Problem GG na ESP12, ESP07S, Wemos

[mareks6]

Zakładam nowy temat gdyz nie znalazłem nigdzie odpowiedzi. Jeśli zły dział to przepraszam.

Buduję dość skomplikowany układ - 2 PCB na kanapkę do obudowy 4-modułowej na szynę DIN. Wygenerowałem na stronie buildera GG z potrzebnymi mi opcjami (widoczne na fotkach) i mam problem. Gdy tylko podam dane na pierwszej stronie oraz przypiszę chociażby jedną rzecz (przekaźnik, PCF8574, itp) to po ponownym uruchomieniu moduł pojawi mi się na koncie supla lecz średnio co 5 sekund się zawiesza i restartuje.

Nawet jeśli uda mi się uruchomić menu konfiguracyjne (szybkie miganie LED) to po połączeniu z nadawana siecią WiFi, nie mogę się zalogować na moduł - przeglądarka wywala błąd "Przekroczono limit czasu połączenia", a po chwili widzę jak moduł się znów sam zresetował. Czyli te zawiechy i restarty następują zarówno podczas normalnego działania, jak i podczas przejścia modułu w tryb config.


Poza swoim modułem (z ESP-12F oraz po wymianie, z ESP-07S) testowałem firmware na wemos mini oraz tym większym - dzieje się to samo lecz te gotowce odrobinę szybciej wstają. Z początku generowałem firmware z ustawieniem pamięci na 1MB, dopiero później próbowałem z widocznym na fotkach ustawieniem 4MB. Oczywiście to samo ustawiałem w programie do wgrywania wsadu.

Czy ESP może mieć za mało podręcznej pamięci by to obsłużyć i stąd zwiechy i restart? Nie wiem o co chodzi z tą pamięcią podczas konfigurowania wszystkiego na module, ale jak wszystko ustawiłem to wyświetlało mi tam, że pozostało ok 18kB pamięci.

Wgrałem jakąś starą kompilację GG, która obsługiwała tylko przekaźniki i działa normalnie i mogę też bez problemu wejść ponownie do menu config.

Tak więc wina leży gdzieś po stronie GG lub ograniczeń ESP...


----------------EDIT---------------

ZDECYDOWANIE wina leży po stronie samego GG. Udało mi się znaleźć na komputerze kompilacje GG z sierpnia tego roku, kiedy to przed projektowaniem PCB wszystko sprawdzałem na pająka i gotowych modułach. Wtedy wszystko mi działało i teraz na moim gotowym module ta kompilacja też bezbłędnie działa.

Tak więc proszę o uwagę osób, które od tego czasu coś zmieniały (a pewnie troszkę tego było) w Generic GUI.
W razie czego, zanim modułu nie mam zamontowanego to mogę potestować jakieś poprawki GG

[klew]

Zacznij od sprawdzenia logów z urządzenia

[mareks6]

Zacznij od sprawdzenia logów z urządzenia

Właśnie próbowałem się połączyć przez putty z modułem, po adresie IP na jakim się zgłosił w routerze lecz bez powodzenia.

Rozumiem, że jeśli w configu ustawiłem linie RX i TX pod czujniki DS oraz DHT to tymi liniami nie mogę już się wpiąć przejściówką żeby putty poprzez RS połączyć?

[klew]

Zacznij od sprawdzenia logów z urządzenia

Właśnie próbowałem się połączyć przez putty z modułem, po adresie IP na jakim się zgłosił w routerze lecz bez powodzenia.

Rozumiem, że jeśli w configu ustawiłem linie RX i TX pod czujniki DS oraz DHT to tymi liniami nie mogę już się wpiąć przejściówką żeby putty poprzez RS połączyć?

Urządzenie nie wysyła logów po sieci. Tylko przez programator. Jak coś tam ustawiasz, to logowanie może nie działać.
Spróbuj wyrzucić na chwilę DS i DHT i zobacz, czy moduł nadal się dziwnie zachowuje i wtedy sprawdź logi.
Oczywiście nie rób tego pod zasilaniem sieciowym.

[mareks6]

Ok, urządzenie jest co prawda na szynę DIN ale na napięcie 12V (obok mam zasilacz na szynie), także myślę że spokojnie mogę testy robić na tym zewnętrznym zasilaniu, podłączając z programatora jedynie GND, RX oraz TX.

Teraz jestem poza domem ale jak tylko będę na miejscu to wgram do modułu ponownie wygenerowane wczoraj firmware i sprawdzę co pokazuje.

Możesz na szybko jeszcze napisać jak mam ustawić putty - prędkość itp - nie wiem czy to takie same parametry jak ogólnodostępne w internecie czy pod firmware supli muszę inaczej ustawiać

[klew]

Ok, urządzenie jest co prawda na szynę DIN ale na napięcie 12V (obok mam zasilacz na szynie), także myślę że spokojnie mogę testy robić na tym zewnętrznym zasilaniu, podłączając z programatora jedynie GND, RX oraz TX.

Teraz jestem poza domem ale jak tylko będę na miejscu to wgram do modułu ponownie wygenerowane wczoraj firmware i sprawdzę co pokazuje.

Możesz na szybko jeszcze napisać jak mam ustawić putty - prędkość itp - nie wiem czy to takie same parametry jak ogólnodostępne w internecie czy pod firmware supli muszę inaczej ustawiać

Raczej standardowe. Nie wiem jaki baud jest ustawiony w GG, ale albo ten 74xxx albo 115xxx.
Spróbuj oba i zobacz, gdzie będą sensowne rzeczy.
Odnośnie podłączania się pod urządzenie pracujące na 12 V, to się nie wypowiem. Nie mam pojęcia czy to jest bezpieczne dla prorgamatora i komputera.

[mareks6]

Wina leży chyba w czymś po stronie 1Wire. Wgrałem znów ten problematyczny wsad z przedwczoraj i dopóki nie skonfigurowałem 1Wire na liniach RX/TX to wszystko działało normalnie. I normalnie mogłem ponownie wejść w config. Kiedy już tam wszedłem, to skonfigurowałem na początek tylko czujnik DS18B20 na lini RX. Linię TX zostawiłem bez zmian z myślą, że może programator będzie mógł nadal z niej pobierać dane i w putty coś zobaczę.

I tu od razu po zapisaniu tych ustawień i restarcie modułu zaczęło się to samo - moduł się łączy z cloud, a po kilku sekundach zwiecha i restart. Co ciekawe - gdy podłączyłem czujnik DS do linii RX na której go skonfigurowałem, to problem ustał i znów jestem w stanie wejść w config, gdyż moduł się nie zwiesza i nie restartuje. Tak więc dzieje się to tylko gdy zadeklaruję na jakimś GPIO czujnik na 1Wire i niczego tam nie podłączę. Tego nie było w sierpniowym wsadzie kiedy go generowałem - mogłem ustawić czujniki DS i DHT na liniach RX / TX i ich od razu nie podłączać, a wszystko działało normalnie.

Logi w kolejnym poście

[mareks6]

Pełne logi od momentu wielokrotnie powtarzane kominikatu o restarcie 1Wire do kolejnych takich komunikatów (po przypisaniu RX do DSa w configu):

Code: Select all

Restarting OneWire...
Restarting OneWire...
Restarting OneWire...
Restarting OneWire...

User exception (panic/abort/assert)
                                   --------------- CUT HERE FOR EXCEPTION DECODER ---------------

Panic core_esp8266_main.cpp:191 __yield

>>>stack>>>

ctx: sys
sp: 3ffff180 end: 3fffffb0 offset: 0010
3ffff190:  000002ed 3fff1a78 4023625a 4023627d
3ffff1a0:  000002ed 00012b2f 3fff0600 4022e501
3ffff1b0:  00000000 00012b2f 3fff0600 4022e57c
3ffff1c0:  3fff5d64 3ffe83c4 3fff404d 3fff404c
3ffff1d0:  40100384 3fff0600 3fff0600 40219a08
3ffff1e0:  3fff404e 3fff404c 3fff0600 3fff1a78
3ffff1f0:  00000000 3fff0600 3fff338c 40219a9e
3ffff200:  00000000 3fff0600 3fff338c 40219b5a
3ffff210:  00000000 c05fc000 3fff0600 3fff1a78
3ffff220:  00000000 3fff0600 3fff338c 40219aa8
3ffff230:  00000000 3fff0600 3fff338c 40219b5a
3ffff240:  00000000 c05fc000 3fff0600 3fff1a78
3ffff250:  00000000 3fff0600 3fff338c 40219aa8
3ffff260:  00000000 3fff0600 3fff338c 40219b5a
3ffff270:  00000000 c05fc000 3fff0600 3fff1a78
3ffff280:  00000000 3fff0600 3fff338c 40219aa8
3ffff290:  00000000 3fff0600 3fff338c 40219b5a
3ffff2a0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff2b0:  00000000 3fff0600 3fff338c 40219aa8
3ffff2c0:  00000000 3fff0600 3fff338c 40219b5a
3ffff2d0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff2e0:  00000000 3fff0600 3fff338c 40219aa8
3ffff2f0:  00000000 3fff0600 3fff338c 40219b5a
3ffff300:  00000000 c05fc000 3fff0600 3fff1a78
3ffff310:  00000000 3fff0600 3fff338c 40219aa8
3ffff320:  00000000 3fff0600 3fff338c 40219b5a
3ffff330:  00000000 c05fc000 3fff0600 3fff1a78
3ffff340:  00000000 3fff0600 3fff338c 40219aa8
3ffff350:  00000000 3fff0600 3fff338c 40219b5a
3ffff360:  00000000 c05fc000 3fff0600 3fff1a78
3ffff370:  00000000 3fff0600 3fff338c 40219aa8
3ffff380:  00000000 3fff0600 3fff338c 40219b5a
3ffff390:  00000000 c05fc000 3fff0600 3fff1a78
3ffff3a0:  00000000 3fff0600 3fff338c 40219aa8
3ffff3b0:  00000000 3fff0600 3fff338c 40219b5a
3ffff3c0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff3d0:  00000000 3fff0600 3fff338c 40219aa8
3ffff3e0:  00000000 3fff0600 3fff338c 40219b5a
3ffff3f0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff400:  00000000 3fff0600 3fff338c 40219aa8
3ffff410:  00000000 3fff0600 3fff338c 40219b5a
3ffff420:  00000000 c05fc000 3fff0600 3fff1a78
3ffff430:  00000000 3fff0600 3fff338c 40219aa8
3ffff440:  00000000 3fff0600 3fff338c 40219b5a
3ffff450:  00000000 c05fc000 3fff0600 3fff1a78
3ffff460:  00000000 3fff0600 3fff338c 40219aa8
3ffff470:  00000000 3fff0600 3fff338c 40219b5a
3ffff480:  00000000 c05fc000 3fff0600 3fff1a78
3ffff490:  00000000 3fff0600 3fff338c 40219aa8
3ffff4a0:  00000000 3fff0600 3fff338c 40219b5a
3ffff4b0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff4c0:  00000000 3fff0600 3fff338c 40219aa8
3ffff4d0:  00000000 3fff0600 3fff338c 40219b5a
3ffff4e0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff4f0:  00000000 3fff0600 3fff338c 40219aa8
3ffff500:  00000000 3fff0600 3fff338c 40219b5a
3ffff510:  00000000 c05fc000 3fff0600 3fff1a78
3ffff520:  00000000 3fff0600 3fff338c 40219aa8
3ffff530:  00000000 3fff0600 3fff338c 40219b5a
3ffff540:  00000000 c05fc000 3fff0600 3fff1a78
3ffff550:  00000000 3fff0600 3fff338c 40219aa8
3ffff560:  00000000 3fff0600 3fff338c 40219b5a
3ffff570:  00000000 c05fc000 3fff0600 3fff1a78
3ffff580:  00000000 3fff0600 3fff338c 40219aa8
3ffff590:  00000000 3fff0600 3fff338c 40219b5a
3ffff5a0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff5b0:  00000000 3fff0600 3fff338c 40219aa8
3ffff5c0:  00000000 3fff0600 3fff338c 40219b5a
3ffff5d0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff5e0:  00000000 3fff0600 3fff338c 40219aa8
3ffff5f0:  00000000 3fff0600 3fff338c 40219b5a
3ffff600:  00000000 c05fc000 3fff0600 3fff1a78
3ffff610:  00000000 3fff0600 3fff338c 40219aa8
3ffff620:  00000000 3fff0600 3fff338c 40219b5a
3ffff630:  00000000 c05fc000 3fff0600 3fff1a78
3ffff640:  00000000 3fff0600 3fff338c 40219aa8
3ffff650:  00000000 3fff0600 3fff338c 40219b5a
3ffff660:  00000000 c05fc000 3fff0600 3fff1a78
3ffff670:  00000000 3fff0600 3fff338c 40219aa8
3ffff680:  00000000 3fff0600 3fff338c 40219b5a
3ffff690:  00000000 c05fc000 3fff0600 3fff1a78
3ffff6a0:  00000000 3fff0600 3fff338c 40219aa8
3ffff6b0:  00000000 3fff0600 3fff338c 40219b5a
3ffff6c0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff6d0:  00000000 3fff0600 3fff338c 40219aa8
3ffff6e0:  00000000 3fff0600 3fff338c 40219b5a
3ffff6f0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff700:  00000000 3fff0600 3fff338c 40219aa8
3ffff710:  00000000 3fff0600 3fff338c 40219b5a
3ffff720:  00000000 c05fc000 3fff0600 3fff1a78
3ffff730:  00000000 3fff0600 3fff338c 40219aa8
3ffff740:  00000000 3fff0600 3fff338c 40219b5a
3ffff750:  00000000 c05fc000 3fff0600 3fff1a78
3ffff760:  00000000 3fff0600 3fff338c 40219aa8
3ffff770:  00000000 3fff0600 3fff338c 40219b5a
3ffff780:  00000000 c05fc000 3fff0600 3fff1a78
3ffff790:  00000000 3fff0600 3fff338c 40219aa8
3ffff7a0:  00000000 3fff0600 3fff338c 40219b5a
3ffff7b0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff7c0:  00000000 3fff0600 3fff338c 40219aa8
3ffff7d0:  00000000 3fff0600 3fff338c 40219b5a
3ffff7e0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff7f0:  00000000 3fff0600 3fff338c 40219aa8
3ffff800:  00000000 3fff0600 3fff338c 40219b5a
3ffff810:  00000000 c05fc000 3fff0600 3fff1a78
3ffff820:  00000000 3fff0600 3fff338c 40219aa8
3ffff830:  00000000 3fff0600 3fff338c 40219b5a
3ffff840:  00000000 c05fc000 3fff0600 3fff1a78
3ffff850:  00000000 3fff0600 3fff338c 40219aa8
3ffff860:  00000000 3fff0600 3fff338c 40219b5a
3ffff870:  00000000 c05fc000 3fff0600 3fff1a78
3ffff880:  00000000 3fff0600 3fff338c 40219aa8
3ffff890:  00000000 3fff0600 3fff338c 40219b5a
3ffff8a0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff8b0:  00000000 3fff0600 3fff338c 40219aa8
3ffff8c0:  00000000 3fff0600 3fff338c 40219b5a
3ffff8d0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff8e0:  00000000 3fff0600 3fff338c 40219aa8
3ffff8f0:  00000000 3fff0600 3fff338c 40219b5a
3ffff900:  00000000 c05fc000 3fff0600 3fff1a78
3ffff910:  00000000 3fff0600 3fff338c 40219aa8
3ffff920:  00000000 3fff0600 3fff338c 40219b5a
3ffff930:  00000000 c05fc000 3fff0600 3fff1a78
3ffff940:  00000000 3fff0600 3fff338c 40219aa8
3ffff950:  00000000 3fff0600 3fff338c 40219b5a
3ffff960:  00000000 c05fc000 3fff0600 3fff1a78
3ffff970:  00000000 3fff0600 3fff338c 40219aa8
3ffff980:  00000000 3fff0600 3fff338c 40219b5a
3ffff990:  00000000 c05fc000 3fff0600 3fff1a78
3ffff9a0:  00000000 3fff0600 3fff338c 40219aa8
3ffff9b0:  00000000 3fff0600 3fff338c 40219b5a
3ffff9c0:  00000000 c05fc000 3fff0600 3fff1a78
3ffff9d0:  00000000 3fff0600 3fff338c 40219aa8
3ffff9e0:  00000000 3fff0600 3fff338c 40219b5a
3ffff9f0:  00000000 c05fc000 3fff0600 3fff1a78
3ffffa00:  00000000 3fff0600 3fff338c 40219aa8
3ffffa10:  00000000 3fff0600 3fff338c 40219b5a
3ffffa20:  00000000 c05fc000 3fff0600 3fff1a78
3ffffa30:  00000000 3fff0600 3fff338c 40219aa8
3ffffa40:  00000000 3fff0600 3fff338c 40219b5a
3ffffa50:  00000000 c05fc000 3fff0600 3fff1a78
3ffffa60:  00000000 3fff0600 3fff338c 40219aa8
3ffffa70:  00000000 3fff0600 3fff338c 40219b5a
3ffffa80:  00000000 c05fc000 3fff0600 3fff1a78
3ffffa90:  00000000 3fff0600 3fff338c 40219aa8
3ffffaa0:  00000000 3fff0600 3fff338c 40219b5a
3ffffab0:  00000000 c05fc000 3fff0600 3fff1a78
3ffffac0:  00000000 3fff0600 3fff338c 40219aa8
3ffffad0:  00000000 3fff0600 3fff338c 40219b5a
3ffffae0:  00000000 c05fc000 3fff0600 3fff1a78
3ffffaf0:  00000000 3fff0600 3fff338c 40219aa8
3ffffb00:  00000000 3fff0600 3fff338c 40219b5a
3ffffb10:  00000000 c05fc000 3fff0600 3fff1a78
3ffffb20:  00000000 3fff0600 3fff338c 40219aa8
3ffffb30:  00000000 3fff0600 3fff338c 40219b5a
3ffffb40:  00000000 c05fc000 3fff0600 3fff1a78
3ffffb50:  00000000 3fff0600 3fff338c 40219aa8
3ffffb60:  00000000 3fff0600 3fff338c 40219b5a
3ffffb70:  00000000 c05fc000 3fff0600 3fff1a78
3ffffb80:  00000000 3fff0600 3fff338c 40219aa8
3ffffb90:  00000000 3fff0600 3fff338c 40219b5a
3ffffba0:  00000000 c05fc000 3fff0600 3fff1a78
3ffffbb0:  00000000 3fff0600 3fff338c 40219aa8
3ffffbc0:  00000000 3fff0600 3fff338c 40219b5a
3ffffbd0:  00000000 c05fc000 3fff0600 3fff1a78
3ffffbe0:  00000000 3fff0600 3fff338c 40219aa8
3ffffbf0:  00000000 3fff0600 3fff338c 40219b5a
3ffffc00:  00000000 c05fc000 3fff0600 3fff1a78
3ffffc10:  00000000 3fff0600 3fff338c 40219aa8
3ffffc20:  00000000 3fff0600 3fff338c 40219b5a
3ffffc30:  00000000 c05fc000 3fff0600 3fff1a78
3ffffc40:  00000000 3fff0600 3fff338c 40219aa8
3ffffc50:  00000000 3fff0600 3fff338c 40219b5a
3ffffc60:  00000000 c05fc000 3fff0600 3fff1a78
3ffffc70:  00000000 3fff0600 3fff338c 40219aa8
3ffffc80:  00000000 3fff0600 3fff338c 40219b5a
3ffffc90:  00000000 c05fc000 3fff0600 3fff1a78
3ffffca0:  00000000 3fff0600 3fff338c 40219aa8
3ffffcb0:  00000000 3fff0600 3fff338c 40219b5a
3ffffcc0:  00000000 c05fc000 3fff0600 3fff1a78
3ffffcd0:  00000000 3fff0600 3fff338c 40219aa8
3ffffce0:  00000000 3fff0600 3fff338c 40219b5a
3ffffcf0:  00000000 c05fc000 3fff0600 3fff1a78
3ffffd00:  00000000 3fff0600 3fff338c 40219aa8
3ffffd10:  00000000 3fff0600 3fff338c 40219b5a
3ffffd20:  00000000 c05fc000 3fff0600 3fff1a78
3ffffd30:  00000000 3fff0600 3fff338c 40219aa8
3ffffd40:  00000000 3fff0600 3fff338c 40219b5a
3ffffd50:  00000000 c05fc000 3fff0600 3fff1a78
3ffffd60:  00000000 3fff0600 3fff338c 40219aa8
3ffffd70:  00000000 3fff0600 3fff338c 40219b5a
3ffffd80:  00000000 c05fc000 3fff0600 3fff1a78
3ffffd90:  00000000 3fff0600 3fff338c 40219aa8
3ffffda0:  00000000 3fff0600 3fff338c 40219b5a
3ffffdb0:  00000000 c05fc000 3fff0600 3fff1a78
3ffffdc0:  00000000 3fff0600 3fff338c 40219aa8
3ffffdd0:  00000000 3fff0600 3fff338c 40219b5a
3ffffde0:  00000000 c05fc000 3fff0600 3fff1a78
3ffffdf0:  00000000 3fff0600 3fff338c 40219aa8
3ffffe00:  00000000 3fff0600 3fff338c 40219b5a
3ffffe10:  00000000 c05fc000 3fff0600 3fff1a78
3ffffe20:  00000000 3fff0600 3fff338c 40219aa8
3ffffe30:  00000000 3fff0600 3fff338c 40219b5a
3ffffe40:  00000000 c05fc000 3fff0600 3fff1a78
3ffffe50:  00000000 3fff0600 3fff338c 40219aa8
3ffffe60:  00000000 3fff0600 3fff338c 40219b5a
3ffffe70:  00000000 c05fc000 7eb851eb 3fff1a78
3ffffe80:  3fff05fc 00006493 3fff338c 40219997
3ffffe90:  00006493 00006493 00000000 402372fc
3ffffea0:  00006493 3fff0664 3fff338c 4021c792
3ffffeb0:  3fffdad0 00006493 3fff0664 4021d21a
3ffffec0:  3fff04f8 3fffdad0 3fff1a78 00000030
3ffffed0:  3ffffee0 00000008 00000000 00000081
3ffffee0:  3fff22b8 00000005 00000005 3ffe9ef6
3ffffef0:  00000000 00000001 3fff0664 4021c61f
3fffff00:  00000000 00000001 3fff0664 4021d85f
3fffff10:  44354641 39363131 39393538 46454332
3fffff20:  40106705 007a8d5d 3fff1a50 00000000
3fffff30:  3fff0080 3fff1a50 3ffe86c4 3fff1a50
3fffff40:  00000000 00006493 47ae147a 00744a4a
3fffff50:  00006483 3fff1a50 00000010 00000010
3fffff60:  3fffdad0 00000010 00006483 40236331
3fffff70:  00000000 00006483 40c49ba5 007437c2
3fffff80:  00000000 00006493 4b020c49 00744a4e
3fffff90:  3fffdad0 00006483 00000010 3fff1a78
3fffffa0:  3fffdad0 00000000 00006493 40205e48
<<<stack<<<

--------------- CUT HERE FOR EXCEPTION DECODER ---------------
                                                              ▒▒*▒P*V▒▒ET▒▒▒▒T▒▒+▒▒u▒U+UZ▒▒UT▒▒▒TQT▒UQ▒▒jP▒▒▒▒u▒▒▒▒▒ZT▒(E▒▒▒▒Q▒UEu▒▒▒▒*▒▒▒jPE*▒u▒▒E+▒▒TT)UZV▒▒▒(ZV▒▒▒▒(QT▒▒▒▒*U▒rf cal sector: 252
freq trace enable 0
rf[112] : 00▒Config read
Key: 0 Value: ▒]i▒▒,▒t▒Ң▒▒O
Key: 1 Value: ▒ly▒yQ▒U
                      ۚE▒▒w
Key: 2 Value: SmartHouse
Key: 3 Value: pass
Key: 4 Value: admin
Key: 5 Value: pass
Key: 6 Value: GUI Generic - test
Key: 7 Value: svr11.supla.org
Key: 8 Value: mail
Key: 9 Value: 4
Key: 10 Value: 4
Key: 11 Value: 4
Key: 12 Value: 1
Key: 13 Value:
Key: 14 Value: 1
Key: 15 Value:
Key: 16 Value:
Key: 17 Value:
Key: 18 Value:
Key: 19 Value:
Key: 20 Value:
Key: 21 Value: 1
Key: 22 Value:
Key: 23 Value:
Key: 24 Value: ,,0,1,0,2,0,1,,,,,0,2,,,1,,,,,,,,,,,
Key: 25 Value: ,,0,1,0,2,0,,,,,,1,2,,,1,,,,,,,,,,,,
Key: 26 Value: ,,1,1,0,2,0,,,,,,2,2,,,1,1,,,,,,,,,,
Key: 27 Value: 1,6,0,1,0,2,0,,,,,,3,2,,,1,,,,,,,,,,
Key: 28 Value: 1,10,0,0,0,0,0,,,,,,0,3,,,0,,,,,,,,,
Key: 29 Value: 1,9,0,0,0,0,0,,,,,,1,3,,,0,,,,,,,,,,
Key: 30 Value: ,,0,0,0,0,0,,,,,,2,3,,,0,,,,,,,,,,,,
Key: 31 Value: ,,0,0,0,0,0,,,,,,3,3,,,0,,,,,,,,,,,,
Key: 32 Value:
Key: 33 Value:
Key: 34 Value:
Key: 35 Value:
Key: 36 Value: 1,1,1,,0,,0,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 37 Value: 2,1,1,,0,,0,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 38 Value: 3,1,1,,0,,0,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 39 Value: 1,25,,,0,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 40 Value: 4,1,1,,0,,0,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 41 Value: ,,,0,,2,0,,,,,,,,,,1,,,,,,,,,,,,,,,,
Key: 42 Value:
Key: 43 Value:
Key: 44 Value:
Key: 45 Value: 1
Key: 46 Value:
Key: 47 Value:
Key: 48 Value:
Key: 49 Value:
Key: 50 Value:
Key: 51 Value:
Key: 52 Value:
Key: 53 Value:
Key: 54 Value:
Key: 55 Value:
Key: 56 Value:
Key: 57 Value:
Key: 58 Value: 1
Key: 59 Value: 0
Key: 60 Value:
Key: 61 Value:
Key: 62 Value:
Key: 63 Value:
Key: 64 Value:
Key: 65 Value:
Key: 66 Value:
Key: 67 Value:
Key: 68 Value:
Key: 69 Value:
Key: 70 Value:
Key: 71 Value:
Key: 72 Value:
Key: 73 Value:
Key: 74 Value: 0.25
Key: 75 Value: 0.4
Key: 76 Value:
Key: 77 Value:
Key: 78 Value:
Key: 79 Value:
Key: 80 Value: 0
Key: 81 Value: ,0,3,3,0,0,0,,0,0,0,
Key: 82 Value:
Key: 83 Value:
Key: 84 Value:
Key: 85 Value:
Key: 86 Value:
Key: 87 Value:
Key: 88 Value:
Key: 89 Value: 1,0,2,3,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 90 Value: ,,,,,,,0,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 91 Value:
Key: 92 Value:
Key: 93 Value:
Key: 94 Value:
Key: 95 Value:
Key: 96 Value:
Key: 97 Value:
Key: 98 Value:
PCF8574 is connected address: 22
Button[0]::setMulticlickTime: 250
Button[0]::setHoldTime: 400
Button[1]::setMulticlickTime: 250
Button[1]::setHoldTime: 400
Button[2]::setMulticlickTime: 250
Button[2]::setHoldTime: 400
Button[3]::setMulticlickTime: 250
Button[3]::setHoldTime: 400
Button[4]::setMulticlickTime: 450
Button[4]::setHoldTime: 5000
Channel(8) value changed to -275.0
Button[5]::setMulticlickTime: 200
Button[5]::setHoldTime: 400
Supla - starting initialization
Storage initialization
readStorage: 8; Read: [53 55 50 4C 41 1 0 1 ]
Storage: Number of sections 1
Reading section: 0
readStorage: 7; Read: [3 16 0 5A E0 5A E0 ]
Section type: 3; size: 22
CRC1 57434, CRC2 57434, CRC calc 57434
Button[0]::onLoadConfig: skip
Button[1]::onLoadConfig: skip
Button[2]::onLoadConfig: skip
Button[3]::onLoadConfig: skip
Channel function missing. Using SW defaults
Binary[4] setServerInvertLogic 0
Binary[4] config serverInvertLogic 0
Channel function missing. Using SW defaults
Binary[5] setServerInvertLogic 0
Binary[5] config serverInvertLogic 0
Channel function missing. Using SW defaults
Binary[6] setServerInvertLogic 0
Binary[6] config serverInvertLogic 0
Channel function missing. Using SW defaults
Binary[7] setServerInvertLogic 0
Binary[7] config serverInvertLogic 0
Button[4] enabling IN as config button
Channel[8] temperature correction 0.000000
Channel[8] humidity correction 0.000000
RGBWBase[9] button control type: 0
Button[5]::onLoadConfig: skip
Validating storage state section with current device configuration
Storage state section validation completed. Loading elements state...
readStorage: 4; Read: [0 0 0 0 ]
readStorage: 1; Read: [0 ]
readStorage: 4; Read: [0 0 0 0 ]
readStorage: 1; Read: [0 ]
readStorage: 4; Read: [0 0 0 0 ]
readStorage: 1; Read: [0 ]
readStorage: 4; Read: [0 0 0 0 ]
readStorage: 1; Read: [0 ]
readStorage: 1; Read: [0 ]
readStorage: 1; Read: [64 ]
Relay[0] turn OFF (duration 0 ms)
 **** Digital write[0], gpio: 12; value 0
Relay[0] turn OFF (duration 0 ms)
 **** Digital write[0], gpio: 12; value 0
Pin 1, pullUp 1, invertLogic 1, state 1
Relay[1] turn OFF (duration 0 ms)
 **** Digital write[1], gpio: 13; value 0
Relay[1] turn OFF (duration 0 ms)
 **** Digital write[1], gpio: 13; value 0
Pin 0, pullUp 1, invertLogic 1, state 1
Relay[2] turn OFF (duration 0 ms)
 **** Digital write[2], gpio: 14; value 0
Relay[2] turn OFF (duration 0 ms)
 **** Digital write[2], gpio: 14; value 0
Pin 2, pullUp 1, invertLogic 1, state 1
Relay[3] turn OFF (duration 0 ms)
 **** Digital write[3], gpio: 16; value 0
Relay[3] turn OFF (duration 0 ms)
 **** Digital write[3], gpio: 16; value 0
Pin 3, pullUp 1, invertLogic 1, state 1
Channel(4) value changed to 1
Channel(5) value changed to 1
Channel(6) value changed to 1
Channel(7) value changed to 1
Pin 0, pullUp 1, invertLogic 1, state 1
RGBWBase[9] TURN off onInit
RGBW: 0,0,0,0,0
Pin 0, pullUp 1, invertLogic 1, state 1
GUID: AF5D116985992CEFBF74E8D2A284904F
Device name: GUI Generic - test
Device software version: **** Analog write[-1], gpio: 15; value 0
 GG v7.8.14
Initializing network layer
Network AP/hostname: GUI-GENERIC---TEST-840D8E82F8B8
Using Supla protocol version 21
Current status: [5] SuplaDevice initialized
Enter normal mode
WiFi: establishing connection with SSID: "SmartHouse"
Connected BSSID: C6:C9:E3:0C:6B:48
local IP: 192.168.1.187
subnetMask: 255.255.255.0
gatewayIP: 192.168.1.3
Signal strength (RSSI): -53 dBm
Establishing NOT encrypted connection with: svr11.supla.org (port: 2015)
Connected to Supla Server
Initializing SRPC
LAST STATE ADDED: Register in progress
Current status: [10] Register in progress
CH #0, type: 2900, FuncList: 0xEF, default: 130, flags: 0x1010000, value: [00 00 00 00 00 00 00 00]
CH #1, type: 2900, FuncList: 0xEF, default: 130, flags: 0x1010000, value: [00 00 00 00 00 00 00 00]
CH #2, type: 2900, FuncList: 0xEF, default: 130, flags: 0x1010000, value: [00 00 00 00 00 00 00 00]
CH #3, type: 2900, FuncList: 0xEF, default: 130, flags: 0x1010000, value: [00 00 00 00 00 00 00 00]
CH #4, type: 1000, FuncList: 0x0, default: 0, flags: 0x8010000, value: [01 00 00 00 00 00 00 00]
CH #5, type: 1000, FuncList: 0x0, default: 0, flags: 0x8010000, value: [01 00 00 00 00 00 00 00]
CH #6, type: 1000, FuncList: 0x0, default: 0, flags: 0x8010000, value: [01 00 00 00 00 00 00 00]
CH #7, type: 1000, FuncList: 0x0, default: 0, flags: 0x8010000, value: [01 00 00 00 00 00 00 00]
CH #8, type: 3034, FuncList: 0x0, default: 40, flags: 0x8010000, value: [00 00 00 00 00 30 71 c0]
CH #9, type: 4000, FuncList: 0x0, default: 180, flags: 0x10100, value: [00 00 00 00 00 00 00 00]
Send: [53 55 50 4C 41 15 01 00 00 00 45 00 00 00 42 03 00 00 73 77 69 74 61 6C 61 6D 61 72 65 6B 40 69 6E 74 65 72 69 61 2E 70 6C 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 AB 6C 79 9D 79 51 C2 55 0A DB 9A 45 A6 F6 86 77 AF 5D 11 69 85 99 2C EF BF 74 E8 D2 A2 84 90 4F 47 55 49 20 47 65 6E 65 72 69 63 20 2D 20 74 65 73 74 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 01 00 00 00 46 00 00 00 07 00 00 00 03 00 00 00 78 15 01 53 55 50 4C 41 ]
Device registered (activity timeout 120 s, server version: 21, server min version: 1)
LAST STATE ADDED: Registered and ready
Current status: [17] Registered and ready
Changing activity timeout to 30
Send: [53 55 50 4C 41 15 02 00 00 00 D2 00 00 00 01 00 00 00 1E ]
Send: [53 55 50 4C 41 ]
Relay[0]: updating timer value: remainingTime=0 state=0
SRPC sedning: remaining time 0, channel 0, state 0
Send: [53 55 50 4C 41 15 03 00 00 00 69 00 00 00 E3 00 00 00 00 32 DD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 04 00 00 00 A8 02 00 00 06 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 02 00 00 00 AD 02 00 00 1B 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 53 55 50 4C 41 53 55 50 4C 41 15 03 00 00 00 AB 02 00 00 01 00 00 00 04 53 55 50 4C 41 53 55 50 4C 41 15 04 00 00 00 AB 02 00 00 01 00 00 00 05 53 55 50 4C 41 53 55 50 4C 41 15 05 00 00 00 AB 02 00 00 01 00 00 00 06 53 55 50 4C 41 53 55 50 4C 41 15 06 00 00 00 AB 02 00 00 01 00 00 00 07 53 55 50 4C 41 53 55 50 4C 41 15 07 00 00 00 AA 02 00 00 28 00 00 00 08 28 00 00 00 00 20 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 53 55 50 4C 41 53 55 50 4C 41 15 08 00 00 00 AB 02 00 00 01 00 00 00 08 53 55 50 4C 41 53 55 50 4C 41 15 09 00 00 00 DC 00 00 00 03 00 00 00 1E 0A F0 53 55 ]
Received new device config
Sending device config result OK (1)
Send: [53 55 50 4C 41 15 05 00 00 00 B7 02 00 00 0A 00 00 00 01 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Relay[1]: updating timer value: remainingTime=0 state=0
SRPC sedning: remaining time 0, channel 1, state 0
Send: [53 55 50 4C 41 15 06 00 00 00 69 00 00 00 E3 00 00 00 01 32 DD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 07 00 00 00 A8 02 00 00 06 00 00 00 01 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [50 4C 41 53 55 50 4C 41 15 0A 00 00 00 B2 02 00 00 08 00 00 00 00 82 00 00 00 00 00 00 53 55 50 4C 41 ]
Received ChannelConfigFinished for channel 4
Binary[4]: setting default channel config
Binary[4]: processing local channel config
Binary[4] setServerInvertLogic 0
Relay[2]: updating timer value: remainingTime=0 state=0
SRPC sedning: remaining time 0, channel 2, state 0
Send: [53 55 50 4C 41 15 08 00 00 00 69 00 00 00 E3 00 00 00 02 32 DD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 09 00 00 00 A8 02 00 00 06 00 00 00 02 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 0B 00 00 00 B2 02 00 00 08 00 00 00 01 82 00 00 00 00 00 00 53 55 50 4C 41 ]
Received ChannelConfigFinished for channel 5
Binary[5]: setting default channel config
Binary[5]: processing local channel config
Binary[5] setServerInvertLogic 0
Relay[3]: updating timer value: remainingTime=0 state=0
SRPC sedning: remaining time 0, channel 3, state 0
Send: [53 55 50 4C 41 15 0A 00 00 00 69 00 00 00 E3 00 00 00 03 32 DD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 0B 00 00 00 A8 02 00 00 06 00 00 00 03 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 0C 00 00 00 B2 02 00 00 08 00 00 00 02 82 00 00 00 00 00 00 53 55 50 4C 41 ]
Received ChannelConfigFinished for channel 6
Binary[6]: setting default channel config
Binary[6]: processing local channel config
Binary[6] setServerInvertLogic 0
Send: [53 55 50 4C 41 15 0C 00 00 00 67 00 00 00 0E 00 00 00 04 00 00 00 00 00 01 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 0D 00 00 00 A8 02 00 00 06 00 00 00 04 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Received ChannelConfigFinished for channel 7
Binary[7]: setting default channel config
Binary[7]: processing local channel config
Binary[7] setServerInvertLogic 0
Send: [53 55 50 4C 41 15 0E 00 00 00 67 00 00 00 0E 00 00 00 05 00 00 00 00 00 01 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 0F 00 00 00 A8 02 00 00 06 00 00 00 05 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 0D 00 00 00 B2 02 00 00 08 00 00 00 03 82 00 00 00 00 00 00 53 55 50 4C 41 ]
Received SetChannelConfig for channel 8, function 40, config type 0, config size 32
handleChannelConfig, func 40, configtype 0, configsize 32
Channel[8] temperature correction 0.000000
Channel[8] humidity correction 0.000000
Channel[8] config changed offline flag 0
Sending channel config result OK (1)
Send: [53 55 50 4C 41 15 10 00 00 00 B4 02 00 00 03 00 00 00 01 00 08 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 11 00 00 00 67 00 00 00 0E 00 00 00 06 00 00 00 00 00 01 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 12 00 00 00 A8 02 00 00 06 00 00 00 06 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 0E 00 00 00 B2 02 00 00 08 00 00 00 04 00 00 00 00 00 00 00 53 55 50 4C 41 ]
Received ChannelConfigFinished for channel 8
Send: [53 55 50 4C 41 15 13 00 00 00 67 00 00 00 0E 00 00 00 07 00 00 00 00 00 01 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 14 00 00 00 A8 02 00 00 06 00 00 00 07 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 0F 00 00 00 B2 02 00 00 08 00 00 00 05 00 00 00 00 00 00 00 53 55 50 4C 41 ]
Activity timeout set to 30 s
Send: [53 55 50 4C 41 15 15 00 00 00 67 00 00 00 0E 00 00 00 08 00 00 00 00 00 00 00 00 00 00 30 71 C0 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 10 00 00 00 B2 02 00 00 08 00 00 00 06 00 00 00 00 00 00 00 53 55 50 4C 41 ]
Relay::handleChannelConfig, func 130, configtype 0, configsize 0
Relay::handleChannelConfig, func 130, configtype 0, configsize 0
Recv: [53 55 50 4C 41 15 11 00 00 00 B2 02 00 00 08 00 00 00 07 00 00 00 00 00 00 00 53 55 50 4C 41 ]
Relay::handleChannelConfig, func 130, configtype 0, configsize 0
Relay::handleChannelConfig, func 130, configtype 0, configsize 0
Binary[4]: processing channel config
Binary[5]: processing channel config
Binary[6]: processing channel config
Binary[7]: processing channel config
Restarting OneWire...
Restarting OneWire...
Restarting OneWire...
A

 ets Jan  8 2013,rst cause:1, boot mode:(3,6)

load 0x4010f000, len 3424, room 16
tail 0
chksum 0x2e
load 0x3fff20b8, len 40, room 8
tail 0
chksum 0x2b
csum 0x2b
v000a39c0
~ld
rf cal sector: 252
freq trace enable 0
rf[112] : 00▒Config read
Key: 0 Value: ▒]i▒▒,▒t▒Ң▒▒O
Key: 1 Value: ▒ly▒yQ▒U
                      ۚE▒▒w
Key: 2 Value: SmartHouse
Key: 3 Value: pass
Key: 4 Value: admin
Key: 5 Value: pass
Key: 6 Value: GUI Generic - test
Key: 7 Value: svr11.supla.org
Key: 8 Value: mail
Key: 9 Value: 4
Key: 10 Value: 4
Key: 11 Value: 4
Key: 12 Value: 1
Key: 13 Value:
Key: 14 Value: 1
Key: 15 Value:
Key: 16 Value:
Key: 17 Value:
Key: 18 Value:
Key: 19 Value:
Key: 20 Value:
Key: 21 Value: 1
Key: 22 Value:
Key: 23 Value:
Key: 24 Value: ,,0,1,0,2,0,1,,,,,0,2,,,1,,,,,,,,,,,
Key: 25 Value: ,,0,1,0,2,0,,,,,,1,2,,,1,,,,,,,,,,,,
Key: 26 Value: ,,1,1,0,2,0,,,,,,2,2,,,1,1,,,,,,,,,,
Key: 27 Value: 1,6,0,1,0,2,0,,,,,,3,2,,,1,,,,,,,,,,
Key: 28 Value: 1,10,0,0,0,0,0,,,,,,0,3,,,0,,,,,,,,,
Key: 29 Value: 1,9,0,0,0,0,0,,,,,,1,3,,,0,,,,,,,,,,
Key: 30 Value: ,,0,0,0,0,0,,,,,,2,3,,,0,,,,,,,,,,,,
Key: 31 Value: ,,0,0,0,0,0,,,,,,3,3,,,0,,,,,,,,,,,,
Key: 32 Value:
Key: 33 Value:
Key: 34 Value:
Key: 35 Value:
Key: 36 Value: 1,1,1,,0,,0,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 37 Value: 2,1,1,,0,,0,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 38 Value: 3,1,1,,0,,0,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 39 Value: 1,25,,,0,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 40 Value: 4,1,1,,0,,0,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 41 Value: ,,,0,,2,0,,,,,,,,,,1,,,,,,,,,,,,,,,,
Key: 42 Value:
Key: 43 Value:
Key: 44 Value:
Key: 45 Value: 1
Key: 46 Value:
Key: 47 Value:
Key: 48 Value:
Key: 49 Value:
Key: 50 Value:
Key: 51 Value:
Key: 52 Value:
Key: 53 Value:
Key: 54 Value:
Key: 55 Value:
Key: 56 Value:
Key: 57 Value:
Key: 58 Value: 1
Key: 59 Value: 0
Key: 60 Value:
Key: 61 Value:
Key: 62 Value:
Key: 63 Value:
Key: 64 Value:
Key: 65 Value:
Key: 66 Value:
Key: 67 Value:
Key: 68 Value:
Key: 69 Value:
Key: 70 Value:
Key: 71 Value:
Key: 72 Value:
Key: 73 Value:
Key: 74 Value: 0.25
Key: 75 Value: 0.4
Key: 76 Value:
Key: 77 Value:
Key: 78 Value:
Key: 79 Value:
Key: 80 Value: 0
Key: 81 Value: ,0,3,3,0,0,0,,0,0,0,
Key: 82 Value:
Key: 83 Value:
Key: 84 Value:
Key: 85 Value:
Key: 86 Value:
Key: 87 Value:
Key: 88 Value:
Key: 89 Value: 1,0,2,3,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 90 Value: ,,,,,,,0,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Key: 91 Value:
Key: 92 Value:
Key: 93 Value:
Key: 94 Value:
Key: 95 Value:
Key: 96 Value:
Key: 97 Value:
Key: 98 Value:
PCF8574 is connected address: 22
Button[0]::setMulticlickTime: 250
Button[0]::setHoldTime: 400
Button[1]::setMulticlickTime: 250
Button[1]::setHoldTime: 400
Button[2]::setMulticlickTime: 250
Button[2]::setHoldTime: 400
Button[3]::setMulticlickTime: 250
Button[3]::setHoldTime: 400
Button[4]::setMulticlickTime: 450
Button[4]::setHoldTime: 5000
Channel(8) value changed to -275.0
Button[5]::setMulticlickTime: 200
Button[5]::setHoldTime: 400
Supla - starting initialization
Storage initialization
readStorage: 8; Read: [53 55 50 4C 41 1 0 1 ]
Storage: Number of sections 1
Reading section: 0
readStorage: 7; Read: [3 16 0 5A E0 5A E0 ]
Section type: 3; size: 22
CRC1 57434, CRC2 57434, CRC calc 57434
Button[0]::onLoadConfig: skip
Button[1]::onLoadConfig: skip
Button[2]::onLoadConfig: skip
Button[3]::onLoadConfig: skip
Channel function missing. Using SW defaults
Binary[4] setServerInvertLogic 0
Binary[4] config serverInvertLogic 0
Channel function missing. Using SW defaults
Binary[5] setServerInvertLogic 0
Binary[5] config serverInvertLogic 0
Channel function missing. Using SW defaults
Binary[6] setServerInvertLogic 0
Binary[6] config serverInvertLogic 0
Channel function missing. Using SW defaults
Binary[7] setServerInvertLogic 0
Binary[7] config serverInvertLogic 0
Button[4] enabling IN as config button
Channel[8] temperature correction 0.000000
Channel[8] humidity correction 0.000000
RGBWBase[9] button control type: 0
Button[5]::onLoadConfig: skip
Validating storage state section with current device configuration
Storage state section validation completed. Loading elements state...
readStorage: 4; Read: [0 0 0 0 ]
readStorage: 1; Read: [0 ]
readStorage: 4; Read: [0 0 0 0 ]
readStorage: 1; Read: [0 ]
readStorage: 4; Read: [0 0 0 0 ]
readStorage: 1; Read: [0 ]
readStorage: 4; Read: [0 0 0 0 ]
readStorage: 1; Read: [0 ]
readStorage: 1; Read: [0 ]
readStorage: 1; Read: [64 ]
Relay[0] turn OFF (duration 0 ms)
 **** Digital write[0], gpio: 12; value 0
Relay[0] turn OFF (duration 0 ms)
 **** Digital write[0], gpio: 12; value 0
Pin 1, pullUp 1, invertLogic 1, state 1
Relay[1] turn OFF (duration 0 ms)
 **** Digital write[1], gpio: 13; value 0
Relay[1] turn OFF (duration 0 ms)
 **** Digital write[1], gpio: 13; value 0
Pin 0, pullUp 1, invertLogic 1, state 1
Relay[2] turn OFF (duration 0 ms)
 **** Digital write[2], gpio: 14; value 0
Relay[2] turn OFF (duration 0 ms)
 **** Digital write[2], gpio: 14; value 0
Pin 2, pullUp 1, invertLogic 1, state 1
Relay[3] turn OFF (duration 0 ms)
 **** Digital write[3], gpio: 16; value 0
Relay[3] turn OFF (duration 0 ms)
 **** Digital write[3], gpio: 16; value 0
Pin 3, pullUp 1, invertLogic 1, state 1
Channel(4) value changed to 1
Channel(5) value changed to 1
Channel(6) value changed to 1
Channel(7) value changed to 1
Pin 0, pullUp 1, invertLogic 1, state 1
RGBWBase[9] TURN off onInit
RGBW: 0,0,0,0,0
Pin 0, pullUp 1, invertLogic 1, state 1
GUID: AF5D116985992CEFBF74E8D2A284904F
Device name: GUI Generic - test
Device software version: **** Analog write[-1], gpio: 15; value 0
 GG v7.8.14
Initializing network layer
Network AP/hostname: GUI-GENERIC---TEST-840D8E82F8B8
Using Supla protocol version 21
Current status: [5] SuplaDevice initialized
Enter normal mode
WiFi: establishing connection with SSID: "SmartHouse"
Connected BSSID: C6:C9:E3:0C:6B:48
local IP: 192.168.1.187
subnetMask: 255.255.255.0
gatewayIP: 192.168.1.3
Signal strength (RSSI): -59 dBm
Establishing NOT encrypted connection with: svr11.supla.org (port: 2015)
Connected to Supla Server
Initializing SRPC
LAST STATE ADDED: Register in progress
Current status: [10] Register in progress
CH #0, type: 2900, FuncList: 0xEF, default: 130, flags: 0x1010000, value: [00 00 00 00 00 00 00 00]
CH #1, type: 2900, FuncList: 0xEF, default: 130, flags: 0x1010000, value: [00 00 00 00 00 00 00 00]
CH #2, type: 2900, FuncList: 0xEF, default: 130, flags: 0x1010000, value: [00 00 00 00 00 00 00 00]
CH #3, type: 2900, FuncList: 0xEF, default: 130, flags: 0x1010000, value: [00 00 00 00 00 00 00 00]
CH #4, type: 1000, FuncList: 0x0, default: 0, flags: 0x8010000, value: [01 00 00 00 00 00 00 00]
CH #5, type: 1000, FuncList: 0x0, default: 0, flags: 0x8010000, value: [01 00 00 00 00 00 00 00]
CH #6, type: 1000, FuncList: 0x0, default: 0, flags: 0x8010000, value: [01 00 00 00 00 00 00 00]
CH #7, type: 1000, FuncList: 0x0, default: 0, flags: 0x8010000, value: [01 00 00 00 00 00 00 00]
CH #8, type: 3034, FuncList: 0x0, default: 40, flags: 0x8010000, value: [00 00 00 00 00 30 71 c0]
CH #9, type: 4000, FuncList: 0x0, default: 180, flags: 0x10100, value: [00 00 00 00 00 00 00 00]
Send: [53 55 50 4C 41 15 01 00 00 00 45 00 00 00 42 03 00 00 73 77 69 74 61 6C 61 6D 61 72 65 6B 40 69 6E 74 65 72 69 61 2E 70 6C 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 AB 6C 79 9D 79 51 C2 55 0A DB 9A 45 A6 F6 86 77 AF 5D 11 69 85 99 2C EF BF 74 E8 D2 A2 84 90 4F 47 55 49 20 47 65 6E 65 72 69 63 20 2D 20 74 65 73 74 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 01 00 00 00 46 00 00 00 07 00 00 00 03 00 00 00 78 15 01 53 55 50 4C 41 ]
Device registered (activity timeout 120 s, server version: 21, server min version: 1)
LAST STATE ADDED: Registered and ready
Current status: [17] Registered and ready
Changing activity timeout to 30
Send: [53 55 50 4C 41 15 02 00 00 00 D2 00 00 00 01 00 00 00 1E ]
Send: [53 55 50 4C 41 ]
Relay[0]: updating timer value: remainingTime=0 state=0
SRPC sedning: remaining time 0, channel 0, state 0
Send: [53 55 50 4C 41 15 03 00 00 00 69 00 00 00 E3 00 00 00 00 32 DD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 04 00 00 00 A8 02 00 00 06 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 02 00 00 00 AD 02 00 00 1B 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 53 55 50 4C 41 53 55 50 4C 41 15 03 00 00 00 AB 02 00 00 01 00 00 00 04 53 55 50 4C 41 53 55 50 4C 41 15 04 00 00 00 AB 02 00 00 01 00 00 00 05 53 55 50 4C 41 53 55 50 4C 41 15 05 00 00 00 AB 02 00 00 01 00 00 00 06 53 55 50 4C 41 53 55 50 4C 41 15 06 00 00 00 AB 02 00 00 01 00 00 00 07 53 55 50 4C 41 53 55 50 4C 41 15 07 00 00 00 AA 02 00 00 28 00 00 00 08 28 00 00 00 00 20 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 53 55 50 4C 41 53 55 50 4C 41 15 08 00 00 00 AB 02 00 00 01 00 00 00 08 53 55 50 4C 41 53 55 50 4C 41 15 09 00 00 00 DC 00 00 00 03 00 00 00 1E 0A F0 53 55 ]
Received new device config
Sending device config result OK (1)
Send: [53 55 50 4C 41 15 05 00 00 00 B7 02 00 00 0A 00 00 00 01 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Relay[1]: updating timer value: remainingTime=0 state=0
SRPC sedning: remaining time 0, channel 1, state 0
Send: [53 55 50 4C 41 15 06 00 00 00 69 00 00 00 E3 00 00 00 01 32 DD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 07 00 00 00 A8 02 00 00 06 00 00 00 01 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [50 4C 41 53 55 50 4C 41 15 0A 00 00 00 B2 02 00 00 08 00 00 00 00 82 00 00 00 00 00 00 53 55 50 4C 41 ]
Received ChannelConfigFinished for channel 4
Binary[4]: setting default channel config
Binary[4]: processing local channel config
Binary[4] setServerInvertLogic 0
Relay[2]: updating timer value: remainingTime=0 state=0
SRPC sedning: remaining time 0, channel 2, state 0
Send: [53 55 50 4C 41 15 08 00 00 00 69 00 00 00 E3 00 00 00 02 32 DD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 09 00 00 00 A8 02 00 00 06 00 00 00 02 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 0B 00 00 00 B2 02 00 00 08 00 00 00 01 82 00 00 00 00 00 00 53 55 50 4C 41 ]
Received ChannelConfigFinished for channel 5
Binary[5]: setting default channel config
Binary[5]: processing local channel config
Binary[5] setServerInvertLogic 0
Relay[3]: updating timer value: remainingTime=0 state=0
SRPC sedning: remaining time 0, channel 3, state 0
Send: [53 55 50 4C 41 15 0A 00 00 00 69 00 00 00 E3 00 00 00 03 32 DD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 0B 00 00 00 A8 02 00 00 06 00 00 00 03 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 0C 00 00 00 B2 02 00 00 08 00 00 00 02 82 00 00 00 00 00 00 53 55 50 4C 41 ]
Received ChannelConfigFinished for channel 6
Binary[6]: setting default channel config
Binary[6]: processing local channel config
Binary[6] setServerInvertLogic 0
Send: [53 55 50 4C 41 15 0C 00 00 00 67 00 00 00 0E 00 00 00 04 00 00 00 00 00 01 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 0D 00 00 00 A8 02 00 00 06 00 00 00 04 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Received ChannelConfigFinished for channel 7
Binary[7]: setting default channel config
Binary[7]: processing local channel config
Binary[7] setServerInvertLogic 0
Send: [53 55 50 4C 41 15 0E 00 00 00 67 00 00 00 0E 00 00 00 05 00 00 00 00 00 01 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 0F 00 00 00 A8 02 00 00 06 00 00 00 05 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 0D 00 00 00 B2 02 00 00 08 00 00 00 03 82 00 00 00 00 00 00 53 55 50 4C 41 ]
Received SetChannelConfig for channel 8, function 40, config type 0, config size 32
handleChannelConfig, func 40, configtype 0, configsize 32
Channel[8] temperature correction 0.000000
Channel[8] humidity correction 0.000000
Channel[8] config changed offline flag 0
Sending channel config result OK (1)
Send: [53 55 50 4C 41 15 10 00 00 00 B4 02 00 00 03 00 00 00 01 00 08 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 11 00 00 00 67 00 00 00 0E 00 00 00 06 00 00 00 00 00 01 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 12 00 00 00 A8 02 00 00 06 00 00 00 06 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Received ChannelConfigFinished for channel 8
Send: [53 55 50 4C 41 15 13 00 00 00 67 00 00 00 0E 00 00 00 07 00 00 00 00 00 01 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 15 14 00 00 00 A8 02 00 00 06 00 00 00 07 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 0E 00 00 00 B2 02 00 00 08 00 00 00 04 00 00 00 00 00 00 00 53 55 50 4C 41 ]
Activity timeout set to 30 s
Recv: [53 55 50 4C 41 15 0F 00 00 00 B2 02 00 00 08 00 00 00 05 00 00 00 00 00 00 00 53 55 50 4C 41 ]
Relay::handleChannelConfig, func 130, configtype 0, configsize 0
Send: [53 55 50 4C 41 15 15 00 00 00 67 00 00 00 0E 00 00 00 08 00 00 00 00 00 00 00 00 00 00 30 71 C0 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 15 10 00 00 00 B2 02 00 00 08 00 00 00 06 00 00 00 00 00 00 00 53 55 50 4C 41 ]
Relay::handleChannelConfig, func 130, configtype 0, configsize 0
Relay::handleChannelConfig, func 130, configtype 0, configsize 0
Recv: [53 55 50 4C 41 15 11 00 00 00 B2 02 00 00 08 00 00 00 07 00 00 00 00 00 00 00 53 55 50 4C 41 ]
Relay::handleChannelConfig, func 130, configtype 0, configsize 0
Binary[4]: processing channel config
Binary[5]: processing channel config
Binary[6]: processing channel config
Binary[7]: processing channel config
Restarting OneWire...
Restarting OneWire...

[krycha88]

Poprawiłem miejsce występowania błędu, ale to i tak nie rozwiąże twojego problemu z DS18B20.

[mareks6]

tak jak mówiłem - firmware generowany w sierpniu nie sprawia tego problemu.

Co masz na myśli że u mnie to nie pomoże? Przypominam, że logi były robione ze skonfigurowanym lecz nie podłączonym DS