thermostat with Oled display
-
Michal81
- Posts: 188
- Joined: Sun Feb 02, 2020 9:03 pm
The parts have arrived. I'm starting to submit my first project.
You do not have the required permissions to view the files attached to this post.
-
Michal81
- Posts: 188
- Joined: Sun Feb 02, 2020 9:03 pm
There are no resistors 10 ko. .
9.1 ko or 11. can I use another one? Which better?
9.1 ko or 11. can I use another one? Which better?
-
elmaya
- Posts: 1485
- Joined: Wed Jun 27, 2018 5:48 pm
- Location: El Saucejo - Sevilla
you can use any resistors for the Gpio16 Pullup with a value between 2.2K and 100KMichal81 wrote: Tue Feb 18, 2020 3:22 pm There are no resistors 10 ko. .
9.1 ko or 11. can I use another one? Which better?
Is that relay active at a high level?
It looks a lot like those that don't work with Esp8266.
-
Michal81
- Posts: 188
- Joined: Sun Feb 02, 2020 9:03 pm
Thank you for the information.
Sory, but bad I prepared for a photo. I have a similar controlled high state.
Sory, but bad I prepared for a photo. I have a similar controlled high state.
-
elmaya
- Posts: 1485
- Joined: Wed Jun 27, 2018 5:48 pm
- Location: El Saucejo - Sevilla
It's just a comment to prevent you from having problems with the operation.Michal81 wrote: Tue Feb 18, 2020 4:14 pm Thank you for the information.
Sory, but bad I prepared for a photo. I have a similar controlled high state.
-
Michal81
- Posts: 188
- Joined: Sun Feb 02, 2020 9:03 pm
Today's work effect. Tomorrow I will be uploading (trying to upload) soft ...
Today I am afraid to move it ..
Today I am afraid to move it ..
You do not have the required permissions to view the files attached to this post.
-
Michal81
- Posts: 188
- Joined: Sun Feb 02, 2020 9:03 pm
Should this set be powered separately or sufficient from a computer and a USB cable?
I uploaded soft, but nothing happens - the display is off, you can't see the chips in the wifi network.
Well, unless I loaded incorrectly ...
I have loaded one file called "supla_Termostst_oled_dimm_V04_DOUT_16Mbit". Do you still have to load any?
Settings below :
I uploaded soft, but nothing happens - the display is off, you can't see the chips in the wifi network.
Well, unless I loaded incorrectly ...
I have loaded one file called "supla_Termostst_oled_dimm_V04_DOUT_16Mbit". Do you still have to load any?
Settings below :
You do not have the required permissions to view the files attached to this post.
-
elmaya
- Posts: 1485
- Joined: Wed Jun 27, 2018 5:48 pm
- Location: El Saucejo - Sevilla
is in the name of the file: 16Mbit
you also have this image in the attached
it's 0x00000 and not 0x7E0000
you also have this image in the attached
it's 0x00000 and not 0x7E0000
You do not have the required permissions to view the files attached to this post.
-
Michal81
- Posts: 188
- Joined: Sun Feb 02, 2020 9:03 pm
Master, you're great.
The OLED display lit up .... and I didn't know that the file title was talking about settings - I'm doing this for the first time.
And for the future (a little after the topic of this post) - how do I know what to set in the window 0x0000, if not all softs have such a wonderful description as yours?
Our fun - probably in the evening.
Thank you.
This is how it looks now :
The OLED display lit up .... and I didn't know that the file title was talking about settings - I'm doing this for the first time.
And for the future (a little after the topic of this post) - how do I know what to set in the window 0x0000, if not all softs have such a wonderful description as yours?
Our fun - probably in the evening.
Thank you.
This is how it looks now :
You do not have the required permissions to view the files attached to this post.
-
Michal81
- Posts: 188
- Joined: Sun Feb 02, 2020 9:03 pm
I have not yet read the explanation regarding:
What values to set in Config ESP:
- Temp x 10
- Histerisis x 10
Update - can you leave it blank?
What values to set in Config ESP:
- Temp x 10
- Histerisis x 10
Update - can you leave it blank?