Mam jeszcze jedno pytanie, rozumiem że te parametry muszę ustawić dla każdego urządzenia?
Obecnie po dodaniu urządzenia pokazuje poziom baterii na 40%.
Zgłoszenia nowych urządzeń [bramka Zigbee]
Moderator: vajera
-
Lector
- Posts: 2471
- Joined: Fri Nov 17, 2017 2:26 pm
- Location: Poznań
- Has thanked: 13 times
- Been thanked: 25 times
Spróbuj wyłączyć ostania opcję - disable Battery voltage.robertklepacki94 wrote: Fri Oct 24, 2025 5:58 am Mam jeszcze jedno pytanie, rozumiem że te parametry muszę ustawić dla każdego urządzenia?
Obecnie po dodaniu urządzenia pokazuje poziom baterii na 40%.
Zrzut ekranu 2025-10-24 o 07.53.29.png
Niespełniony automatyk. 
https://3d-lamp.photos/
https://pool.lector.top/
https://3d-lamp.photos/
https://pool.lector.top/
-
vajera
- Posts: 7293
- Joined: Wed Oct 31, 2018 7:58 am
- Location: Biedrusko
- Has thanked: 291 times
- Been thanked: 161 times
Zajrzyj tutaj:robertklepacki94 wrote: Fri Oct 24, 2025 5:58 am Mam jeszcze jedno pytanie, rozumiem że te parametry muszę ustawić dla każdego urządzenia?
Obecnie po dodaniu urządzenia pokazuje poziom baterii na 40%.
Zrzut ekranu 2025-10-24 o 07.53.29.png
viewtopic.php?p=208867#p208867
Bramka Zigbee <=> SUPLA
Więcej informacji tutaj:
https://forum.supla.org/viewforum.php?f=127
FAQ https://forum.supla.org/viewtopic.php?t=17277
Więcej informacji tutaj:
https://forum.supla.org/viewforum.php?f=127
FAQ https://forum.supla.org/viewtopic.php?t=17277
-
zokopian
- Posts: 123
- Joined: Fri Jan 11, 2019 9:00 pm
vajera wrote: Thu Oct 23, 2025 7:31 pm
To urządzenie przedstawia się niezgodnie ze standardem Zigbee - zrobiłem takie małe obejście w 0.9.113-23/10/2025 - daj logi z parowania.
Code: Select all
[ 1][V][NetworkServer.h:41] NetworkServer(): NetworkServer::e[48] - Freq=100 00000Hz
[ 31323][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[ 31323][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
Send: [53 55 50 4C 41 17 0D 00 00 00 28 00 00 00 10 00 00 00 8A C7 FB 68 00 00 00 00 E1 41 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 17 0D 00 00 00 32 00 00 00 10 00 00 00 6B AB FB 68 00 00 00 00 9C 1F 02 00 00 00 00 00 53 55 50 4C 41 ]
[ 60001][I][Z2S_Gateway.ino:774] loop(): New UTC time 814646286, new local time 814646286
[ 60002][I][Z2S_Gateway.ino:820] loop():
Local Time Cluster Time status attribute 2
UTC time attribute 814646286
local time attribute 814646286
[ 60004][I][z2s_web_gui.cpp:754] fillMemoryUptimeInformation(): Memory & uptime information <b><i>Flash chip real size:</b></i> 4194304 B <b>| <i>Free Sketch Space:</b></i> 2621440 B<br><b><i>HeapSize:</b></i> 359148 B <b>| <i>FreeHeap:</b></i> 89212 B <b>| <i>MinimalFreeHeap:</b></i> 38284 B <b>| <i>MaxAllocHeap:</b></i> 67572 B<br><b><i>uxTaskGetStackHighWaterMark:</b></i> 3024 B <br><b><i>Total PSRAM:</b></i> 0 B <b>| <i>Free PSRAM:</b></i> 0 B<br><br><b><i>Local time:</i></b> Fri Oct 24 18:38:06 2025
<b><i>Supla uptime:</i></b> 60 s
[ 60009][I][Z2S_Gateway.ino:832] loop():
Memory information:
Flash chip real size: 4194304 B
Free Sketch Space: 2621440 B
Free Heap: 86900 B
Minimal Free Heap: 38284 B
HeapSize: 359148 B
MaxAllocHeap: 67572 B
Supla uptime: 60 s
[ 64749][V][ZigbeeCore.cpp:264] openNetwork(): Opening network for joining for 180 seconds
[ 65219][I][ZigbeeCore.cpp:427] esp_zb_app_signal_handler(): Network(0x688e) is open for 180 seconds
[ 65220][I][Z2S_Gateway.ino:216] Z2S_onOpenNetwork(): Network open for 180 s
[ 65220][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[ 65221][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[ 65221][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
Send: [53 55 50 4C 41 17 0E 00 00 00 28 00 00 00 10 00 00 00 A3 C7 FB 68 00 00 00 00 48 4E 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 17 0E 00 00 00 32 00 00 00 10 00 00 00 84 AB FB 68 00 00 00 00 B0 20 02 00 00 00 00 00 53 55 50 4C 41 ]
Send: [53 55 50 4C 41 17 0F 00 00 00 28 00 00 00 10 00 00 00 BC C7 FB 68 00 00 00 00 7C 5D 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 17 0F 00 00 00 32 00 00 00 10 00 00 00 9D AB FB 68 00 00 00 00 93 2E 02 00 00 00 00 00 53 55 50 4C 41 ]
[108461][V][ZigbeeCore.cpp:472] esp_zb_app_signal_handler(): ZDO signal: NWK Device Associated (0x12), status: ESP_OK
[108763][D][ZigbeeCore.cpp:479] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[108763][D][ZigbeeCore.cpp:480] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 0, src_endpoint: 0, dst_addr_mode: 255
APSDE INDICATION - src_addr_mode: 55, cluster_id: 0x0013, asdu_length: 12
APSDE INDICATION - dst_short_addr: 0xfffd, src_short_addr: 0x3c37
APSDE INDICATION - profile_id: 0x0000, security_status: 0, lqi: 132, rx_time: 0
[108765][I][ZigbeeCore.cpp:370] esp_zb_app_signal_handler(): New device commissioned or rejoined (short: 0x3c37)
[108765][V][ZigbeeCore.cpp:374] esp_zb_app_signal_handler(): Device capabilities: 0x8e
[108808][D][ZigbeeCore.cpp:479] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[108809][D][ZigbeeCore.cpp:480] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 0, src_endpoint: 0, dst_addr_mode: 255
APSDE INDICATION - src_addr_mode: 0, cluster_id: 0x8006, asdu_length: 5
APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0x3c37
APSDE INDICATION - profile_id: 0x0000, security_status: 0, lqi: 132, rx_time: 0
[108810][D][ZigbeeGateway.cpp:353] find_Cb(): Broadcast short address returned - trying to retour
short address(0x3c37), endpoint(255)
[108813][I][ZigbeeGateway.cpp:899] printJoinedDevices(): joined devices:
[108813][I][ZigbeeGateway.cpp:902] printJoinedDevices(): Device on endpoint 255, short address: 0x3c37
[108814][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[108814][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[108816][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[108817][I][ZigbeeGateway.cpp:501] zbQueryDeviceBasicCluster(): Query basic cluster attribute 0x4
[108852][D][ZigbeeCore.cpp:479] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[108853][D][ZigbeeCore.cpp:480] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 3, dst_addr_mode: 255
APSDE INDICATION - src_addr_mode: 0, cluster_id: 0x0000, asdu_length: 13
APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0x3c37
APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 127, rx_time: 0
[108855][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0x0, command id: 1
[108855][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x3, dst endpoint 0x1
[108856][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 1, disable_default_response 1, is_manuf_specific 0
[108856][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[108857][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 12 size: 10
[108857][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x04
[108857][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00
[108858][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00
[108858][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x42
[108858][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x05
[108859][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x4F
[108859][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x53
[108860][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x52
[108860][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x41
[108860][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x4D
[108861][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0x3c37, 0x3c37, 0x0, 0x0
[108861][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[108862][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1000) callback
[108862][V][ZigbeeHandlers.cpp:262] zb_cmd_read_attr_resp_handler(): Read attribute response: from address(0x3c37) src endpoint(3) to dst endpoint(1) cluster(0x0)
[108863][V][ZigbeeHandlers.cpp:270] zb_cmd_read_attr_resp_handler(): Read attribute response: status(0), cluster(0x0), attribute(0x4), type(0x42), value(5)
[108864][I][ZigbeeGateway.cpp:555] zbReadBasicCluster(): Peer Manufacturer is "OSRAM"
[109817][I][ZigbeeGateway.cpp:507] zbQueryDeviceBasicCluster(): basic tsn 0x0
[109817][I][ZigbeeGateway.cpp:501] zbQueryDeviceBasicCluster(): Query basic cluster attribute 0x5
[109874][D][ZigbeeCore.cpp:479] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[109875][D][ZigbeeCore.cpp:480] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 1, src_endpoint: 3, dst_addr_mode: 255
APSDE INDICATION - src_addr_mode: 0, cluster_id: 0x0000, asdu_length: 15
APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0x3c37
APSDE INDICATION - profile_id: 0x0104, security_status: 0, lqi: 132, rx_time: 0
[109877][I][ZigbeeHandlers.cpp:138] zb_raw_cmd_handler(): cluster id: 0x0, command id: 1
[109877][I][ZigbeeHandlers.cpp:141] zb_raw_cmd_handler(): src endpoint (0x3, dst endpoint 0x1
[109878][I][ZigbeeHandlers.cpp:145] zb_raw_cmd_handler(): is common comand 1, disable_default_response 1, is_manuf_specific 0
[109878][I][ZigbeeHandlers.cpp:149] zb_raw_cmd_handler(): manuf_specific 0x0
[109879][I][ZigbeeHandlers.cpp:153] zb_raw_cmd_handler(): RAW bufid: 14 size: 12
[109879][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x05
[109879][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00
[109880][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x00
[109880][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x42
[109880][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x07
[109881][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x50
[109881][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x6C
[109881][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x75
[109882][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x67
[109882][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x20
[109882][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x30
[109883][I][ZigbeeHandlers.cpp:156] zb_raw_cmd_handler(): 0x31
[109883][I][ZigbeeHandlers.cpp:165] zb_raw_cmd_handler(): ZigbeeHandlers rawCMD 0x3c37, 0x3c37, 0x0, 0x0
[109884][I][ZigbeeHandlers.cpp:191] zb_raw_cmd_handler(): ----------------------------raw command not processed------------------------------------------------------------
[109884][I][ZigbeeHandlers.cpp:42] zb_action_handler(): Receive Zigbee action(0x1000) callback
[109885][V][ZigbeeHandlers.cpp:262] zb_cmd_read_attr_resp_handler(): Read attribute response: from address(0x3c37) src endpoint(3) to dst endpoint(1) cluster(0x0)
[109886][V][ZigbeeHandlers.cpp:270] zb_cmd_read_attr_resp_handler(): Read attribute response: status(0), cluster(0x0), attribute(0x5), type(0x42), value(7)
[109886][I][ZigbeeGateway.cpp:565] zbReadBasicCluster(): Peer Model is "Plug 01"
[110818][I][ZigbeeGateway.cpp:507] zbQueryDeviceBasicCluster(): basic tsn 0x1
[110818][I][Z2S_Gateway.ino:1009] loop(): LIST matched OSRAM::Plug 01, entry # 133, endpoints # 1, endpoints 0x0::0x0,0x0::0x0,0x0::0x0,0x0::0x0
[110819][I][Z2S_Gateway.ino:1037] loop(): DESC matched 0x4001, 1, 0x6, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, endpoint 0x1
[110820][D][ZigbeeGateway.cpp:655] bindDeviceCluster(): Requesting ZED (0x3c37), endpoint (0x1), cluster_id (0x6) to bind ZC
[110896][D][ZigbeeCore.cpp:479] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[110896][D][ZigbeeCore.cpp:480] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 0, src_endpoint: 0, dst_addr_mode: 255
APSDE INDICATION - src_addr_mode: 0, cluster_id: 0x8021, asdu_length: 2
APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0x3c37
APSDE INDICATION - profile_id: 0x0000, security_status: 0, lqi: 112, rx_time: 0
[110898][I][ZigbeeGateway.cpp:315] bindCb(): ZED (0x3c37), endpoint (0x1) cluster (0x6) has bounded to ZC
[110899][I][ZigbeeGateway.cpp:332] bindCb(): Semaphore give in binding
[111021][D][ZigbeeGateway.cpp:716] bindDeviceCluster(): Requesting ZC to bind ZED (0x3c37), endpoint (0x1), cluster_id (0x6)
[111022][D][ZigbeeCore.cpp:479] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[111023][D][ZigbeeCore.cpp:480] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 0, src_endpoint: 0, dst_addr_mode: 255
APSDE INDICATION - src_addr_mode: 0, cluster_id: 0x0021, asdu_length: 22
APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0x0000
APSDE INDICATION - profile_id: 0x0000, security_status: 0, lqi: 0, rx_time: 0
[111027][D][ZigbeeCore.cpp:479] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[111028][D][ZigbeeCore.cpp:480] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 0, src_endpoint: 0, dst_addr_mode: 255
APSDE INDICATION - src_addr_mode: 0, cluster_id: 0x8021, asdu_length: 2
APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0x0000
APSDE INDICATION - profile_id: 0x0000, security_status: 0, lqi: 0, rx_time: 0
[111030][I][ZigbeeGateway.cpp:312] bindCb(): ZC has bounded to ZED (0x3c37), endpoint (0x1) cluster (0x6)
[111030][I][ZigbeeGateway.cpp:332] bindCb(): Semaphore give in binding
[111231][I][z2s_devices_table.cpp:719] Z2S_addZbDeviceTableSlot(): New ZB device - adding to the ZB devices table
[111232][I][z2s_devices_table.cpp:696] Z2S_updateZbDeviceUidIdx(): Manufacturer name: OSRAM, model name: Plug 01, device uid = 10605, devices list index = 133
[111233][D][z2s_little_fs.cpp:25] Z2S_saveFile(): Z2S LittleFs: saving file zb_devices_table_v2.z2s
[111315][I][z2s_devices_table.cpp:1120] Z2S_saveZbDevicesTable(): Zigbee devices table new size(3840) write success!
LittleFsConfig: writing to file "/supla-dev.cfg"
LittleFsConfig: writing to file "/supla-dev.cfg.bak"
[111333][I][z2s_devices_table.cpp:157] Z2S_findChannelNumberSlot(): 7C:B0:3E:AA:00:A3:90:EB, endpoint 0x1, channel type 0xffffffff
[111335][I][z2s_devices_table.cpp:3966] Z2S_addZ2SDevice(): No channel found for address 7C:B0:3E:AA:00:A3:90:EB, adding new one!
[111335][I][z2s_devices_table.cpp:3975] Z2S_addZ2SDevice(): model id 16385, first free slot 0
Channel[0] initial caption set to 'POWER SWITCH'
[111336][D][z2s_little_fs.cpp:25] Z2S_saveFile(): Z2S LittleFs: saving file channels_table_v2.z2s
[111606][D][z2s_little_fs.cpp:25] Z2S_saveFile(): Z2S LittleFs: saving file channels_table_v2.bak
[111864][I][z2s_devices_table.cpp:559] Z2S_saveChannelsTable(): Channels table new size(15360) write success!
LittleFsConfig: writing to file "/supla-dev.cfg"
LittleFsConfig: writing to file "/supla-dev.cfg.bak"
[111890][I][ZigbeeGateway.cpp:1903] sendAttributeWrite(): Sending 'write attribute' command - id (0x4003), type (0x30), size (0x1), value (0xff)
[112091][I][ZigbeeGateway.cpp:1903] sendAttributeWrite(): Sending 'write attribute' command - id (0x8002), type (0x30), size (0x1), value (0x2)
[112494][I][ZigbeeGateway.cpp:1615] setClusterReporting(): _set_config_last_tsn = 4
[112694][I][ZigbeeGateway.cpp:1622] setClusterReporting(): _set_config_last_tsn_flag = 2
Scheduling soft restart in 5000 ms
LAST STATE ADDED: Software reset (108)
[112694][I][Z2S_Gateway.ino:108] supla_callback_bridge(): event(0x22), action(0x4010)
Current status: [41] Software reset
[112700][I][ZigbeeGateway.cpp:1806] sendAttributeRead(): Sending 'read attribute' command
[112706][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[112707][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[112708][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[112900][I][ZigbeeGateway.cpp:1806] sendAttributeRead(): Sending 'read attribute' command
[113100][I][Z2S_virtual_relay.cpp:471] iterateAlways(): current_millis 113100, _last_seen_ms 0
[113100][I][Z2S_virtual_relay.cpp:473] iterateAlways(): current_millis 113100, _last_seen_ms(updated) 0
Channel[0] go offline
Warning! Attempt to write state outside of section size.
Storage: rewriting element state section. All data will be lost.
Wrote 4 bytes to storage at 15
Wrote 7 bytes to storage at 8
Commit
[114725][D][ZigbeeCore.cpp:479] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[114726][D][ZigbeeCore.cpp:480] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 0, src_endpoint: 0, dst_addr_mode: 255
APSDE INDICATION - src_addr_mode: 55, cluster_id: 0x0006, asdu_length: 9
APSDE INDICATION - dst_short_addr: 0xfffd, src_short_addr: 0x3c37
APSDE INDICATION - profile_id: 0x0000, security_status: 0, lqi: 112, rx_time: 0
Reset requested. Reset device
[117696][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[117697][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[117697][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
Wrote 1 bytes to storage at 15
Wrote 1 bytes to storage at 21
Wrote 4 bytes to storage at 22
Wrote 1 bytes to storage at 26
Wrote 7 bytes to storage at 8
Commit
LittleFsConfig: writing to file "/supla-dev.cfg"
LittleFsConfig: writing to file "/supla-dev.cfg.bak"
[117818][V][AP.cpp:108] _onApEvent(): AP Started
[117818][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 130 - AP_START
[117818][V][AP.cpp:88] _onApArduinoEvent(): Arduino AP Event: 130 - AP_START
[117824][V][AP.cpp:112] _onApEvent(): AP Stopped
[117825][V][AP.cpp:108] _onApEvent(): AP Started
[117825][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 131 - AP_STOP
[117825][V][AP.cpp:88] _onApArduinoEvent(): Arduino AP Event: 131 - AP_STOP
[117826][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 130 - AP_START
[117826][V][AP.cpp:88] _onApArduinoEvent(): Arduino AP Event: 130 - AP_START
[117828][V][AP.cpp:112] _onApEvent(): AP Stopped
[117828][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 131 - AP_STOP
[117829][V][AP.cpp:88] _onApArduinoEvent(): Arduino AP Event: 131 - AP_STOP
[117834][V][STA.cpp:216] _onStaEvent(): STA Disconnected: SSID: FRITZ!Box 7590 HN, BSSID: 44:4e:6d:52:d4:81, Reason: 8
[117835][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 113 - STA_DISCONNECTED
[117836][V][STA.cpp:110] _onStaArduinoEvent(): Arduino STA Event: 113 - STA_DISCONNECTED
[117836][W][STA.cpp:137] _onStaArduinoEvent(): Reason: 8 - ASSOC_LEAVE
WiFi Station disconnected
[117839][V][STA.cpp:190] _onStaEvent(): STA Stopped
[117840][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 111 - STA_STOP
[117840][V][STA.cpp:110] _onStaArduinoEvent(): Arduino STA Event: 111 - STA_STOP
[117845][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 100 - WIFI_OFF
[117845][V][NetworkInterface.cpp:262] destroyNetif(): Unregistered event handler
Resetting in 0.5s...
See you soon!
ESP-ROM:esp32c6-20220919
Build:Sep 19 2022
rst:0xc (SW_CPU),boot:0x1e (SPI_FAST_FLASH_BOOT)
Saved PC:0x4001975a
SPIWP:0xee
mode:DIO, clock div:2
load:0x40875730,len:0x12e0
load:0x4086b910,len:0xda8
load:0x4086e610,len:0x3180
entry 0x4086b910
[ 1][V][NetworkServer.h:41] NetworkServer(): NetworkServer::NetworkServer(port=23, ...)
[ 9][V][NetworkServer.h:41] NetworkServer(): NetworkServer::NetworkServer(port=1234, ...)
[ 18][V][ZigbeeEP.cpp:22] ZigbeeEP(): Endpoint: 1
[ 42][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type USB_DM (38) successfully set to 0x4207b932
[ 53][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 12 successfully set to type USB_DM (38) with bus 0x4082052c
[ 64][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type USB_DP (39) successfully set to 0x4207b932
[ 75][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 13 successfully set to type USB_DP (39) with bus 0x4082052c
=========== Before Setup Start ===========
Chip Info:
------------------------------------------
Model : ESP32-C6
Package : 1
Revision : 0.01
Cores : 1
CPU Frequency : 160 MHz
XTAL Frequency : 40 MHz
Features Bitfield : 0x00000052
Embedded Flash : No
Embedded PSRAM : No
2.4GHz WiFi : Yes
Classic BT : No
BT Low Energy : Yes
IEEE 802.15.4 : Yes
------------------------------------------
INTERNAL Memory Info:
------------------------------------------
Total Size : 359148 B ( 350.7 KB)
Free Bytes : 304232 B ( 297.1 KB)
Allocated Bytes : 42284 B ( 41.3 KB)
Minimum Free Bytes: 304232 B ( 297.1 KB)
Largest Free Block: 286708 B ( 280.0 KB)
------------------------------------------
Flash Info:
------------------------------------------
Chip Size : 4194304 B (4 MB)
Block Size : 65536 B ( 64.0 KB)
Sector Size : 4096 B ( 4.0 KB)
Page Size : 256 B ( 0.2 KB)
Bus Speed : 80 MHz
Flash Frequency : 80 MHz (source: 80 MHz, divider: 1)
Bus Mode : QIO
------------------------------------------
Partitions Info:
------------------------------------------
nvs : addr: 0x00009000, size: 20.0 KB, type: DATA, subtype: NVS
otadata : addr: 0x0000E000, size: 8.0 KB, type: DATA, subtype: OTA
app0 : addr: 0x00010000, size: 2560.0 KB, type: APP, subtype: OTA_0
spiffs : addr: 0x00290000, size: 1384.0 KB, type: DATA, subtype: SPIFFS
zb_storage : addr: 0x003EA000, size: 16.0 KB, type: DATA, subtype: FAT
zb_fct : addr: 0x003EE000, size: 4.0 KB, type: DATA, subtype: FAT
rcp_fw : addr: 0x003EF000, size: 4.0 KB, type: DATA, subtype: SPIFFS
coredump : addr: 0x003F0000, size: 64.0 KB, type: DATA, subtype: COREDUMP
------------------------------------------
Software Info:
------------------------------------------
Compile Date/Time : Oct 23 2025 19:23:13
Compile Host OS : linux
ESP-IDF Version : v5.5.1-255-g07e9bf4970
Arduino Version : 3.3.2
------------------------------------------
Board Info:
------------------------------------------
Arduino Board : ESP32C6_DEV
Arduino Variant : esp32c6
Arduino FQBN : esp32:esp32:esp32c6:PartitionScheme=custom,ZigbeeMode=zczr,FlashSize=4M,CDCOnBoot=cdc,DebugLevel=verbose
============ Before Setup End ============
[ 198][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 17 successfully set to type UART_RX (2) with bus 0x40816890
[ 198][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x4208189a
[ 199][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 16 successfully set to type UART_TX (3) with bus 0x40816890
[ 199][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x4208185e
[ 200][I][Z2S_Gateway.ino:355] setup(): setup start
[ 200][I][z2s_devices_table.cpp:7103] printSizeOfClasses():
Relay 136 - VirtualRelay 136 - Z2S_VirtualRelay 200
HvacBase 1032 - HvacBaseEE 1040 - Z2S_trv_interface 184
VirtualSceneSwitch 144
IPAddress 28
NetworkServer 44
NetworkClient 52
[ 208][I][Z2S_Gateway.ino:377] setup(): Sanity check time 7
[ 209][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type GPIO (1) successfully set to 0x4207ecbc
[ 209][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 9 successfully set to type GPIO (1) with bus 0xa
[ 210][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type GPIO (1) successfully set to 0x4207ecbc
[ 211][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 3 successfully set to type GPIO (1) with bus 0x4
[ 211][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type GPIO (1) successfully set to 0x4207ecbc
[ 212][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 14 successfully set to type GPIO (1) with bus 0xf
Storage initialization
readStorage: 8; Read: [53 55 50 4C 41 1 0 1 ]
Storage: Number of sections 1
Reading section: 0
readStorage: 7; Read: [3 C 0 D 55 D 55 ]
Section type: 3; size: 12
storedCRC 21773, CRC calc 21773
LittleFsConfig: file "/supla-dev.cfg" size 375
LittleFsConfig: initializing storage from file...
LittleFsConfig: init result success
LittleFsConfig: writing to file "/supla-dev.cfg"
LittleFsConfig: writing to file "/supla-dev.cfg.bak"
Channel[110] initial caption set to 'Gateway sensors notifications'
Button[0] setHoldTime: 2000
Button[0] setMulticlickTime: 500
Button[0]::configureAsConfigButton
Button[0] setHoldTime: 5000
Button[0] setMulticlickTime: 300
Listing directory: /
FILE: supla-dev.cfg.bak SIZE: 375 LAST WRITE: 2025-10-24 18:39:05
FILE: supla-dev.cfg SIZE: 375 LAST WRITE: 2025-10-24 18:39:05
DIR : z2s_gateway LAST WRITE: 1969-12-31 23:59:59
Listing directory: /z2s_gateway
FILE: actions_index_table.z2s SIZE: 32 LAST WRITE: 1970-01-01 00:00:02
FILE: channels_table_v2.bak SIZE: 15360 LAST WRITE: 2025-10-24 18:38:58
FILE: channels_table_v2.z2s SIZE: 15360 LAST WRITE: 2025-10-24 18:38:57
FILE: zb_devices_table_v2.z2s SIZE: 3840 LAST WRITE: 2025-10-24 18:38:57
Listing directory: /
FILE: supla-dev.cfg.bak SIZE: 375 LAST WRITE: 2025-10-24 18:39:05
FILE: supla-dev.cfg SIZE: 375 LAST WRITE: 2025-10-24 18:39:05
DIR : z2s_gateway LAST WRITE: 1969-12-31 23:59:59
Listing directory: /z2s_gateway
FILE: actions_index_table.z2s SIZE: 32 LAST WRITE: 1970-01-01 00:00:02
FILE: channels_table_v2.bak SIZE: 15360 LAST WRITE: 2025-10-24 18:38:58
FILE: channels_table_v2.z2s SIZE: 15360 LAST WRITE: 2025-10-24 18:38:57
FILE: zb_devices_table_v2.z2s SIZE: 3840 LAST WRITE: 2025-10-24 18:38:57
[ 510][I][z2s_devices_table.cpp:865] Z2S_loadZbDevicesTable(): Z2S_getZbDevicesTableSize 3840, sizeof(z2s_zb_devices_table) 3840, sizeof(z2s_zb_device_params_t) 120, sizeof(bool)1
[ 531][I][z2s_devices_table.cpp:1073] Z2S_loadZbDevicesTable(): Zigbee devices table load success!
[ 532][I][z2s_devices_table.cpp:683] Z2S_updateZbDeviceUidIdx(): device uid = 10605, devices list index = 133
[ 532][I][z2s_devices_table.cpp:341] Z2S_loadChannelsTable(): Z2S_getChannelsTableSize 15360, sizeof(z2s_channels_table) 15360, sizeof(z2s_device_params_t) 120, sizeof(bool)1
[ 555][I][z2s_devices_table.cpp:502] Z2S_loadChannelsTable(): Channels table load success!
[ 555][I][z2s_devices_table.cpp:754] Z2S_addZbDeviceTableSlot(): ZB device already in ZB devices table
[ 556][I][z2s_devices_table.cpp:683] Z2S_updateZbDeviceUidIdx(): device uid = 10605, devices list index = 133
[ 556][I][Z2S_Gateway.ino:496] setup(): Z2S_REBUILD_CHANNELS_ON_START not configured - turning off
[ 557][I][z2s_devices_table.cpp:1294] Z2S_initSuplaChannels(): initSuplaChannels starting
Channel[0] initial caption set to 'POWER SWITCH'
[ 577][I][z2s_devices_table.cpp:1427] Z2S_loadActionsIndexTable(): Zigbee<=>Supla actions index table load SUCCESS!
[ 577][I][z2s_devices_table.cpp:1611] Z2S_initSuplaActions(): actions number: 0
[ 578][D][ZigbeeCore.cpp:110] addGatewayEndpoint(): Endpoint: 1, Device ID: 0x0050
[ 579][I][Z2S_Gateway.ino:565] setup(): Z2S_ENABLE_GUI_ON_START = 2
[ 579][I][Z2S_Gateway.ino:574] setup(): Z2S_FORCE_CONFIG_ON_START not configured - turning off
[ 579][I][Z2S_Gateway.ino:581] setup(): Z2S_GUI_ON_START_DELAY not configured - setting to 0 s
[ 580][I][Z2S_Gateway.ino:591] setup(): Z2S_GATEWAY_MDNS_LOCAL_NAME not configured - using default
SD: allowWorkInOfflineMode is DEPRECATED
SD: initial mode: Start with cfg mode then offline
*** Supla - starting initialization (platform 0)
SD: add flag DEVICE_CONFIG_SUPPORTED
SD: add flag CALCFG_RESTART_DEVICE
*** Supla - Config initalization
SD: add flag CALCFG_ENTER_CFG_MODE
SD: add flag CALCFG_FACTORY_RESET_SUPPORTED
Automatic firmware update is disabled
Device mode: 0
Security level: Skip CA check
*** Supla - Config load for elements
SD: add flag CALCFG_IDENTIFY_DEVICE
RemoteDeviceConfig: Registering field 0x000000001
RemoteDeviceConfig: Registering field 0x000000010
Clock: automaticTimeSync: 1
Channel[110] function missing. Using SW defaults
Button[0] don't load config
PowerCycle: 0 (enabled)
Channel[0] function missing. Using SW defaults
*** Supla - Config load for elements done
*** Supla - Load state storage
Validating storage state section with current device configuration
Storage state section validation successful
readStorage: 1; Read: [6E ]
readStorage: 4; Read: [0 0 0 0 ]
readStorage: 1; Read: [0 ]
Relay[110] restored relay state: OFF
Relay[110] restored remaining countdown timer durationMs: 0
readStorage: 1; Read: [0 ]
readStorage: 4; Read: [0 0 0 0 ]
readStorage: 1; Read: [0 ]
*** Supla - Load state storage done
*** Supla - Init elements
[ 584][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[ 584][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_TX (10) successfully set to 0x420804e6
[ 585][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_RX (11) successfully set to 0x420804e6
[ 586][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 8 successfully set to type RMT_TX (10) with bus 0x40835e38
[ 588][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[ 588][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[ 589][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type GPIO (1) successfully set to 0x4207ecbc
[ 589][V][esp32-hal-rmt.c:142] _rmtDetachBus(): Detaching RMT GPIO Bus
[ 590][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 8 successfully set to type INIT (0) with bus 0x0
[ 590][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 8 successfully set to type GPIO (1) with bus 0x9
Relay[110] turn OFF (duration 0 ms)
Button[0]: Initialized: pin 9, pullUp 1, invertLogic 1, state 1
*** Supla - Init elements done
GUID: 0C382B837CB028B2E59E2BEFB07EAB0F
Device name: Zigbee <=> Supla Gateway
Device software version: 0.9.113-23/10/2025
*** Supla - Initializing network layer
[Wi-Fi] Network AP/hostname: ZIGBEE-SUPLA-GATEW-E4B323B5D2D0
Using Supla protocol version 23
[ 592][I][Z2S_Gateway.ino:108] supla_callback_bridge(): event(0x22), action(0x4010)
Current status: [5] SuplaDevice initialized
Enter normal mode
[Wi-Fi] setNormalMode
*** Supla - Initialization done
*** Self-test ***
TEST: ManufacturerID is 0
TEST failed: ProductID is empty
TEST failed: storage init result is false
TEST failed: missing public RSA key
TEST failed: automatic firmware update is disabled
TEST failed: config encryption is disabled
TEST failed: missing web server
TEST failed: security log is disabled
*** Self-test done ***
=========== After Setup Start ============
INTERNAL Memory Info:
------------------------------------------
Total Size : 359148 B ( 350.7 KB)
Free Bytes : 303940 B ( 296.8 KB)
Allocated Bytes : 41304 B ( 40.3 KB)
Minimum Free Bytes: 296044 B ( 289.1 KB)
Largest Free Block: 286708 B ( 280.0 KB)
------------------------------------------
GPIO Info:
------------------------------------------
GPIO : BUS_TYPE[bus/unit][chan]
--------------------------------------
3 : GPIO
8 : GPIO
9 : GPIO
12 : USB_DM
13 : USB_DP
14 : GPIO
16 : UART_TX[0]
17 : UART_RX[0]
============ After Setup End =============
[ 621][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[ 622][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_TX (10) successfully set to 0x420804e6
[ 622][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_RX (11) successfully set to 0x420804e6
[ 623][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 8 successfully set to type INIT (0) with bus 0x0
[ 624][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 8 successfully set to type RMT_TX (10) with bus 0x408333f0
[ 626][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[ 626][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
LittleFsConfig: writing to file "/supla-dev.cfg"
LittleFsConfig: writing to file "/supla-dev.cfg.bak"
WiFi: establishing connection with SSID: "FRITZ!Box 7590 HN"
[ 723][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 101 - WIFI_READY
[ 798][V][STA.cpp:186] _onStaEvent(): STA Started
[ 798][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 110 - STA_START
[ 799][V][STA.cpp:110] _onStaArduinoEvent(): Arduino STA Event: 110 - STA_START
[ 867][V][STA.cpp:206] _onStaEvent(): STA Connected: SSID: FRITZ!Box 7590 HN, BSSID: 44:4e:6d:52:d4:81, Channel: 1, Auth: WPA2_PSK
[ 868][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 112 - STA_CONNECTED
[ 868][V][STA.cpp:110] _onStaArduinoEvent(): Arduino STA Event: 112 - STA_CONNECTED
[ 1890][V][NetworkInterface.cpp:78] _onIpEvent(): sta Got New IP: 192.168.178.96 MASK: 255.255.255.0 GW: 192.168.178.1
[ 1891][V][NetworkEvents.cpp:120] _checkForEvent(): Network Event: 115 - STA_GOT_IP
[ 1891][V][STA.cpp:110] _onStaArduinoEvent(): Arduino STA Event: 115 - STA_GOT_IP
[ 1891][V][STA.cpp:171] _onStaArduinoEvent(): STA IP: 192.168.178.96, MASK: 255.255.255.0, GW: 192.168.178.1
Connected BSSID: 44:4E:6D:52:D4:81
local IP: 192.168.178.96
subnetMask: 255.255.255.0
gatewayIP: 192.168.178.1
Signal strength (RSSI): -44 dBm
Connecting without certificate validation (INSECURE)
Establishing encrypted connection with: svr11.supla.org (port: 2016)
[ 1901][D][NetworkManager.cpp:83] hostByName(): Clearing DNS cache
[ 1958][D][NetworkManager.cpp:127] hostByName(): DNS found IPv4 188.34.204.56
[ 1959][V][ssl_client.cpp:68] start_ssl_client(): Free internal heap before TLS 245456
[ 1959][V][ssl_client.cpp:75] start_ssl_client(): Starting socket (domain 2)
[ 1984][V][ssl_client.cpp:170] start_ssl_client(): Seeding the random number generator
[ 1988][V][ssl_client.cpp:178] start_ssl_client(): Setting up the SSL/TLS structure...
[ 1990][D][ssl_client.cpp:196] start_ssl_client(): WARNING: Skipping SSL Verification. INSECURE!
[ 1990][V][ssl_client.cpp:292] start_ssl_client(): Setting hostname for TLS session...
[ 1991][V][ssl_client.cpp:313] ssl_starttls_handshake(): Performing the SSL/TLS handshake...
[ 2382][V][ssl_client.cpp:334] ssl_starttls_handshake(): Verifying peer X.509 certificate...
[ 2383][V][ssl_client.cpp:342] ssl_starttls_handshake(): Certificate verified.
[ 2383][V][ssl_client.cpp:358] ssl_starttls_handshake(): Free internal heap after TLS 206684
Connected via IP 192.168.178.96
SSL error: 48, UNKNOWN ERROR CODE (0030)
LAST STATE ADDED: UNKNOWN ERROR CODE (0030)
Connected to Supla Server
Initializing SRPC (proto: 23)
LAST STATE ADDED: Register in progress
[ 2384][I][Z2S_Gateway.ino:108] supla_callback_bridge(): event(0x22), action(0x4010)
Current status: [10] Register in progress
Send: [53 55 50 4C 41 17 01 00 00 00 4B 00 00 00 8E 02 00 00 7A 6F 6B 6F 70 69 61 6E 40 67 6D 61 69 6C 2E 63 6F 6D 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 87 D8 84 46 BE 8C 66 10 8D EE D0 51 5A 16 DF F5 0C 38 2B 83 7C B0 28 B2 E5 9E 2B EF B0 7E AB 0F 5A 69 67 62 65 65 20 3C 3D 3E 20 53 75 70 6C 61 20 47 61 74 65 77 61 79 00 00 00 00 00 00 00 00 00 00 ]
CH[110], type: 2900, FuncList: 0xEF, function: 130, flags: 0x009010000, online, validityTimeSec: 0, icon: 0, value: [00 00 00 00 00 00 00 00]
Send: [6E 54 0B 00 00 EF 00 00 00 82 00 00 00 00 00 01 09 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
CH[0], type: 2900, FuncList: 0xEF, function: 130, flags: 0x009010000, online, validityTimeSec: 0, icon: 0, value: [00 00 00 00 00 00 00 00]
Send: [00 54 0B 00 00 EF 00 00 00 82 00 00 00 00 00 01 09 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
[ 2401][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[ 2402][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[ 2402][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
Recv: [53 55 50 4C 41 17 01 00 00 00 46 00 00 00 07 00 00 00 03 00 00 00 78 1B 01 53 55 50 4C 41 ]
Device registered (activity timeout 120 s, server version: 27, server min version: 1)
LAST STATE ADDED: Registered and ready
[ 2450][I][Z2S_Gateway.ino:108] supla_callback_bridge(): event(0x22), action(0x4010)
[ 2451][I][Z2S_Gateway.ino:127] supla_callback_bridge(): Starting Zigbee subsystem
[ 2452][D][ZigbeeCore.cpp:180] zigbeeInit(): Initialize Zigbee stack
[ 2454][D][ZigbeeCore.cpp:187] zigbeeInit(): Register all Zigbee EPs in list
[ 2462][I][ZigbeeCore.cpp:195] zigbeeInit(): List of registered Zigbee EPs:
[ 2463][I][ZigbeeCore.cpp:197] zigbeeInit(): Device type: Home Gateway, Endpoint: 1, Device ID: 0x0050
[ 2468][V][ZigbeeCore.cpp:472] esp_zb_app_signal_handler(): ZDO signal: ZDO Config Ready (0x17), status: ESP_FAIL
[ 2469][I][ZigbeeCore.cpp:286] esp_zb_app_signal_handler(): Zigbee stack initialized
[ 2473][I][ZigbeeCore.cpp:432] esp_zb_app_signal_handler(): Network(0x688e) closed, devices joining not allowed.
[ 2474][I][Z2S_Gateway.ino:223] Z2S_onOpenNetwork(): Network closed
[ 2474][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[ 2475][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[ 2476][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
[ 2477][I][ZigbeeCore.cpp:292] esp_zb_app_signal_handler(): Device started up in non factory-reset mode
[ 2478][I][ZigbeeCore.cpp:305] esp_zb_app_signal_handler(): Device rebooted
[ 2478][I][ZigbeeCore.cpp:309] esp_zb_app_signal_handler(): Opening network for joining for 180 seconds
[ 2479][D][ZigbeeCore.cpp:631] searchBindings(): Requesting binding table for address 0x0000
[ 2480][D][ZigbeeCore.cpp:479] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[ 2480][D][ZigbeeCore.cpp:480] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 0, src_endpoint: 0, dst_addr_mode: 255
APSDE INDICATION - src_addr_mode: 255, cluster_id: 0x0033, asdu_length: 2
APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0x0000
APSDE INDICATION - profile_id: 0x0000, security_status: 0, lqi: 0, rx_time: 0
[ 2482][D][ZigbeeCore.cpp:479] zb_apsde_data_indication_handler(): APSDE INDICATION - Received APSDE-DATA indication, status: 0
[ 2483][D][ZigbeeCore.cpp:480] zb_apsde_data_indication_handler(): APSDE INDICATION - dst_endpoint: 0, src_endpoint: 0, dst_addr_mode: 255
APSDE INDICATION - src_addr_mode: 171, cluster_id: 0x8033, asdu_length: 26
APSDE INDICATION - dst_short_addr: 0x0000, src_short_addr: 0x0000
APSDE INDICATION - profile_id: 0x0000, security_status: 0, lqi: 0, rx_time: 0
[ 2485][D][ZigbeeCore.cpp:562] bindingTableCb(): Binding table callback for address 0x0000 with status 0
[ 2485][D][ZigbeeCore.cpp:565] bindingTableCb(): Binding table info: total 1, index 0, count 1
[ 2486][D][ZigbeeCore.cpp:578] bindingTableCb(): Binding table record: src_endp 1, dst_endp 1, cluster_id 0x0006, dst_addr_mode 3
[ 2486][I][z2s_devices_table.cpp:3873] Z2S_onBTCBoundDevice(): BTC bound device(0x3c37) on endpoint(0x1), cluster id(0x6)
[ 2487][I][z2s_devices_table.cpp:157] Z2S_findChannelNumberSlot(): 7C:B0:3E:AA:00:A3:90:EB, endpoint 0x1, channel type 0xffffffff
[ 2488][I][z2s_devices_table.cpp:191] Z2S_findChannelNumberNextSlot(): 7C:B0:3E:AA:00:A3:90:EB, endpoint 0x1, channel type 0xffffffff
[ 2488][I][ZigbeeGateway.cpp:1535] addBoundDevice(): New Zigbee device unit registered - IEEE address 7c:b0:3e:aa:0:a3:90:ebshort address 0x3C37, last seen (ms) 0
[ 2489][D][ZigbeeCore.cpp:599] bindingTableCb(): Device bound to EP 1 -> device endpoint: 40, short addr: 0x4082, ieee addr: 40:81:A8:CC:40:81:A8:CC
[ 2490][D][ZigbeeCore.cpp:622] bindingTableCb(): Filling bounded devices finished
- Telnet: [ 2493][V][NetworkServer.h:41] NetworkServer(): NetworkServer::NetworkServer(port=23, ...)
Telnet running
Current status: [17] Registered and ready
Changing activity timeout to 30 s
Send: [53 55 50 4C 41 17 02 00 00 00 D2 00 00 00 01 00 00 00 1E ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 17 03 00 00 00 E0 01 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
[ 2506][I][z2s_web_gui.cpp:3941] Z2S_buildWebGUI(): GUI building STARTED...
[ 2507][I][z2s_web_gui.cpp:729] fillGatewayGeneralnformation(): Device information <b><i>Supla firmware:</i></b> <i>0.9.113-23/10/2025</i><br><br><b><i>Supla GUID:</i></b> <i>0C382B837CB028B2E59E2BEFB07EAB0F</i><br><br><b><i>Z2S Gateway version:</i></b> <i>0.9.113-23/10/2025</i><br><br><b><i>Network extended PAN ID:</i></b> <i>E4:B3:23:FF:FE:B5:D2:D0</i><br><br>
[ 2510][I][z2s_web_gui.cpp:754] fillMemoryUptimeInformation(): Memory & uptime information <b><i>Flash chip real size:</b></i> 4194304 B <b>| <i>Free Sketch Space:</b></i> 2621440 B<br><b><i>HeapSize:</b></i> 359148 B <b>| <i>FreeHeap:</b></i> 133824 B <b>| <i>MinimalFreeHeap:</b></i> 133696 B <b>| <i>MaxAllocHeap:</b></i> 116724 B<br><b><i>uxTaskGetStackHighWaterMark:</b></i> 3600 B <br><b><i>Total PSRAM:</b></i> 0 B <b>| <i>Free PSRAM:</b></i> 0 B<br><br><b><i>Local time:</i></b> Fri Oct 24 18:39:08 2025
<b><i>Supla uptime:</i></b> 2 s
[ 2526][I][z2s_web_gui.cpp:1407] rebuildChannelsSelector():
channels_counter 0
current_option_id 87
channel_selector_first_option_id 87
[ 2527][I][z2s_web_gui.cpp:1419] rebuildChannelsSelector():
channel_selector_first_option_id 87
channel_selector_last_option_id 87
[ 2536][I][z2s_web_gui.cpp:3771] buildActionsTabGUI(): table html source length: 18
[ 2541][I][z2s_web_gui.cpp:4044] Z2S_buildWebGUI(): ...GUI building FINISHED
Recv: [53 55 50 4C 41 17 02 00 00 00 AD 02 00 00 1D 00 00 00 01 00 00 00 00 00 00 00 00 11 00 00 00 00 00 00 00 11 00 00 00 00 00 00 00 02 00 00 01 53 55 50 4C 41 ]
Received new device config
Processing StatusLed config
Processing AutomaticTimeSync config
Sending device config result OK (1)
Send: [53 55 50 4C 41 17 04 00 00 00 B7 02 00 00 0A 00 00 00 01 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Relay[110] updating timer value: remainingTime=0 state=0
SRPC sending: remaining time 0, channel 110, state 0
[ 2551][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[ 2552][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[ 2552][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
Send: [53 55 50 4C 41 17 05 00 00 00 69 00 00 00 E3 00 00 00 6E 32 DD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 17 03 00 00 00 AA 02 00 00 08 00 00 00 00 82 00 00 00 00 00 00 53 55 50 4C 41 ]
Channel[0] Received SetChannelConfig: fnc 130, config type 0, config size 0
Channel[0] handleChannelConfig, func 130, configtype 0, configsize 0
Relay[0] applyChannelConfig, func 130, configtype 0, configsize 0
Channel[0] ConfigType 0 SetChannelConfigNeeded
Channel[0] Sending SetChannelConfigResult OK (1)
Send: [53 55 50 4C 41 17 06 00 00 00 B4 02 00 00 03 00 00 00 01 00 00 ]
Send: [53 55 50 4C 41 ]
Relay[0] updating timer value: remainingTime=0 state=0
SRPC sending: remaining time 0, channel 0, state 0
Send: [53 55 50 4C 41 17 07 00 00 00 69 00 00 00 E3 00 00 00 00 32 DD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 17 04 00 00 00 AB 02 00 00 01 00 00 00 00 53 55 50 4C 41 ]
Channel[0] Received ChannelConfigFinished
Channel[0] some config is missing on server... (rcv: 0x1 != used: 0x2)
Send: [53 55 50 4C 41 17 08 00 00 00 80 02 00 00 26 00 00 00 6E DD 00 00 1E 00 00 00 47 61 74 65 77 61 79 20 73 65 6E 73 6F 72 73 20 6E 6F 74 69 66 69 63 61 74 69 6F 6E 73 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 17 05 00 00 00 AA 02 00 00 32 00 00 00 6E 82 00 00 00 00 2A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 53 55 50 4C 41 ]
Channel[110] Received SetChannelConfig: fnc 130, config type 0, config size 42
Channel[110] handleChannelConfig, func 130, configtype 0, configsize 42
Relay[110] applyChannelConfig, func 130, configtype 0, configsize 42
Relay[110] OvercurrentMaxAllowed: 0, OvercurrentThreshold: 0
Channel[110] ConfigType 0 applied
Channel[110] Sending SetChannelConfigResult OK (1)
Send: [53 55 50 4C 41 17 09 00 00 00 B4 02 00 00 03 00 00 00 01 00 6E ]
Send: [53 55 50 4C 41 ]
Send: [53 55 50 4C 41 17 0A 00 00 00 80 02 00 00 15 00 00 00 00 00 00 00 0D 00 00 00 50 4F 57 45 52 20 53 57 49 54 43 48 00 ]
Send: [53 55 50 4C 41 ]
Recv: [53 55 50 4C 41 17 06 00 00 00 AB 02 00 00 01 00 00 00 6E 53 55 50 4C 41 ]
Channel[110] Received ChannelConfigFinished
ConfigTypesBitmap: Set all to 0x2
Relay[0] fill channel config for power switch functions (or ext for staircase)
Send: [53 55 50 4C 41 17 0B 00 00 00 A9 02 00 00 32 00 00 00 00 82 00 00 00 00 2A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ]
Send: [53 55 50 4C 41 ]
Channel[0] SetChannelConfig send, func 130, type 0
Recv: [53 55 50 4C 41 17 07 00 00 00 DC 00 00 00 03 00 00 00 1E 0A F0 53 55 50 4C 41 ]
Activity timeout set to 30 s
Recv: [53 55 50 4C 41 17 08 00 00 00 EA 01 00 00 1A 00 00 00 E9 07 0A 18 06 12 27 09 0E 00 00 00 45 75 72 6F 70 65 2F 57 61 72 73 61 77 00 53 55 50 4C 41 ]
Clock: current time: 2025-10-24 18:39:08
Clock: time diff (system-new): -1 s
Clock: new time: 2025-10-24 18:39:09
Recv: [53 55 50 4C 41 17 09 00 00 00 8A 02 00 00 27 00 00 00 6E DD 00 00 1A 1E 00 00 00 47 61 74 65 77 61 79 20 73 65 6E 73 6F 72 73 20 6E 6F 74 69 66 69 63 61 74 69 6F 6E 73 00 53 55 50 4C 41 ]
Channel[110] Receieved setChannelCaptionResult
[ 2946][I][ZigbeeCore.cpp:427] esp_zb_app_signal_handler(): Network(0x688e) is open for 180 seconds
[ 2947][I][Z2S_Gateway.ino:216] Z2S_onOpenNetwork(): Network open for 180 s
[ 2947][V][esp32-hal-rmt.c:490] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
[ 2948][V][esp32-hal-rmt.c:307] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
[ 2948][V][esp32-hal-rmt.c:315] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Loop Request: [NO], LoopCancel: [NO]
Recv: [53 55 50 4C 41 17 0A 00 00 00 8A 02 00 00 16 00 00 00 00 00 00 00 03 0D 00 00 00 50 4F 57 45 52 20 53 57 49 54 43 48 00 53 55 50 4C 41 ]
Channel[0] Receieved setChannelCaptionResult
Recv: [53 55 50 4C 41 17 0B 00 00 00 B3 02 00 00 03 00 00 00 01 00 00 53 55 50 4C 41 ]
Channel[0] Set channel config succeeded (1) for config type 0
Recv: [53 55 50 4C 41 17 0C 00 00 00 AA 02 00 00 32 00 00 00 00 82 00 00 00 00 2A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 53 55 50 4C 41 ]
Channel[0] Received SetChannelConfig: fnc 130, config type 0, config size 42
Channel[0] handleChannelConfig, func 130, configtype 0, configsize 42
Relay[0] applyChannelConfig, func 130, configtype 0, configsize 42
Relay[0] OvercurrentMaxAllowed: 0, OvercurrentThreshold: 0
Channel[0] ConfigType 0 applied
Channel[0] Sending SetChannelConfigResult OK (1)
Send: [53 55 50 4C 41 17 0C 00 00 00 B4 02 00 00 03 00 00 00 01 00 00 ]
Send: [53 55 50 4C 41 ]
[ 5001][I][ZigbeeGateway.cpp:1806] sendAttributeRead(): Sending 'read attribute' command
LittleFsConfig: writing to file "/supla-dev.cfg"
LittleFsConfig: writing to file "/supla-dev.cfg.bak"
PowerCycle: timeout, counter reset to 0
LittleFsConfig: writing to file "/supla-dev.cfg"
LittleFsConfig: writing to file "/supla-dev.cfg.bak"
8x SRW-01, 1x SBW-01, 1x MEW-01,
10x TH 10, 7x Touch, 1x SV, 1x Basic R2,
2x S26, 4x mini, 2x POW R2, 1x S55,
3x Shelly 1, 1x nodemcu + BME 280,
2x H801. 4x Nous a1, 4x SP111, 2x NEO
1x MoesHouse, 2x SMTONOFF SMT002
1x Sonoff POW R3 25A
10x TH 10, 7x Touch, 1x SV, 1x Basic R2,
2x S26, 4x mini, 2x POW R2, 1x S55,
3x Shelly 1, 1x nodemcu + BME 280,
2x H801. 4x Nous a1, 4x SP111, 2x NEO
1x MoesHouse, 2x SMTONOFF SMT002
1x Sonoff POW R3 25A
-
YoMan
- Posts: 3522
- Joined: Thu Apr 30, 2020 5:18 pm
- Location: Częstochowa
- Has thanked: 3 times
- Been thanked: 3 times
Code: Select all
Slot# 03 | Manufacturer name _TZE200_rtrmfadk | model ID TS0601 | Z2S model Unknown Zigbee model [0x6011]
IEEE address A4:C1:38:E8:22:60:0F:B4 | Short address 0xD8B4 | Power source 0x03YoMan
________________________________________
Wziąłem udział w SOP2023 & SOP2024
________________________________________
Wziąłem udział w SOP2023 & SOP2024
-
vajera
- Posts: 7293
- Joined: Wed Oct 31, 2018 7:58 am
- Location: Biedrusko
- Has thanked: 291 times
- Been thanked: 161 times
Sprawdź 0.9.114-25/10/2025zokopian wrote: Fri Oct 24, 2025 4:51 pm Urządzenie sparowało się, przedstawia się jako power switch, nie działa załączanie i wyłączanie z aplikacji. Po załączeniu z palca status w aplikacji nie zmienia się.
Bramka Zigbee <=> SUPLA
Więcej informacji tutaj:
https://forum.supla.org/viewforum.php?f=127
FAQ https://forum.supla.org/viewtopic.php?t=17277
Więcej informacji tutaj:
https://forum.supla.org/viewforum.php?f=127
FAQ https://forum.supla.org/viewtopic.php?t=17277
-
vajera
- Posts: 7293
- Joined: Wed Oct 31, 2018 7:58 am
- Location: Biedrusko
- Has thanked: 291 times
- Been thanked: 161 times
Ona jest w bazie - zresztą ten wpis, który wrzuciłeś pochodzi z GUI - urządzenie jest na liście dodanych?YoMan wrote: Sat Oct 25, 2025 9:11 amprośba o dodanie - głowica Avatto trv10 (to tutaj czy w dziale "głowice") ??Code: Select all
Slot# 03 | Manufacturer name _TZE200_rtrmfadk | model ID TS0601 | Z2S model Unknown Zigbee model [0x6011] IEEE address A4:C1:38:E8:22:60:0F:B4 | Short address 0xD8B4 | Power source 0x03
Bramka Zigbee <=> SUPLA
Więcej informacji tutaj:
https://forum.supla.org/viewforum.php?f=127
FAQ https://forum.supla.org/viewtopic.php?t=17277
Więcej informacji tutaj:
https://forum.supla.org/viewforum.php?f=127
FAQ https://forum.supla.org/viewtopic.php?t=17277
-
PijanySmerf
- Posts: 183
- Joined: Sun Apr 18, 2021 7:45 pm
- Location: Dąbrowa Tarnowska
Code: Select all
Unknown model _TZE284_1lvln0x6::TS0601, no binding is possible-
YoMan
- Posts: 3522
- Joined: Thu Apr 30, 2020 5:18 pm
- Location: Częstochowa
- Has thanked: 3 times
- Been thanked: 3 times
hmmm... zmyliło mnie "Unknown Zigbee model" oraz to że nie działavajera wrote: Sat Oct 25, 2025 9:40 amOna jest w bazie - zresztą ten wpis, który wrzuciłeś pochodzi z GUI - urządzenie jest na liście dodanych?YoMan wrote: Sat Oct 25, 2025 9:11 amprośba o dodanie - głowica Avatto trv10 (to tutaj czy w dziale "głowice") ??Code: Select all
Slot# 03 | Manufacturer name _TZE200_rtrmfadk | model ID TS0601 | Z2S model Unknown Zigbee model [0x6011] IEEE address A4:C1:38:E8:22:60:0F:B4 | Short address 0xD8B4 | Power source 0x03
OK. Walczę dalej
YoMan
________________________________________
Wziąłem udział w SOP2023 & SOP2024
________________________________________
Wziąłem udział w SOP2023 & SOP2024