   758][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 8 successfully set to type RMT_TX (10) with bus 0x40833d88
[   760][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[   761][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
LittleFsConfig: writing to file "/supla-dev.cfg.bak"
[   866][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[   866][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[   867][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[   975][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[   976][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[   976][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  1085][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  1086][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  1086][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  1195][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  1196][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  1196][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  1305][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  1306][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  1306][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  1415][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  1416][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  1417][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  1525][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  1526][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  1526][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  1635][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  1636][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  1637][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  1745][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  1746][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  1746][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  1855][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  1856][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  1856][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  1965][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  1966][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  1966][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  2075][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  2076][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  2076][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  2185][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  2186][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  2186][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  2295][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  2296][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  2297][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  2405][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  2406][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  2406][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  2515][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  2516][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  2516][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  2625][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  2626][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  2626][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  2735][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  2736][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  2736][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  2845][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  2846][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  2846][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  2955][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  2956][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  2957][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  3065][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  3066][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  3067][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  3175][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  3176][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  3177][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  3285][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  3286][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  3287][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  3395][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  3396][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  3396][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  3505][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  3506][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  3507][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  3615][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  3616][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  3616][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  3725][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  3726][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  3726][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  3835][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  3836][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  3836][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  3945][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  3946][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  3946][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  4055][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  4056][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  4056][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  4165][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  4166][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  4167][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  4275][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  4276][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  4276][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  4385][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  4386][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  4387][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  4495][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  4496][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  4497][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  4605][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  4606][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  4607][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  4715][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  4716][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  4717][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  4825][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  4826][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[  4827][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[  4935][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[  4936][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
Top

Return to “Bramka ZigBee”