Brak zmiany stanu kanału z funkcją Deep Sleep.

endrju_88
Posts: 448
Joined: Tue Apr 25, 2023 1:02 pm
Has thanked: 3 times
Been thanked: 4 times

Post

Witam Suplowiczów. :) Od jakiegoś czasu testuję stację pogodową z funkcją Deep sleep. Czujniki jakie wykorzystuję to BME280 , BH1750 oraz czujnik deszczu FC-37. Usypianie ustawione na 20 min. Wszystko działa jak należy z wyjątkiem czujnika deszczu. Wykorzystuję jego wyjście D0 podłączone do Gpio12 ,D6 do Wemos D1 mini. Czujnik ma działać na zasadzie 0 , 1 ( nie pada ,pada ) , i tu jest problem. W cloudzie i w aplikacji na kom nie zmienia mi się ikona stanu kanału. Po wybudzeniu wemosa odczytuje wartości czujników i wysyła na serwer a czujnika deszczu nie. Konwerter czujnika zapala diody stanu wyjścia , czyli czujnik działa. Zmieniałem wyjścia ESP jak i samo ESP na 32 i bez rezultatu. Czy ta funkcja jest w SUPLA wyłączona ,że nie ma możliwości zmiany stanu kanału z krańcówki lub czujnika poziomu cieczy? Dodam ,że bez funkcji Deep sleep wszystko działa jak należy i ikony się zmieniają po polaniu wodą płytki czujnika. Proszę , czy ktoś z Was miał już taki problem? :?:
User avatar
klew
Posts: 13911
Joined: Thu Jun 27, 2019 12:16 pm
Location: Wrocław
Has thanked: 136 times
Been thanked: 137 times

Post

Czy możesz zebrać logi z urządzenie?
Najlepsze suple dla Twojego domu :mrgreen:
endrju_88
Posts: 448
Joined: Tue Apr 25, 2023 1:02 pm
Has thanked: 3 times
Been thanked: 4 times

Post

Klew , wybacz ale nie bardzo wiem o co pytasz. Logi? Nie wspomniałem w poprzednim zapytaniu , że binarkę generowaniem w GG a nie w Arduino. Może tu o to Tobie chodzi?
endrju_88
Posts: 448
Joined: Tue Apr 25, 2023 1:02 pm
Has thanked: 3 times
Been thanked: 4 times

Post

A może chodzi ci o to co wyrzuca na serialu w monitorze portu szeregowego ,po resecie modułu?
User avatar
klew
Posts: 13911
Joined: Thu Jun 27, 2019 12:16 pm
Location: Wrocław
Has thanked: 136 times
Been thanked: 137 times

Post

endrju_88 wrote: Tue Apr 25, 2023 4:05 pm A może chodzi ci o to co wyrzuca na serialu w monitorze portu szeregowego ,po resecie modułu?
Tak, najlepiej jakby było widać kilka wybudzeń oraz zmianę stanu tego czujnika
Najlepsze suple dla Twojego domu :mrgreen:
endrju_88
Posts: 448
Joined: Tue Apr 25, 2023 1:02 pm
Has thanked: 3 times
Been thanked: 4 times

Post

Ok. oto co pokazało z mokrym czujnikiem :


ets Jan 8 2013,rst cause:2, boot mode:(3,6)

load 0x4010f000, len 3460, room 16
tail 4
chksum 0xcc
load 0x3fff20b8, len 40, room 4
tail 4
chksum 0xc9
csum 0xc9
v000979f0
~ld
Config read
Key: 0 Value: ⸮⸮ķ⸮⸮7!g`⸮]⸮
Key: 1 Value: ⸮⸮⸮20⸮N79Q⸮⸮⸮⸮:
Key: 2 Value: wifi
Key: 3 Value: ssid
Key: 4 Value: admin
Key: 5 Value: haslo
Key: 6 Value: TEST z WEMOSEM
Key: 7 Value: svrxx.supla.org
Key: 8 Value: email
Key: 9 Value: 0
Key: 10 Value: 0
Key: 11 Value: 1
Key: 12 Value:
Key: 13 Value:
Key: 14 Value:
Key: 15 Value:
Key: 16 Value: 103
Key: 17 Value:
Key: 18 Value:
Key: 19 Value: 1,,,,,,,,,,,1,,,
Key: 20 Value:
Key: 21 Value: 1
Key: 22 Value:
Key: 23 Value:
Key: 24 Value: ,,,,,,,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 25 Value:
Key: 26 Value:
Key: 27 Value:
Key: 28 Value: 1,9,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 29 Value: 1,10,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 30 Value:
Key: 31 Value:
Key: 32 Value:
Key: 33 Value:
Key: 34 Value:
Key: 35 Value:
Key: 36 Value: 1,3,,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 37 Value:
Key: 38 Value:
Key: 39 Value:
Key: 40 Value:
Key: 41 Value:
Key: 42 Value:
Key: 43 Value:
Key: 44 Value:
Key: 45 Value:
Key: 46 Value:
Key: 47 Value:
Key: 48 Value:
Key: 49 Value: 21,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 50 Value: 0,,,,,,,,,,,,,,,,
Key: 51 Value: ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 52 Value: ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 53 Value:
Key: 54 Value:
Key: 55 Value:
Key: 56 Value:
Key: 57 Value:
Key: 58 Value: 1
Key: 59 Value: 0
Key: 60 Value:
Key: 61 Value: 20
Key: 62 Value:
Key: 63 Value:
Key: 64 Value: 0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 65 Value:
Key: 66 Value:
Key: 67 Value:
Key: 68 Value:
Key: 69 Value:
Key: 70 Value:
Key: 71 Value:
Key: 72 Value:
Key: 73 Value:
Key: 74 Value: 0.45
Key: 75 Value: 0.45
Key: 76 Value:
Key: 77 Value:
Key: 78 Value:
Key: 79 Value: 1
Key: 80 Value: 0
Key: 81 Value:
Key: 82 Value:
Key: 83 Value:
Key: 84 Value:
Key: 85 Value:
Key: 86 Value: 0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 87 Value: 0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 88 Value: 0
Key: 89 Value:
Key: 90 Value:
Supla - starting initialization
Storage initialization
readStorage: 8; Read: [53 55 50 4C 41 1 0 0 ]
Storage: Number of sections 0
Config storage not configured
Validating storage state section with current device configuration
Storage state section validation completed. Loading elements state...
Channel(2) value changed to 1008.73
Channel(1) value changed to temp(23.070000), humi(54.695312)
Channel(3) value changed to 0.0
Initializing network layer
Network AP/hostname: TEST-Z-WEMOSEM-
Using Supla protocol version 16
Current status: [5] SuplaDevice initialized
Enter normal mode
WiFi: establishing connection with SSID: ""
Connected BSSID: 80:CC:9C:34:BD:AB
local IP: 192.168.0.xxx
subnetMask: 255.255.255.0
gatewayIP: 192.168.0.1
Signal strength (RSSI): -57 dBm
Establishing NOT encrypted connection with: svrxx.supla.org (port: 2015)
Connected to Supla Server
Current status: [10] Register in progress
Device registered (activity timeout 120 s, server version: 19, server min version: 1)
Current status: [17] Registered and ready
Changing activity timeout to 2400
ESP to Sleep mode
WiFi station disconnected
endrju_88
Posts: 448
Joined: Tue Apr 25, 2023 1:02 pm
Has thanked: 3 times
Been thanked: 4 times

Post

A to wyświetla przy suchym czujniku :


ets Jan 8 2013,rst cause:2, boot mode:(3,6)

load 0x4010f000, len 3460, room 16
tail 4
chksum 0xcc
load 0x3fff20b8, len 40, room 4
tail 4
chksum 0xc9
csum 0xc9
v000979f0
~ld
Config read
Key: 0 Value: ⸮⸮ķ⸮⸮7!g`⸮]⸮
Key: 1 Value: ⸮⸮⸮20⸮N79Q⸮⸮⸮⸮:
Key: 2 Value: wifi
Key: 3 Value: ssid
Key: 4 Value: admin
Key: 5 Value: haslo
Key: 6 Value: TEST z WEMOSEM
Key: 7 Value: svrxx.supla.org
Key: 8 Value: email
Key: 9 Value: 0
Key: 10 Value: 0
Key: 11 Value: 1
Key: 12 Value:
Key: 13 Value:
Key: 14 Value:
Key: 15 Value:
Key: 16 Value: 103
Key: 17 Value:
Key: 18 Value:
Key: 19 Value: 1,,,,,,,,,,,1,,,
Key: 20 Value:
Key: 21 Value: 1
Key: 22 Value:
Key: 23 Value:
Key: 24 Value: ,,,,,,,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 25 Value:
Key: 26 Value:
Key: 27 Value:
Key: 28 Value: 1,9,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 29 Value: 1,10,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 30 Value:
Key: 31 Value:
Key: 32 Value:
Key: 33 Value:
Key: 34 Value:
Key: 35 Value:
Key: 36 Value: 1,3,,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 37 Value:
Key: 38 Value:
Key: 39 Value:
Key: 40 Value:
Key: 41 Value:
Key: 42 Value:
Key: 43 Value:
Key: 44 Value:
Key: 45 Value:
Key: 46 Value:
Key: 47 Value:
Key: 48 Value:
Key: 49 Value: 21,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 50 Value: 0,,,,,,,,,,,,,,,,
Key: 51 Value: ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 52 Value: ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 53 Value:
Key: 54 Value:
Key: 55 Value:
Key: 56 Value:
Key: 57 Value:
Key: 58 Value: 1
Key: 59 Value: 0
Key: 60 Value:
Key: 61 Value: 20
Key: 62 Value:
Key: 63 Value:
Key: 64 Value: 0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 65 Value:
Key: 66 Value:
Key: 67 Value:
Key: 68 Value:
Key: 69 Value:
Key: 70 Value:
Key: 71 Value:
Key: 72 Value:
Key: 73 Value:
Key: 74 Value: 0.45
Key: 75 Value: 0.45
Key: 76 Value:
Key: 77 Value:
Key: 78 Value:
Key: 79 Value: 1
Key: 80 Value: 0
Key: 81 Value:
Key: 82 Value:
Key: 83 Value:
Key: 84 Value:
Key: 85 Value:
Key: 86 Value: 0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 87 Value: 0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 88 Value: 0
Key: 89 Value:
Key: 90 Value:
Supla - starting initialization
Storage initialization
readStorage: 8; Read: [53 55 50 4C 41 1 0 0 ]
Storage: Number of sections 0
Config storage not configured
Validating storage state section with current device configuration
Storage state section validation completed. Loading elements state...
Channel(0) value changed to 1
Channel(2) value changed to 1008.71
Channel(1) value changed to temp(23.170000), humi(56.889648)
Channel(3) value changed to 0.0
Initializing network layer
Network AP/hostname: TEST-Z-WEMOSEM-
Using Supla protocol version 16
Current status: [5] SuplaDevice initialized
Enter normal mode
WiFi: establishing connection with SSID: ""
Connected BSSID: 80:CC:9C:34:BD:AB
local IP: 192.168.0.xxx
subnetMask: 255.255.255.0
gatewayIP: 192.168.0.1
Signal strength (RSSI): -62 dBm
Establishing NOT encrypted connection with: svrxx.supla.org (port: 2015)
Connected to Supla Server
Current status: [10] Register in progress
Device registered (activity timeout 120 s, server version: 19, server min version: 1)
Current status: [17] Registered and ready
Changing activity timeout to 2400
Activity timeout set to 96 s
ESP to Sleep mode
WiFi station disconnected
User avatar
YoMan
Posts: 3522
Joined: Thu Apr 30, 2020 5:18 pm
Location: Częstochowa
Has thanked: 3 times
Been thanked: 3 times

Post

endrju_88 wrote: Tue Apr 25, 2023 6:40 pm A to wyświetla przy suchym czujniku :
Litości dla tego forum. Oznacz kod tagiem żeby nie smiecic.

Code: Select all

takim prosze
YoMan
________________________________________
Wziąłem udział w SOP2023 & SOP2024
endrju_88
Posts: 448
Joined: Tue Apr 25, 2023 1:02 pm
Has thanked: 3 times
Been thanked: 4 times

Post

Ok. Wybacz ;)
endrju_88
Posts: 448
Joined: Tue Apr 25, 2023 1:02 pm
Has thanked: 3 times
Been thanked: 4 times

Post

Ok. oto co pokazało z mokrym czujnikiem :

Code: Select all

ets Jan 8 2013,rst cause:2, boot mode:(3,6)

load 0x4010f000, len 3460, room 16
tail 4
chksum 0xcc
load 0x3fff20b8, len 40, room 4
tail 4
chksum 0xc9
csum 0xc9
v000979f0
~ld
Config read
Key: 0 Value: ⸮⸮ķ⸮⸮7!g`⸮]⸮
Key: 1 Value: ⸮⸮⸮20⸮N79Q⸮⸮⸮⸮:
Key: 2 Value: wifi
Key: 3 Value: ssid
Key: 4 Value: admin
Key: 5 Value: haslo
Key: 6 Value: TEST z WEMOSEM
Key: 7 Value: svrxx.supla.org
Key: 8 Value: email
Key: 9 Value: 0
Key: 10 Value: 0
Key: 11 Value: 1
Key: 12 Value:
Key: 13 Value:
Key: 14 Value:
Key: 15 Value:
Key: 16 Value: 103
Key: 17 Value:
Key: 18 Value:
Key: 19 Value: 1,,,,,,,,,,,1,,,
Key: 20 Value:
Key: 21 Value: 1
Key: 22 Value:
Key: 23 Value:
Key: 24 Value: ,,,,,,,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 25 Value:
Key: 26 Value:
Key: 27 Value:
Key: 28 Value: 1,9,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 29 Value: 1,10,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 30 Value:
Key: 31 Value:
Key: 32 Value:
Key: 33 Value:
Key: 34 Value:
Key: 35 Value:
Key: 36 Value: 1,3,,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 37 Value:
Key: 38 Value:
Key: 39 Value:
Key: 40 Value:
Key: 41 Value:
Key: 42 Value:
Key: 43 Value:
Key: 44 Value:
Key: 45 Value:
Key: 46 Value:
Key: 47 Value:
Key: 48 Value:
Key: 49 Value: 21,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 50 Value: 0,,,,,,,,,,,,,,,,
Key: 51 Value: ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 52 Value: ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 53 Value:
Key: 54 Value:
Key: 55 Value:
Key: 56 Value:
Key: 57 Value:
Key: 58 Value: 1
Key: 59 Value: 0
Key: 60 Value:
Key: 61 Value: 20
Key: 62 Value:
Key: 63 Value:
Key: 64 Value: 0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 65 Value:
Key: 66 Value:
Key: 67 Value:
Key: 68 Value:
Key: 69 Value:
Key: 70 Value:
Key: 71 Value:
Key: 72 Value:
Key: 73 Value:
Key: 74 Value: 0.45
Key: 75 Value: 0.45
Key: 76 Value:
Key: 77 Value:
Key: 78 Value:
Key: 79 Value: 1
Key: 80 Value: 0
Key: 81 Value:
Key: 82 Value:
Key: 83 Value:
Key: 84 Value:
Key: 85 Value:
Key: 86 Value: 0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 87 Value: 0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 88 Value: 0
Key: 89 Value:
Key: 90 Value:
Supla - starting initialization
Storage initialization
readStorage: 8; Read: [53 55 50 4C 41 1 0 0 ]
Storage: Number of sections 0
Config storage not configured
Validating storage state section with current device configuration
Storage state section validation completed. Loading elements state...
Channel(2) value changed to 1008.73
Channel(1) value changed to temp(23.070000), humi(54.695312)
Channel(3) value changed to 0.0
Initializing network layer
Network AP/hostname: TEST-Z-WEMOSEM-
Using Supla protocol version 16
Current status: [5] SuplaDevice initialized
Enter normal mode
WiFi: establishing connection with SSID: ""
Connected BSSID: 80:CC:9C:34:BD:AB
local IP: 192.168.0.xxx
subnetMask: 255.255.255.0
gatewayIP: 192.168.0.1
Signal strength (RSSI): -57 dBm
Establishing NOT encrypted connection with: svrxx.supla.org (port: 2015)
Connected to Supla Server
Current status: [10] Register in progress
Device registered (activity timeout 120 s, server version: 19, server min version: 1)
Current status: [17] Registered and ready
Changing activity timeout to 2400
ESP to Sleep mode
WiFi station disconnected
A to wyświetla przy suchym czujniku :

Code: Select all

ets Jan 8 2013,rst cause:2, boot mode:(3,6)

load 0x4010f000, len 3460, room 16
tail 4
chksum 0xcc
load 0x3fff20b8, len 40, room 4
tail 4
chksum 0xc9
csum 0xc9
v000979f0
~ld
Config read
Key: 0 Value: ⸮⸮ķ⸮⸮7!g`⸮]⸮
Key: 1 Value: ⸮⸮⸮20⸮N79Q⸮⸮⸮⸮:
Key: 2 Value: wifi
Key: 3 Value: ssid
Key: 4 Value: admin
Key: 5 Value: haslo
Key: 6 Value: TEST z WEMOSEM
Key: 7 Value: svrxx.supla.org
Key: 8 Value: email
Key: 9 Value: 0
Key: 10 Value: 0
Key: 11 Value: 1
Key: 12 Value:
Key: 13 Value:
Key: 14 Value:
Key: 15 Value:
Key: 16 Value: 103
Key: 17 Value:
Key: 18 Value:
Key: 19 Value: 1,,,,,,,,,,,1,,,
Key: 20 Value:
Key: 21 Value: 1
Key: 22 Value:
Key: 23 Value:
Key: 24 Value: ,,,,,,,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 25 Value:
Key: 26 Value:
Key: 27 Value:
Key: 28 Value: 1,9,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 29 Value: 1,10,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 30 Value:
Key: 31 Value:
Key: 32 Value:
Key: 33 Value:
Key: 34 Value:
Key: 35 Value:
Key: 36 Value: 1,3,,1,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 37 Value:
Key: 38 Value:
Key: 39 Value:
Key: 40 Value:
Key: 41 Value:
Key: 42 Value:
Key: 43 Value:
Key: 44 Value:
Key: 45 Value:
Key: 46 Value:
Key: 47 Value:
Key: 48 Value:
Key: 49 Value: 21,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 50 Value: 0,,,,,,,,,,,,,,,,
Key: 51 Value: ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 52 Value: ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 53 Value:
Key: 54 Value:
Key: 55 Value:
Key: 56 Value:
Key: 57 Value:
Key: 58 Value: 1
Key: 59 Value: 0
Key: 60 Value:
Key: 61 Value: 20
Key: 62 Value:
Key: 63 Value:
Key: 64 Value: 0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 65 Value:
Key: 66 Value:
Key: 67 Value:
Key: 68 Value:
Key: 69 Value:
Key: 70 Value:
Key: 71 Value:
Key: 72 Value:
Key: 73 Value:
Key: 74 Value: 0.45
Key: 75 Value: 0.45
Key: 76 Value:
Key: 77 Value:
Key: 78 Value:
Key: 79 Value: 1
Key: 80 Value: 0
Key: 81 Value:
Key: 82 Value:
Key: 83 Value:
Key: 84 Value:
Key: 85 Value:
Key: 86 Value: 0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 87 Value: 0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 88 Value: 0
Key: 89 Value:
Key: 90 Value:
Supla - starting initialization
Storage initialization
readStorage: 8; Read: [53 55 50 4C 41 1 0 0 ]
Storage: Number of sections 0
Config storage not configured
Validating storage state section with current device configuration
Storage state section validation completed. Loading elements state...
Channel(0) value changed to 1
Channel(2) value changed to 1008.71
Channel(1) value changed to temp(23.170000), humi(56.889648)
Channel(3) value changed to 0.0
Initializing network layer
Network AP/hostname: TEST-Z-WEMOSEM-
Using Supla protocol version 16
Current status: [5] SuplaDevice initialized
Enter normal mode
WiFi: establishing connection with SSID: ""
Connected BSSID: 80:CC:9C:34:BD:AB
local IP: 192.168.0.xxx
subnetMask: 255.255.255.0
gatewayIP: 192.168.0.1
Signal strength (RSSI): -62 dBm
Establishing NOT encrypted connection with: svrxx.supla.org (port: 2015)
Connected to Supla Server
Current status: [10] Register in progress
Device registered (activity timeout 120 s, server version: 19, server min version: 1)
Current status: [17] Registered and ready
Changing activity timeout to 2400
Activity timeout set to 96 s
ESP to Sleep mode
WiFi station disconnected

Wybaczcie za zaśmiecanie , ale jestem nowy na forum.

Return to “Pomoc”